• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.10
• /
• pp.825-832
• /
• 2002

The present study investigated the enhancement of the absorption performance by the spring wrapped around the outer surface of the vertical falling film absorber tube. Heat and mass transfer enhancements were experimentally investigated, and flow visualization was performed to observe the wettability and flow pattern of the solution. The key experimental parameters were spring diameter (0.5, 1.0 mm) and spring pitch (1, 3, 10 mm), film Reynolds number (50~150), and concentration of LiBr-$H_2O$ solution (55, 60, 65 wt%). As the spring diameter was increased, the absorption mass flux, Sherwood number, Nusselt number, heat flux, and heat transfer coefficient were increased The Nusselt and Sherwood numbers showed the maximum at the spring pitch of 3mm, and the ratio of pitch to diameter of approximately 3 and 6 for the spring diamter of 0.5 mm, respectively.

• Macromolecular Research
• /
• v.17 no.2
• /
• pp.79-83
• /
• 2009

The oral delivery of heparin is the preferred therapy in the treatment of patients with a high risk of deep vein thrombosis and pulmonary embolism. New conjugates of heparin and sodium deoxycholate were synthesized in order to enhance the heparin absorption in the GI tract. After oral administration of DOC-heparin, the concentration in anti-FXa assay was increased with increasing amount of coupled DOC. The maximum concentration of DOC-heparin VIII conjugate was $3.3{\pm}0.5\;IU/mL$ at an oral dose of 10 mg/kg, which was 3-fold higher than the baseline level. Finally, DOC coupled to heparin greatly enhanced the absorption of heparin in the GI tract, and this enhancing effect was not induced by changing the tissue structure of the GI wall.

• Archives of Pharmacal Research
• /
• v.19 no.3
• /
• pp.183-190
• /
• 1996

There are a wide variety of semi-solid ointments used for healing the skin diseases, whose therapeutic and skin penetration abililties may greatly differ from one another depending on the compositions of ointment vehicles. A computer optimization technique was applied to obtain the optimum formula of o/w type ointment giving the in vitro maximum absorption rate through hairless rat skin membrane. Some of the formulations were selected to find out a relationship between skin penetration of ointment and its Theological characteristics. The experimental value of absorption rate obtained from the ointment by optimum formula agreed well with the theoretical value obtained from a polynomial regression analysis, Three kinds of ointments selected among 15 formulations were obtained with a concentric cylinder type rheometer (Model; Rheolab SM-HM Physica, Germany) at 20, 30, 40 and $50^{\circ}C$ for rheograms of rhelolgical properties of o/w type ointments. As the temperature was raised, all products showed a decrease in both shear stress and yield values. The higher skin penetration, the lower shear stress showed.

• The Korean Journal of Food And Nutrition
• /
• v.7 no.4
• /
• pp.332-337
• /
• 1994

The antioxidant activity of solvent extracts isolated from barley leaves was investigated by measuring peroxide value. The fractions of methanol extract obtained from preparative TLC was also studies, with UV-Visible spectrum, total phenol contents and hydrogen donating ability(HDA) The antioxidant activity of various solvent extracts was, in decreasing order, methanol> ethyl ether> methylene chloride $\geq$ ethyl acetate $\geq$acetone> hexane. The antioxidant activity of the fractions of methanol extract was, in decreasing order, fraction 2> fraction 3> fraction 1 and their activity was all superior to that of tocopherol at 500 ppm level. All fraction(1, 2 and 3) exhibited a strong UV absorption at 280 m which would be specifically produced by phenolic compound. UV absorption at 280 m of fraction 2 was greater than those of fraction 1 and 3. In the visible spectrum of these fractions, the maximum .absorption wavelengths of fraction 1, 2 and 3 were 660, 460 and 460 m, respectively. Antioxidant activity of barley leaves seemed to be due to the flavonoids containing phenolic group by UV spectrum and total phenol content.

