• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.2
• /
• pp.311-316
• /
• 2007

This paper proposes the algorithm which estimates moment of the inertia and friction coefficient of friction for high performance speed control of electric motor. The proposed algorithm finds the moment of inertia and friction coefficient of friction by observing the speed error signal generated by the speed observer and using Recursive Least-Mean-Square method(RLS). By feedbacking the estimated inertia and estimated coefficient of friction to speed controller and full order speed observer, then the errors of the inertia and coefficient of friction and speed due to the inaccurate initial value are decreased. Inertia and coefficient of friction converge to the actual value within several times of speed changing. Simulation and actual experiment results are given to demonstrate the effectiveness of the proposed parameter estimator.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.1
• /
• pp.67-74
• /
• 2000

Recently, PTFE-polymide composites are being used self-lubricating parts for industrial field. Thus, this study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polymide composites. The friction and wear test was carried out for the different composition ratio under the atomsphere room temperature and constant load of 7.69N and their friction and wear properties were compared with each other at various sliding speed. notable results are summarized as follows. PTFE 100% showed that friction coefficient was almost same values at 0.94 and 1.88m/s but the value was decreased at 2.83m/s because the friction temperature is higher than low speed. PTFE 80%-PI 20% showed the lowest mean friction coefficient at 2.83m/s. PTFE 20-PI 80% showed the highest friction coefficient at 0.94m/s and the value was decreased at high speed but the value is higher than other materials except PTFE 100 %. PI 100% showed the highest friction coefficient at 0.94 and 1.88m/s becuase adhesive wear mainly occurred that speed. PTFE 100% showed highest specific wear rate on the whole. Specific wear rate of PTFE 80%-PI 20% was almost the same value with PTFE 20%-PI80%. PI 100%showed the lowest value at high sliding speed because the friction surface was thicken and carbonated by high friction temperature.

• Fashion & Textile Research Journal
• /
• v.7 no.6
• /
• pp.673-679
• /
• 2005

This study surveys the fabric surface properties such as mean value of the coefficient of friction(MIU), mean deviation of the coefficient of friction(MMD) and mean deviation of surface roughness(SMD) due to warp and weft tension differences using KES-FB system. For this purpose, fabric is designed as 5 harness Satin weave using 150d/48f warp and 200d/384f weft polyester filaments, and is woven by Omega$^{(R)}$ rapier loom by Textec Co.Ltd and Vamatex-P1001ES$^{(R)}$ rapier loom by Vamatex Co.Ltd respectively. These grey fabrics are processed on the same dyeing and finishing processes. The fabric surface properties according to the weaving looms are analysed with warp and weft weaving tensions. And also surveyed the difference of fabric surface properties according to the fabric positions such as center and each edge of fabrics for the sensitive garment. Fabric thickness was also measured and discussed according to the fabric positions such as center and each of fabrics with two looms weaving tensons.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.88-94
• /
• 1999

Recently, PTFE-polyimide composites are being used self-lubricating parts for industrial field. Thus, this study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polyimide composites. The friction and wear test was carried out for the different composition ratio under the atmosphere room temperature and constant load of 7.69N and their friction and wear properties were compared with each other at various sliding speed. Notable results are summarized as follows. PTFE 100% showed that friction coefficient was almost same values at 0.94 and 1.88m/s but the value was decreased at 2.83m/s because the friction temperature is higher than low speed. PTFE 80%-PI 20% showed the lowest mean friction coefficient at 2.83m/s. PTFE 20%-PI 80% showed the highest friction coefficient at 0.94m/s and the value was decreased at high speed but the value is higher than other materials except PTFE 100 %. PI 100% showed the highest friction coefficient at 0.94 and 1.88m/s because adhesive wear mainly occurred that speed. PTFE 100% showed highest specific wear rate on the whole. Specific wear rate of PTFE 80%-PI 20% was almost the same value with PTFE 20%-PI 80%. PI 100% showed the lowest value at high sliding speed because the friction surface was thicken and carbonated by high friction temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.28-31
• /
• 2001

Friction for sheet metal forming affects improvement of deep drawing formability. The deep drawing is affected by many process variables, such as lubricant, blank shapes, shape radius and so on. Especially, lubrication is very important formability factor. In this study, in order to investigate fraction coefficient of sheet metal forming, we examined friction test about three conditions, such as non-lubrication, full lubrication and film lubrication. We measured friction coefficient according to pin load under the conditions like deep drawing die. Mean friction coefficient for film lubrication condition would be very useful value to improve drawability.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.766-771
• /
• 2000

This study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polyimide composites. At the PTFE and polyimide alone mixture specimens, PTFE80%-polyimide20%, which shows the lowest men friction coefficient and specific wear rate at 0.94m/s sliding speed. At each of carbon, copper and oxide lopper mixed with PTFE80%-polyimide20%. In case of copper10%, at 0.94m/s sliding speed, the mean friction coefficient shows 0.087, which is the lowest value in all specimens. In case of the specific wear rate, copper30% specimen shows the lowest value of $2.537E-5(mm^3/Nm)$ in all specimens.

• Science of Emotion and Sensibility
• /
• v.7 no.4
• /
• pp.25-33
• /
• 2004

This study surveys the fabric surface properties such as mean value of the friction coefficient(MIU), mean deviation of the friction coefficient(MMD) and mean deviation of surface roughness(SMD) due to warp and weft tension differences using KES-FB system. For this purpose, fabric is designed as 5 harness Satin weave using 75d/36f warp and 100d/192f weft polyester filaments, and is woven by OmegaR rapier loom by Textec Co.Ltd and Picanol-GTXR rapier loom by Picanol Co.Ltd respectively. These grey fabrics are processed on the same dyeing and finishing processes. The fabric surface properties according to the weaving looms are analysed with warp and weft weaving tensions. And also surveyed the difference of fabric surface properties according to the fabric positions such as center and each edge of fabrics for the sensitive garment.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.813-819
• /
• 2008

For the wear characteristics assessment of Saemaul train passing through curves, an analysis model for multi-car system has been developed. By using this model and ADAMS/Rail, sensitivity analyses have been conducted for the wear characteristics by changing the related parameters. According to the increase of running speed, the wear number, the sliding mean and friction coefficient were increased. At high speed, the wear number, the sliding mean and friction coefficient of left wheel showed higher than right wheel. If the cant increased, the wear number the sliding mean and friction coefficient increased. but decreased based on the balance cant value by the curvature and running speed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.367-373
• /
• 2001

The effect of characteristic of surface roughness and roughness patterns on friction and sliding wear was studied experimentally under reciprocating boundary lubricant sliding conditions. The test was conducted with specimens which have various arithmetic mean value and roughness pattern under the condition of different normal load. The experimental results show that the friction coefficient is decreased because of oxidation mass and valley effect as the normal loads increasing It was found that the specimens with surface roughness with a transverally oriented pattern have a smaller firction coefficient than the other two roughness patterns under the condition of the roughness values of Ra=0.5 and Ra=0.2 .

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.2
• /
• pp.18-24
• /
• 2004

The effect of surface characterization parameters, such as surface roughness, skewness and kurtosis, on sliding friction and wear was studied experimentally. The friction coefficient was examined under the various parameters and sliding speed, normal load and type of lubricant with ball-on-disk type tribo-meter. The surface of the lower skewness in negative or the higher kurtosis between the same arithmetic mean value tends to indicate low friction.