• Journal of Korea Foundry Society
• /
• v.7 no.4
• /
• pp.366-379
• /
• 1987

The influences of some factors on the variation of compression strength of $CO_2$ process were investigated with an attention given to use of high $SiO_2\;/Na_2O$ silicate, addition of organics and gassing operation. 1) Higher ratio binder offers faster rates of hardening with lower $CO_2$ consumption requiring more concentration for a good strength development. A mixture containing 4 percent of 2.7:1 ratio silicate produces the strength above $8kg\;/\;cm^2$ after 80 seconds gassing, but 5% and 6% respectively of 3.0:1 and3.3:1 ratio silicate are necessary to achieve equivalent levels of strength. 2) The correct water content in sand mixtures containing higher ratio silicates is necessary for the better strength properties to be obtained. The addition of 1% water to the sand mixtures bonded with 5%,3:1 ratio and 6%,3.3:1 ratio silicates maintains near-maximum strength on extended gassing. 3) When higher ratio silicates with 3:1 and 3.3:1 ratios are used,the addition of organic additives such as oil, sucrose and polyol results in considerable changes in strength. The presence of 1.0 to 1.5 percent of polyol produces a noticiable improvement 4) Gas diluted with air raises the efficiency of gas utilization. When gas contains 50 percent $CO_2$, the efficience is significantly increased with the best strength in the silicates having high ratios of 3:1 and 3.3:1. 5) The strength of molds is liable to change on storage with the reduction in water content. The magnitude of the strength change is determinded with the mole ratio. The presence of polyol in the mixture with 3.3:1 ratio silicate has a pronounced effect on maintaining the gassed strength.

• Korean journal of food and cookery science
• /
• v.8 no.3
• /
• pp.333-341
• /
• 1992

The physicochemical, rheological and sensory characteristics of 'BACKSULGIES', which was added with potato peel, guar gum or polydextrose, were investigated. The maximum acceptable addition ratio of dietary fiber to 'BACKSULGI' was 10%. And optimal addition ratio was 3% for all samples. The water binding capacity was affected by dietary fiber sources and incubation conditions (temperature and time). The Guar gum had me highest value of water binding capacity. The solubility was highly related with water binding capacity and me swelling power was increased with temperature increment. The degree of gelatinization was not significantly different with dietary fiber sources. But me values of gelatinization of 'BACKSULGIES' added with dietary fibers were significantly higher than mose of 'BACKSULGI' with no dietary fiber. Generally hardness and brittleness incresed along with storage time. But me hardness of 'BACKSULGIES' added with dietary fibers was significantly lower man those of 'BACKSULGI' with no dietary fiber. The retardation effect of dietary fibers for retrogradation of 'BACKSULGIES' was also proved by time constant determination of Avrami equation. Sernsory evaluation revealed that me addition of dietary fibers did not reduce the organoreptic quality. Therefore potato peel 3%, guar gum 3%, polydextrose 3% were optimum addition ratio which could be accepted as conventional 'BACKSULGI'. As me results of this study, it was proved mat the additions of dietary fibers to 'BACKSULGI' had the retardation effect of retrogradation.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.3
• /
• pp.153-164
• /
• 2018

Calculating the relevant length of left turn storages in urban intersections is very crucial in road designs. A left turn lane consists of deceleration lanes and left turn storages. In this study, we developed methods for calculating relevant lengths of left turn storages that vary at each intersection using UAV (Unmanned Aerial Vehicle) spatial images. Problems of conventional design techniques are applying the same number of left turn vehicles (N) using Poisson distribution without considering land use types, using a vehicle length that may not be measurable when applying the length of waiting vehicles (S), and using same storage length coefficient (${\alpha}$), 1.5, for every intersections. In order to solve these problems, we estimated the number of left turn vehicles (N) using an empirical distribution, suggested to use headways of vehicles for (S) to calculate the length of waiting vehicles (S) with a help of using UAV spatial images, and defined ranges of storage length coefficient (${\alpha}$) from 1.0 to 1.5 for flexible design. For more convenient design, it is suitable to classify two cases when possible to know and impossible to know about ratio of large trucks among vehicles when planning an intersection. We developed formula for each case to calculate left turn storage lengths of a minimum and a maximum. By applying developed methods and values, more efficient signalized intersection operation can be accomplished.

