• Journal of Biosystems Engineering
• /
• v.27 no.3
• /
• pp.203-210
• /
• 2002

In this study, the leveling control system for a tractor has been developed. The experimental model showed that the implementation of the proposed hydraulic control system fur the prototype design of a slope land tractor was feasible. The front axle was designed as a center pin type and the rear axle was designed as a trailing arm type. The leveling control of the body on the slope land was accomplished by controlling the height of the right and left trailing arms using the electronic controlled hydraulic cylinder. The maximum leveling control angles were ${\pm}$15$^{\circ}$ for roll angle and 7$^{\circ}$far pitch angle. The front and rear wheel drives were transmitted by gears from the main shaft to the final drive. The adaptability of the hydraulic control system was tested and investigated by analyzing the system response in time and frequency domain. The hydraulic control system on a step input showed a linearly increasing trend without any overshoot state. The hydraulic control system on a frequency input showed a little phase differences and gain drops within the range of 0.3Hz.

• Journal of Broadcast Engineering
• /
• v.20 no.4
• /
• pp.489-496
• /
• 2015

In this paper, a new weighted prediction scheme is proposed to improve the coding efficiency for video scenes containing brightness variations. Conventional weighted prediction is applied by the reference picture and use only one weighted parameter set. Thus, it is only useful for GBV(Glabal Brightness Variation). In order to solve this problem, the proposed algorithm use three kind of schemes depending on situation. Experimental results show that maximum coding efficiency gain of the proposed method is up to 10.2% in luminance. Average computional time complexity is increased about 163% in encoder and about 101% in decoder.

• Journal of Internet Computing and Services
• /
• v.12 no.2
• /
• pp.1-8
• /
• 2011

In this paper, we propose an effective method for cooperative spectrum sensing in cognitive radios where cognitive user(CR) with the highest reliability sensing data is only selected and allowed to report its local decision to FC as only decision making node. The proposed scheme enables CR users to implicitly compare their sensing data reliabilities based on their likelihood ratio, without any collaboration among cognitive radio users. Due to the mechanism, the proposed cooperative scheme can achieves a high spectrum sensing performance while only requiring extremely low cooperation resources such as signaling overhead and cooperative time in comparison with other existing methods such as maximum ratio combination (MRC) based, equal gain combination (EGC) based and conventional hard combination based cooperative sensing methods.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.220-226
• /
• 2011

We have proposed a new method to accurately predict the resonance of Fabry-Perot Cavity (FPC) antennas enclosed with conducting side walls. When lateral directions of an FPC antenna are not blocked with metallic walls, the conventional technique is accurate enough to predict the resonance of the FPC antenna. However, when the FPC antenna has side walls, especially for case with only a short distance between the walls, the conventional prediction method yields an inaccurate result, inevitably requiring a tedious, time-consuming tuning process to determine the correct resonant height to provide the maximum antenna gain in a target frequency band using three-dimensional full-wave computer simulations. To solve that problem, we have proposed a new resonance prediction method to provide a more accurate resonant height calculation of FPC antennas by using the well-known resonance behavior of a rectangular resonant cavity. For a more physically insightful explanation of the new prediction formula, we have reinvestigated our proposal using a wave propagation characteristic in a hollow rectangular waveguide, which clearly confirms our approach. By applying the proposed technique to an FPC antenna covered with a partially reflecting superstrate consisting of continuously tapered meander loops, we have proved that our method is very accurate and readily applicable to various types of FPC antennas with lateral walls. Experimental result confirms the validness of our approach.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.320-328
• /
• 2006

Using biometrics to verify a person's identity has several advantages over the present practice of personal identification numbers (PINs) and passwords. To gain maximum security in a verification system using biometrics, the computation of the verification as well as the storing of the biometric pattern has to take place in a smart card. However, there is an open issue of integrating biometrics into a smart card because of its limited resources (processing power and memory space). In this paper, we propose a speaker verification algorithm using a support vector machine (SVM) with a very few features, and implemented it on a 32-bit smart card. The proposed algorithm can reduce the required memory space by a factor of more than 100 and can be executed in real-time. Also, we propose a hardware design for the algorithm on a field-programmable gate array (FPGA)-based platform. Based on the experimental results, our SVM solution can provide superior performance over typical speaker verification solutions. Furthermore, our FPGA-based solution can achieve a speed-up of 50 times over a software-based solution.

• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.86-95
• /
• 2015

An active clamp high step-up boost converter with a coupled inductor is proposed in this paper. In the proposed strategy, a coupled inductor is adopted to achieve a high voltage gain. The clamp circuit is included to achieve the zero-voltage-switching (ZVS) condition for both the main and clamp switches. A rectifier composed of a capacitor and a diode is added to reduce the voltage stress of the output rectifier diode. As a result, diodes with a low reverse-recovery time and forward voltage-drop can be utilized. Since the voltage stresses of the main and clamp switches are far below the output voltage, low-voltage-rated MOSFETs can be adopted to reduce conduction losses. Moreover, the reverse-recovery losses of the diodes are reduced due to the inherent leakage inductance of the coupled inductor. Therefore, high efficiency can be expected. Firstly, the derivation of the proposed converter is given and the operation analysis is described. Then, a steady-state performance analysis of the proposed converter is analyzed in detail. Finally, a 250 W prototype is built to verify the analysis. The measured maximum efficiency of the prototype is 95%.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.1
• /
• pp.48-54
• /
• 2017

In this paper, hysteresis voltage control method is proposed to an unidirectional inverter control for piezoelectric load. Piezoelectric load has electrically RC characteristic, and is driven by the inverter to control the output voltage waveform. When controling the output waveform by PI control, appropriate gains need to be selected. However, hysteresis control may minimize the output distortion because it has maximum proportional gain. In addition, Hysteresis control algorithm has simple structure to realize and the response is fast. Although the switching frequency of the inverter by hysteresis control varies, the switching frequency for the piezoelectric load is lower than that by PI control for equivalent performance. In particular, on implementing the algorithm using FPGA, the algorithm can be implemented in fewer pabrics and the processing time can be reduced. The superiority of the proposed hysteresis voltage control was proved for piezoelectric load through simulation and experiment.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.5 no.9
• /
• pp.1573-1595
• /
• 2011

In this paper, the outage performance of multiuser multiple-input single-output (MISO) systems exploiting joint spatial and multiuser diversities is investigated for Rayleigh fading channels with outdated feedback. First, we derive closed-form exact outage probabilities for the joint diversity schemes that combine user scheduling with different spatial diversity techniques, including: 1) transmit maximum-ratio combining (TMRC); 2) transmit antenna selection (TAS); and 3) orthogonal space-time block coding (OSTBC). Then the asymptotic outage probabilities are analyzed to gain more insights into the effect of feedback delay. It is observed that with outdated feedback, the asymptotic diversity order of the multiuser OSTBC (M-OSTBC) scheme is equal to the number of transmit antennas at the base station, while that of the multiuser TMRC (M-TMRC) and the multiuser TAS (M-TAS) schemes reduce to one. Further by comparing the asymptotic outage probabilities, it is found that the M-TMRC scheme outperforms the M-TAS scheme, and the M-OSTBC scheme can perform best in the outage regime of practical interest when the feedback delay is large. Theoretical analysis is verified by simulation results.

• Wind and Structures
• /
• v.32 no.5
• /
• pp.405-421
• /
• 2021

To gain insight into the wind-induced safety concerns associated with attached tower cranes during the construction of super-tall buildings, a 606 m level frame-core tube super-tall building is selected to investigate the wind-induced vibration response and fragility of an outer-attached tower crane at all stages of construction. The wind velocity time history samples are artificially generated and used to perform dynamic response analyses of the crane to observe the effects of wind velocity and wind direction under its working and non-working resting state. The adverse effects of the relative displacement response at different connection supports are also identified. The wind-resistant fragility curves of the crane are obtained by introducing the concept of incremental dynamic analysis. The results from the investigation indicate that a large relative displacement between the supports can substantially amplify the response of the crane at high levels. Such an effect becomes more serious when the lifting arm is perpendicular to the plane of the connection supports. The flexibility of super-tall buildings should be considered in the design of outer-attached tower cranes, especially for anchorage systems. Fragility analysis can be used to specify the maximum appropriate height of the tower crane for each performance level.

• Geomechanics and Engineering
• /
• v.18 no.3
• /
• pp.277-289
• /
• 2019

In this study, an innovative anchoring approach has been developed dealing with all relevant aspects in consideration of previous works. An ultimate pulling force calculation of anchor is presented from a geotechnical point of view. The proposed umbrella anchor focuses not only on the friction resistance capacity, but also on the axial capacity of the composite end structure and the friction capacity occurring around the wedge. Even though the theoretical background is proposed, in-situ application requires high-level mechanical design. Hence, the required parts have been carefully improved and are composed of anchor body, anchor cap, connection brackets, cutter vanes, open-close ring, support elements and grouting system. Besides, stretcher element made of aramid fabric, interior grouting system, guide tube and cable-locking apparatus are the unique parts of this design. The production and placement steps of real sized anchors are explained in detail. Experimental results of 52 pullout tests on the weak dry soils and 12 in-situ tests inside natural soil indicate that the proposed approach is conservative and its peak pullout value is directly limited by a maximum strength of anchored soil layer if other failure possibilities are eliminated. Umbrella anchor is an alternative to conventional anchor applications used in all types of soils. It not only provides time and workmanship benefits, but also a high level of economic gain and safe design.