• 한국인터넷방송통신학회논문지
• /
• 제19권5호
• /
• pp.107-113
• /
• 2019

본 논문에서는 CR-MMA (Constellation Reduction-Multi Modulus Algorithm) 등화 알고리즘에 adaptive modulus와 adaptive stepsize를 적용하므로서 등화 성능을 개선할 수 있는 Hybrid-CRMMA 알고리즘을 제안한다. CR-MMA 알고리즘은 16-QAM과 같은 nonconstant modulus 신호를 constant modulus 신호로 reduction한 후, 송신 신호의 통계치인 고정 modulus를 이용하여 오차 신호를 발생하므로 기존 MMA의 적응 등화 성능을 개선시키기 위하여 등장하였다. 제안 방식인 Hybrid-CRMMA는 CR-MMA의 constellation reduction 개념에 등화기 출력 신호의 전력에 비례토록 adaptive modulus와 오차 신호의 비선형성을 이용하여 adaptive stepsize를 적용하였으며, 이의 개선된 등화 성능을 컴퓨터 시뮬레이션을 통해 확인한다. 이를 위한 성능 지수로는 등화기 출력 신호 성상도, 수렴 특성을 나타내는 잔류 isi, 최대 찌그러짐, MSE 및 알고리즘의 외부 잡음에 대한 강인성을 나타내는 SER을 사용하였다. 컴퓨터 시뮬레이션 결과 제안 Hybrid-CRMMA가 기존 CR-MMA보다 모든 성능 지수에서 우월함을 확인하였다.

• Steel and Composite Structures
• /
• 제3권3호
• /
• pp.185-198
• /
• 2003

The concept of performance based seismic design has been gradually accepted by the earthquake engineering profession recently, in which the cost-effectiveness criterion is one of the most important principles and more attention is paid to the structural performance at the inelastic stage. Since there are many uncertainties in seismic design, reliability analysis is a major task in performance based seismic design. However, structural reliability analysis may be very costly and time consuming because the limit state function is usually a highly nonlinear implicit function with respect to the basic design variables, especially for the complex large-scale structures for dynamic and nonlinear analysis. Understanding statistical properties of the structural inelastic deformation, which is the aim of the present paper, is helpful to develop an efficient approximate approach of reliability analysis. The present paper studies the statistical properties of the maximum elastoplastic story drift of steel frames subjected to earthquake load. The randomness of earthquake load, dead load, live load, steel elastic modulus, yield strength and structural member dimensions are considered. Possible probability distributions for the maximum story are evaluated using K-S test. The results show that the choice of the probability distribution for the maximum elastoplastic story drift of steel frames is related to the mean value of the maximum elastoplastic story drift. When the mean drift is small (less than 0.3%), an extreme value type I distribution is the best choice. However, for large drifts (more than 0.35%), an extreme value type II distribution is best.

• 호남수학학술지
• /
• 제38권1호
• /
• pp.169-212
• /
• 2016

Entire functions have been investigated so popularly to have been divided into a large number of specialized subjects. Even the limited subject of entire functions is too vast to be dealt with in a single volume with any approach to completeness. Here, in this paper, we choose to investigate certain interesting results associated with the comparative growth properties of iterated entire functions using (p, q)-th order and (p, q)-th lower order, in a rather comprehensive and systematic manner.

• 농업과학연구
• /
• 제37권2호
• /
• pp.271-276
• /
• 2010

In this study, the light-frame wood shear walls according to the sheathing materials was carried out to investigate the shear load performance. Most common sheathing materials are the structural OSB and gypsum board used to consist wall of wood-frame house. Seven different type of specimens are composed of several sheathing materials and shear test was taken to evaluate shear performance by KS F 2154. As a result, shear walls(G12.5/G12.5 and G12.5/OSB) show that maximum shear strength and shear rigidity modulus are 7316N/mm${\cdot}$118.25 N/mm and 11129 N/mm${\cdot}$184.66 N/mm respectively. The shear wall using gypsum board 15mm improve maximum shear strength and shear rigidity modulus about 30%. The shear wall using 15mm gypsum board showed intermediate value in one side specimens. Different types of shear walls could be compared with the shear load performance. Also, nailed joint failure aspects are different to sheathing material and installing method.

• Advances in biomechanics and applications
• /
• 제1권1호
• /
• pp.67-76
• /
• 2014

Bone properties are one of the key components when constructing models that can simulate the mechanical behavior of a mandible. Due to the complexity of the structure, the tooth, ligaments, different bones etc., some simplifications are often considered and bone properties are one of them. The objective of this study is to understand if a simplification of the problem is possible and assess its influence on mandible behavior. A cadaveric toothless mandible was used to build three computational models from CT scan information: a full cortical bone model; a cortical and cancellous bone model, and a model where the Young's modulus was obtained as function of the pixel value in a CT scan. Twelve muscle forces were applied on the mandible. Results showed that although all the models presented the same type of global behavior and proximity in some locations, the influence of cancellous bone can be seen in strain distribution. The different Young's modulus defined by the CT scan gray scale influenced the maximum and minimum strains. For modeling general behavior, a full cortical bone model can be effective. However, when cancellous bone is included, maximum values in thin regions increase the strain distribution. Results revealed that when properties are assigned to the gray scale some peaks could occur which did not represent the real situation.

