• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.336-338
• /
• 2006

Diagnostic tests are used to evaluate the insulation condition of stator windings in traction motor. These tests included ac current, tan delta and maximum partial discharge. The insulation condition of stator windings was assessed by three test items. The stator windings of traction motor were m good condition. After completing the diagnostic tests, the stator windings of traction motors were subjected to gradually increasing ac voltage, until the insulation punctured. No.5 stator windings failed near rated voltage of 18.9 kV. The breakdown voltage of No.1 stator windings was 13.0. The failure was located m a line-end coil at the exit from the core slot.

• Journal of Electrical Engineering and Technology
• /
• 제8권1호
• /
• pp.118-123
• /
• 2013

This paper presents performance comparison between concentrated winding and distributed winding of IPMSM (Interior Permanent Magnet Synchronous Motors) which is recently used for light-weight railway applications. Motors are designed on various schemes and analyzed by using FEM (Finite Element Method) instead of EMCNM (Equivalent Magnetic Circuit Network Method) in order to take into account saturation and non-linear magnetic property. The overall performance such as torque, torque ripple, losses, demagnetization, efficiency, power density and so on are investigated in detail at the rated and maximum operating speed. The results of the analysis found that both concentrated and distributed winding IPMSMs are promising candidates for high power railway traction motor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.950-954
• /
• 1998

This paper describes a development of traction unit for 2-motor driven electric vehicle (EV). The traction unit is consisted with an interior permanent magnet synchronous motor (IPMSM), a reduction gear and an inverter for electric vehicle that is driven by 2 motors without differential gear. For traction unit, prototype IPMSM and inverter have been developed. The IPMSM was designed by CAD program that was developed with both equivalent circuit method and FEM. Also the inverter was developed to drive 2 motors with 6 legs IGBT switches in a control board. The vector control algorithm was implemented with maximum torque control method in the constant torque region and field weakening control method in the constant power region considering inverter capacity. To verify that the traction unit is more high efficiency and has more high power density than a traction unit with induction motor with the same power, we would like to show the results about the design and analysis of the IPMSM and the experiment results about the traction unit.

• 산업기술연구
• /
• 제20권B호
• /
• pp.95-103
• /
• 2000

A model trains must have similitude with its original model not only in shape but also in motion. Motion characteristics of a model train under considerations are maximum velocity in straight and circular tracks and stopping distance. Equations of motions are derived to obtain maximum speed and stopping distance based on the Newton's Second Law and the energy principal. To accurately predict traction and resistance force between wheel and rail. wheel slip, or creepage, is taken into consideration. To verify the equations of motion, various experiments have been carried out including measurement of gear efficiency, location of mass center, rolling resistance force, traction force, slip, maximum velocity and stopping distance. This paper addresses how the experiments are setup and carried out in detail. Also the results of experiments are compared with the analytical prediction, which showed good agreements with each other.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1320-1326
• /
• 2011

The maximum speed of high-speed rail is restricted to various factors such as track condition including slope and radius, tunnel and dynamic stability of vehicle. Among the various factors, traction effort and resistance to motion is principal and basic factor. In addition, at high speed over 300km/h, aerodynamic drag amounts up to 80% of resistance to motion, that it can be said that aerodynamic drag is the most important factor to decide the maximum speed of high-speed rail system. This paper deals with a measure to increase the maximum speed of high-speed train by reducing aerodynamic drag. The traction effort curve and resistance to motion curve of existing high-speed train under development has been employed to set up the target of aerodynamic drag reduction to reach up to 500km/h without modification traction system. In addition, the contribution of various sources of aerodynamic drag to total value has been analyzed and the strategy for implementation of aerodynamic drag reduction has been discussed based on the aerodynamic simulation results around the train using computational fluid dynamics.

• 한국산학기술학회논문지
• /
• 제7권3호
• /
• pp.265-270
• /
• 2006

복합재로 된 판재에 대하여 동적 균열이 접합면을 따라서 진행되어 가면서 찢어져 나갈 때 그 계면 주위에서의 응력 상태 및 변형, 견인응력 등을 조사하였다. 최대의 등가응력 및 소성 변형율은 접촉이 바로 떨어지는 부분에서 그리고 판 끝부분의 휘어지는 부근에서 최대의 변형량이 되었다. 견인력은 0.015mm정도로 그 면이 떨어졌을 때 최대치 75 MPa로서 되었다가 서서히 낮아지면서 0.13mm이상 떨어졌을 때는 0으로 일정하게 되었다. 이러한 연구 자료로서 정확한 파괴강도 해석과 안전설계 및 새로운 고급재료의 개발에 필요한 자료를 제공할 수 있는 기초적인 연구를 수행함이 본 연구의 목적이다.