• Fire Science and Engineering
• /
• v.32 no.1
• /
• pp.76-80
• /
• 2018

The present study investigates the hydrodynamic force acting on the vertical wall of a portable water storage tank which has reentrant bottom topology. To numerically simulate the lapping waves in the tank, functional iterative method for the linearized Peregrine's model which numerically simulates the propagating waves over the slowly-sloped bottom topology is introduced. The numerical experiment condition is controlled to adjust the position and the height of the water supplying nozzle. Finally, it is observed that the maximum wave height at the vertical wall and the ratio of hydrodynamic force to hydrostatic one are amplified accordingly. Therefore it must be give attention to this bad effect of amplified hydrodynamic force by the supply method of fire water in order to have the structural stability of the portable water storage tank when it was used on the reentrant bottom topography.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.68-73
• /
• 2011

An experimental study was conducted to investigate the thermal performance of a medium-temperature heat pipe against the charge amount of working fluid. The container and the wick of the heat pipe were made of stainless steel and the working fluid was Dowtherm-A for medium-temperature applications around $250^{\circ}C$. The diameter and length of the heat pipe were 25.4 mm and 1 m, respectively. The maximum thermal load was 1 kW and the working fluid charge ratio varied from 372% to 420%. The results showed that the thermal resistance ranged from 0.12 to $250^{\circ}C/W$ and the effective thermal conductance ranged from 7,703 to $8,898 W/m{\cdot}K$. Dry-out occurred for the heat pipe with 372% fill-charge at the heat load of 950 W, while the other heat pipes with higher charge amount did not encounter dry-out up to 1060 W.

• Journal of Biosystems Engineering
• /
• v.43 no.2
• /
• pp.94-102
• /
• 2018

Purpose: In this study, a maintenance free super-capacitor battery charging system based on the photovoltaic module, to be used in agricultural electric carriers, was developed and its charging characteristics were studied in detail. Methods: At first, the electric carrier system configuration is introduced and the electric control components are presented. The super-capacitor batteries and photovoltaic module used in the experiment are specified. Next, the developed charging system consisting of a constant current / constant voltage Buck converter as the charging device and a super-capacitor cell as a balancing device are initiated. The proposed circuit design, a developed PCB layout of each device and a proportional control to check the current and voltage during the charging process are outlined. An experiment was carried out using a developed prototype to clarify the effectiveness of the proposed system. A power analyzer was used to measure the current and voltage during charging to evaluate the efficiency of the energy storage device. Finally, the conclusions of this research are presented. Results: The experimental results show that the proposed system successfully controls the charging current and balances the battery voltage. The maximum voltage of the super-capacitor battery obtained by using the proposed battery charger is 16.2 V, and the maximum charging current is 20 A. It was found that the charging time was less than an hour through the duty ratio of 95% or more. Conclusions: The developed battery charging system was successfully implemented on the agricultural electric carriers.

• Textile Coloration and Finishing
• /
• v.3 no.1
• /
• pp.8-16
• /
• 1991

In order to investigate the fine structure of PET films, PET films were stretchd at various draw ratios (2, 3, 4, 5) below $T_g$ ($72^{\circ}C$) and then annealed at various temperatures (125, 150, 175, $200^{\circ}C$) under free-annealed (FA) and taut-annealed (TA) conditions. Such changes as thermal shrinkage, crystallinity, crystallite size, dynamic viscoelasticity and thermal behaviour were measured in relation to the draw ratio and annealing condition.The following results were obtained. 1. Thermal shirinkage increased with increasing annealing temperature and draw ratio, but decreased in case of draw ratio 4 (draw ratio 3 at $200^{\circ}C$) and above it. 2. The degree of crystallinity of FA samples were higher than those of TA samples. 3. Tan 5 of TA samples were less than those of FA samples, and storage moduli (E') and loss moduli (E") of FA samples were less than those of TA samples; moreover, maximum tan '||'&'||' temperature of FA samples were shifted toward higher temperature than those of TA samples. 4. The melting endotherm ($T_m$) and heat of fusion $(\DeltaH)$ of the PET film increased with the draw ratio and annealing temperature; in addition, premelting endotherm ($T_m$) and heat of fusion $(\DeltaH)$ of the local crystallization in the FA samples were larger than those of TA samples. 5. The X-ray diffraction pattern displayed sharp peaks gradually with the draw ratio and annealing temperature. 6. Crystallite sizes of FA samples were larger than those of TA samples.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.5 no.11
• /
• pp.2103-2120
• /
• 2011