• Carbon letters
• /
• 제11권4호
• /
• pp.311-315
• /
• 2010

In this work, the effect of glycidyl methacrylate grafted multi-walled carbon nanotubes (GMA-MWCNTs) on the viscoelastic behaviors of polypropylene (PP) based nanocomposites was studied. The GMA-MWCNTs/PP was prepared using a bravender at $200^{\circ}C$ by melt mixing as a function of GMA-MWCNT content. The viscoelastic behaviors of GMA-MWCNTs/PP nanocomposites were measured by a rheometer. It was found that the GMA-MWCNTs were homogeneously dispersed in the PP matrix. The GMA-MWCNTs/PP nanocomposites showed higher storage modulus, loss modulus, and shear viscosity compared to pure PP nanocomposites and the maximum value was shown at 2.0 wt% GMA-MWCNTs loading. These results were probably attributed to the strong interfacial interaction between the GMA-MWCNT and the PP matrix.

• Macromolecular Research
• /
• 제14권3호
• /
• pp.365-372
• /
• 2006

Poly[styrene-b-(ethylene-co-butylene)-b-styrene](SEBS) triblock copolymer was studied by dissolving the ethylene butylene midblock in selective hydrocarbon oils. These oils differ in their aromatic, paraffinic and naphthenic content. Dynamic rheological studies showed that the storage modulus (G') exceeded the loss modulus (G') for all the gels over the entire range of frequency, thereby confirming them as physical gels. However, the behavior of G' and G' as a function of frequency depended primarily on the oil type. The gelation melting temperature decreased drastically with increased oil aromaticity. Small angle X-ray scattering studies revealed that the maximum interdomain interference shifted to a higher angle depending on the composition and type of hydrocarbon oil.

• 대한토목학회논문집
• /
• 제29권2C호
• /
• pp.71-79
• /
• 2009

본 연구에서는 국내 철도 토공노반 재료로 가장 흔히 사용되는 입도조정쇄석, 화강풍화토, 암버럭-토사 혼합 재료에 대해 평균유효주응력과 축변형률의 함수로 표현되는 회복탄성계수 예측모델을 결정하였다. 회복탄성계수 예측모델은 대표적인 동적물성치인 변형률에 따른 전단탄성계수 감소곡선의 표현과 같이 최대영탄성계수와 정규화 영탄성계수 감소곡선으로 구성된다. 평균유효주응력의 함수로 표현되는 최대영탄성계수의 모델인자는 $A_E$와 $n_E$이고, 비선형 영역의 정규화 영탄성계수 감소곡선은 기준변형률(${\varepsilon}_r$)과 곡률계수(a)를 모델인자로 하는 수정 쌍곡선 모델로 표현된다. 제안된 회복탄성계수 예측모델을 검증하기 위해 3차원 다층탄성해석 프로그램(GEOTRACK)을 이용하여 평택 시험 철도노반의 탄성거동을 평가하였고, 화물열차 및 여객열차가 시험구간을 통과할 때 계측한 노반의 수직 탄성변위와 비교하였다. 현장계측은 자갈도상 아래의 재료가 각각 입도조정쇄석과 양질의 화강풍화토인 두 개소에서 수행되었다. 자갈도상 아래에서 계산된 수직 탄성변위는 대략 0.6mm 이내였고 계측 결과와 잘 일치하였다. 본 연구를 통해 제안된 회복탄성계수 예측모델이 열차하중에 의한 노반의 탄성거동을 적절히 표현하고 있음을 확인하였다.

• 구강회복응용과학지
• /
• 제32권3호
• /
• pp.169-175
• /
• 2016

목적: 본 연구의 목적은 수종의 레진계 치아고정 재료의 굴곡강도와 탄성계수를 비교 분석하는 것이다. 연구 재료 및 방법: 레진계 치아고정 재료로 Super-Bond C&B (SB), G-FIX (GF), G-aenial Universal Flo (GU), Filtek Z350 XT (FZ)를 이용하여 각 군당 15개씩 총 60개의 시편을 제작하였다. 3점 굽힘 시험으로 측정된 값에 따라 굴곡강도와 탄성계수를 계산하였다. 실험값은 One-way ANOVA test로 분석하고, Scheffe's test로 사후 검정하였다. 결과: 본 연구의 결과 SB는 다른 재료들과 비교 시 가장 낮은 굴곡강도를 보였으며 GF, GU, FZ는 비슷하게 높은 굴곡강도를 보였다. 탄성계수의 경우 SB가 가장 낮은 값을 보였고 GF는 SB보다는 높지만 GU와 FZ보다는 낮은 탄성계수를 보였으며 GU와 FZ는 유의하게 높은 탄성계수를 보였다. 결론: 동요치 고정을 목적으로 새로 개발된 GU (G-FIX)는 유동성 복합 레진과 수복용 복합 레진과 같이 높은 강도를 보이며 잘 파절되지 않으면서도 상대적으로 유연한 성질을 보여 동요치 고정에 유리할 것으로 사료된다.

• Communications for Statistical Applications and Methods
• /
• 제8권2호
• /
• pp.357-366
• /
• 2001

The present paper develops a method to check the propriety of link functions for binary data. In order to parameterize a certain type of goodness of the link, a family of link functions indexed by a shape parameter is proposed. I first investigate the maximum likelihood estimation of the shape parameter as well as regression parameters and then derive their large sample behaviors of the estimators. A score test is considered to evaluate the goodness of the current link function. For illustration, I employ two families of power transformations, the modulus transformation by John and Draper (1980) and the extended power transformation by Yeo and Johnson (2000), which are appropriate to detect symmetric and asymmetric inadequacy of the selected link function. respectively.