• Structural Engineering and Mechanics
• /
• v.70 no.2
• /
• pp.153-168
• /
• 2019

In this paper, energy absorption characteristics of circular windowed tubes with different section shapes (circular, ellipse, square, hexagon, polygon and pentagon) are investigated numerically and experimentally. The tube possesses the same material, thickness, height, volume and average cross sectional area which are subjected under axial and oblique quasi-static loading conditions. Numerical model was constructed with FE code ABAQUS/Explicit, the obtained outcome of simulation is in good matching with the experimental data. The energy absorbed, specific energy absorption, crash force efficiency, peak and mean loads along with the collapse modes with their initiation point of simple and windowed tubes were evaluated. The technique for order of preference by similarity ideal solution (TOPSIS) approach was employed for assessing their overall crushing performances. The obtained results confirm that efficacy of crash force indicators have improved by introducing windows and tubes with pentagonal and circular windows achieves the maximum ranking about 0.528 and 0.517, it clearly reveals the above are best window shapes.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.2
• /
• pp.73-78
• /
• 2024

This study presents a real-time method that uses Laser Absorption Spectroscopy (LAS) to measure exhaust gas temperatures in turbulent flow fields. It was possible to measure temperature by passing a laser beam through the exhaust gas in a grid pattern, and obtain a temperature distribution image through time series analysis at 0.1 second intervals. Temperature image resolution has been improved with CT reconstruction algorithms. Estimating maximum temperature values and locations enabled 2D temperature analysis, surpassing single-point methods like thermocouples. The accuracy of LAS measurements was evaluated by comparison with thermocouple measurements. This approach will contribute to automotive technology and environmental protection by providing reliable temperature data for interpreting turbulent temperature distributions.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.457-462
• /
• 2010

Sound absorption capability and bending strength of laminated ship-building plywood waste of maple and melanti wood were estimated. Sound absorption coefficients of wood had been measured by the two microphone transfer function method and bending strength examined by three point loading. The maximum strength in bending of laminated ship-building plywood waste of maple and melanti wood were 534 and 414 kgf/$cm^2$, respectively. The sound absorption coefficients of laminated ship-building plywood waste were higher than mongolian oak and fiber board, well used construction material. Especially, in the case of laminated ship-building plywood waste of melanti wood, average sound absorption coefficient was about 0.25. It was surmised that the laminated ship-building plywood waste can be used as interior materials because of its good mechanical and sound absorption properties.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.6
• /
• pp.588-594
• /
• 2000

Structural changes of an iron phthalocyanine (FePC) monolayer induced by adsorption and externally applied potential on high area carbon surface have been investigated in situ by iron K-edge X-ray absorption fine structure (XAFS) in 0.5 M $H_2S0_4.$ Fine structures shown in the X-ray absorption near edge structure (XANES) for microcrystalline FePC decreased upon adsorption and further diminished under electrochemical conditions. Fe(II)PC(-2) showed a 1s ${\rightarrow}$ 4p transition as poorly resolved shoulder to the main absorption edge rather than a distinct peak and a weak 1s ${\rightarrow}$ 3d transition. The absorption edge position measured at half maximum was shifted from 7121.8 eV for Fe(lI)PC(-2) to 7124.8 eV for $[Fe(III)PC(-2)]^+$ as well as the 1s ${\rightarrow}$ 3d pre-edge peak being slightly enhanced. However, essentially no absorption edge shift was observed by the 1-electron reduction of Fe(Il)PC(-2), indicating that the species formed is $[Fe(II)PC(-3)]^-$. Structural parameters were obtained by analyzing extended X-ray absorption fine structure (EXAFS) oscillations with theoretical phases and amplitudes calculated from FEFF 6.01 using multiple-scattering theory. When applied to the powder FePC, the average iron-to-phthalocyanine nitrogen distance, d(Fe-$N_p$) and the coordination number were found to be 1.933 $\AA$ and 3.2, respectively, and these values are the same, within experimental error, as those reported ( $1.927\AA$ and 4). Virtually no structural changes were found upon adsorption except for the increased Debye-Wailer factor of $0.005\AA^2$ from $0.003\AA^2.$ Oxidation of Fe(II)PC(-2) to $[Fe(III)PC(-2)]^+$ yielded an increased d(Fe-Np) (1 $.98\AA)$ and Debye-Wailer factor $(0.005\AA^2).$ The formation of $[Fe(II)PC(-3)]^-$, however, produced a shorter d(Fe-$N_p$) of $1.91\AA$ the same as that of crystalline FePC within experimental error, and about the same DebyeWaller $factor(0.006\AA^2)$.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.2
• /
• pp.33-39
• /
• 2010