In this research, we consider the replication strategy for the applications of video streaming in wireless mesh networks (WMNs). In particular, we propose a closed-form of optimal replication densities for a set of frames of a video streaming by exploiting not only the skewed access probability of each frame but also the skewed loss probability and skewed encoding rate-distortion information. The simulation results demonstrate that our method improves the replication performance in terms of user-perceived quality (UPQ) which includes: 1) minimum average maximum reconstructed distortion for high peak signal-to-noise ratio (PSNR), 2) small reconstructed distortion fluctuation among frames for smooth playback, and 3) reasonable average maximum transmission distance for continuous playback. Furthermore, the proposed strategy consumes smaller storage capacity compared to other existing optimal replication strategies. More importantly, the effect of encoding rate is carefully investigated to show that high encoding rate does not always gain high performance of replication for video streaming.

• Solar Energy
• /
• v.12 no.2
• /
• pp.1-8
• /
• 1992

Identifying characteristics of heating and cooling systems requires estimation of thermal load of specific time interval, especially in cases that its system is operated intermittently, by using thermal storage, of in a partial load condition. Estimating the thermal load, however, needs to forecast hourly weather data variation. Hence, this paper attempts to examine characteristics of hourly ourdoor temperature variation as a preliminary research for the mathematical modeling of the hourly weather variation. Speculating characteristics of daily minimum and maximum temperature occurances, hourly outdoor temperature variation, and daily temperature differences in the increasing range ($07h{\sim}15h$) and decreasing range($15h{\sim}07h$), we were able to analyze changing patterns of daily temperature differences in each range in terms of daily solar amount, cloud ratio, and other weather data. Results from the multiple regression analysis enables us to conclude that daily differences in the increasing range are strongly affected last night temperature itself while the other range's differences are influenced by many weather data, which are solar amount, the variation of cloud, and the maximum temperature of the previous day.

• Food Science and Preservation
• /
• v.9 no.3
• /
• pp.277-281
• /
• 2002

To decrease the rot of onion bulb during storage in simple house, later cultivar 'Changnyeungdaego' was dried after harvest on the field, ventilation house and non-ventilation house during 1 to 3days in 1997 and 1998. The maximum air temperature during pre-drying maintained highest in the non-ventilation house and lowest in the field, especially higher than 41.6$^{\circ}C$ at second and third day in 1997 and second day in 1998 on the non-ventilation house. Water content of onion bulbs showed 90.3∼89.5% at harvest and reduced 0.3∼l.8% in 1997, 0.2∼2.6% in 1998 after pre-drying, the rate of reduction was highest on the field and lowest on the ventilation house. Mean of maximum air temperature was 39.2$^{\circ}C$ in 1997 and 37.1$^{\circ}C$ in 1998 and relative humidity was 79.3% and 72.7% in July of 1997 and 1998, 78.2% and 79.1% in August of 1997 and 1998 during storage on the simple house after pre-drying. Rotting ratio of onion bulb showed higher in 1998 than 1997, but rotting appeared earlier 1997 than 1998. Total rotting rate as influenced by place and days of pre-drying was the lowest on the ventilation house, and highest on the non-ventilation. As the days of pre-drying increase, rotting rate of onion bulbs were lower. As above results, 1 or 2days of pre-drying on the ventilation house and 2 or 3days of pre-drying on the field were recommended to decrease the rotting onion bulb during storage.