• 한국정보전자통신기술학회논문지
• /
• 제2권2호
• /
• pp.3-8
• /
• 2009

척추 및 보행질환 등에서 재활과 교정을 위하여 정형외과 및 가정 등에서는 견인운동치료기를 주로 사용하고 있다. 하지만 견인운동치료기를 사용함에 있어 간혹 무리하게 사용함에 따라 인체에 문제점이 발생하고 있다. 지속적인 견인력 작용을 이용한 치료방법에 견인운동치료기를 이용하는데, 이 때 작용하는 견인력을 측정하여 운동 시간을 조절할 필요가 있다. 그러나 현재 출시되고 있는 제품에는 견인력을 측정하는 센서가 대부분이 장착되어 있지 않고 있다. 그래서 스트레인 게이지를 이용한 견인측정센서, 출력신호로서의 변환을 위한 증폭기 및 성능 검증을 위하여 측정용 실험 장치를 설계 제작하고, 이를 이용하여 견인측정센서를 실험 하였다. 견인 부하에 따른 견인측정센서의 전기적 반응치를 측정하고 분석 결과, 캘리브레이션을 통하여 센서는 선형적인 출력을 보였고 환자의 움직임 여부에 관계없이 일정하게 견인측정센서의 반응이 나타남을 알 수가 있었다. 정적인 상태에서의 실험에서 최대 에러율이 약 1%이내이고, 동적인 실험에서 평균 에러율이 약 0.7%로 나타났다. 온도 변화에 따른 견인측정센서의 최대 출력치 변화량(output variation)이 약 0.3%이므로 견인 측정용 센서로 사용 가능하다고 판단된다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.291-292
• /
• 2002

Using a low viscosity synthetic traction oil and a low viscosity mineral oil with nearly equal viscosity grade of ISO VG 32, the effect of kind of oil on the fatigue life of bearing steel rollers was examined. A pair of rollers finished the contact surfaces to a mirror-like condition were driven under rolling with sliding conditions of s = -3.2% and a maximum Hertzian stress in the range of $P_H=2.8GPa{\sim}4.0GPa$ was applied in point contact condition. As a result of experiments, the fatigue life with a mineral oil was longer than that with a traction oil under higher stress conditions above $P_H=3.4GPa$. Based on the numerical calculation results of the thermal EHL which simulates the present experiment, the authors discuss the reason why such a difference in the fatigue life comes out.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1642-1646
• /
• 2011

One of the rolling stocks, low floor tram is recognized as the important alternative to improve traffic and environmental problems. There are many advantages of tram transportation system. It has, especially, low construction costs and easy accessibility. Trams operate with vehicles on roadways. The bogie configuration including traction motor of tramcar is different from that of conventional electric trains because tram has lower floor than train. In these reasons, the traction motors of tramcar are exposed to dusts, water and so on. Therefore, motors are designed by totally enclosed type. In this paper, we explain the design and test of totally enclosed traction motor for tramcar. Characteristic tests and temperature-rising tests were carried out in order to predict the performance of motor and the maximum temperature of coil.

• 대한전기학회논문지:전력기술부문A
• /
• 제52권11호
• /
• pp.639-646
• /
• 2003

Nowadays traction motors in the urban rail transit vehicle are controlled by VVVF inverter and have capability of regenerative braking. The algorithms to deal with the regenerating vehicle in simulation for the DC traction power supply is introduced in this paper. Substations have to be separated from the system to represent reverse biased rectifiers in substations. The model of the trains in regenerative braking has to be changed from the ideal current source to the constant voltage source since the train input voltage has to be controlled below the certain train maximum voltage. Some mismatches are unevitable because the constraint of the regenerated power can not be imposed with the constant voltage source. The mismatches represent the unused regenerated power. A computer program is developed to verify the validity of the algorithm. The test run result shows the program behaves as it is expected and proves the algorithm's validity.