The moisture absorption properties such as diffusion coefficient and moisture content ratio of liquid type epoxy resin systems with the filler were investigated. Bisphenol A type and Bisphenol F type epoxy resin, Kayahard MCD as hardener and 2-methylimidazole as catalyst were used in these epoxy resin systems. The nano-sized spherical type fused silica as filler were used in order to study the moisture absorption properties of these liquid type epoxy encapsulant according to the change of filler size. The temperature of glass transition (Tg) of these epoxy resin systems was measured using Dynamic Scanning Calorimeter (DSC), and the moisture absorption properties of these epoxy resin systems according to the change of time were observed at $85^{\circ}C$ and 85% relative humidity condition using a thermo-hygrostat. The diffusion coefficients in these systems were calculated in terms of modified Crank equation based on Ficks' law. An increase of Tg and diffusion coefficient with filler size in these systems can be observed, which are attributed to the increase of free volume with Tg. The change of maximum moisture absorption ratio according to the filler size and filler content cannot be observed; however, the diffusion coefficients of these systems decreased with filler content. The diffusion via free volume is dominant in the epoxy resin systems with low nano-sized filler content; however, the diffusion with the interaction of absorption according the increase of the filler surface area is dominant in the liquid type epoxy encapsulant with high nano-sized filler content.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.133-134
• /
• 1982

This experiment has been made to investigate the absorption of watersoluble zinc chloride by Pinus densiflora S. et Z. at different moisture content, under soaking process, to decide the optimum content condition for the maximum absorption of zinc chloride by the wood tested and to investigate the concentration of zinc chloride affecting each moisture content of wood. Material was cut in the Dept. of Forest, College of Agr. S.N.U. Suwon, Korea. Sample was divided into sap and heartwood group and cut $2{\times}2{\times}2\;cm$ in size, having exact three dimensions, using the part of D.B.H. The numbers of sample were 20 pieces for each moisture content condition for both sap and heartwood. Especially, the samples were protected from exposure to keep moisture content in green condition. The ranges of moisture content tested were as the table 3 and 4. The conclusions were as follows: 1. With 3% zinc chloride solution, the rate of absorption decreased with the time increased, if the air seasoned Korean red pine (Pinus densiflora S. et Z.) was treated in steeping process. Initial absorption for 30 minutes was more than 50% of total absorpon for 24 hours. 2. Rate of absorption was same under the green condition, while rate of absorption under the moisture content 7 to 30% varied. 3. Although it was not quite proportional change in the absorption with the difference of moisture content, the great change in the absorption occured by seasoning. With exception sap green condition, sapwood twice more permeable than the heartwood in the oven dried condition and it has been observed the nearly same amount of absorption at the moisture content of 7%, 10% and 15% respectively in heartwood. 4. It was better from water in wood from view-point of absorption of zinc chloride solution, but it was difficult practically to obtain the smallest moisture content, and then it was decided that values of allowable moisture content, on the basis of mean absorption, were 15% to 20% in the sapwood, and in the heartwood, 10% to 15%. The mean absorption for each moisture content in the sap and the heartwood were as following. 5. In general, the concentration of zinc chloride after steeping was nearly same between moisture content and sap and heartwood respectively.