• Journal of the Korean Data and Information Science Society
• /
• 제16권2호
• /
• pp.263-270
• /
• 2005

The reliability guarantee insurance policy for parts and materials was introduced to the market in 2003. This policy indemnifies manufactures for the repair/failure costs, recall expenses. In this paper, owing to the nature of the policy, we propose a new rate-making system considering the type of product and industry, quality control circumstances, record of guarantee performance, and exposures.

• 소성∙가공
• /
• 제9권6호
• /
• pp.561-566
• /
• 2000

Recently, the hydroforming technology has been recognized as a general technique in manufacturing industry, especially in automotive industry. Hydroforming is applied to increase strength, and to decrease weight, cost and parts. Hydroforming is based on the inflation of, for Instance, a tube, coupled with axial or radial compression and by subsequent expansion and sizing against the die wall. Expansion, axial feeding, calibration are important parameters in this process. In this paper, the effects of various parameters such as internal pressure, axial feeding and friction on hydroforming of automotive bumper rail have been considered.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.247-250
• /
• 2006

The growing demand for more fuel-efficient vehicles to reduce energy consumption and air pollution is a challenge for the automotive industry. The characteristic properties of aluminum, high strengrth stiffness to weight ratio, good formability, good corrosion resistence, and recycling potential make it the ideal candidate to replace heavier materials in the car to respond to the weight resuction demand within the automotive industry. In this paper, A series of compression test was carried out to find the flow stress of A6082 at 300, 400 and $500^{\circ}C$, then we tried to estimate weldability, extrusion load and effective stress of die in the aluminum extrusion process through the 3D FE simulation at non-steady state for aluminum automotive parts.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.585-589
• /
• 2023

Unlike general carbon steel, stainless steel's mechanical properties change depending on the content of chromium and nickel. In this study, since stainless steel for high-temperature pressure container parts is used as shafts, the fatigue strength and fatigue limit of the materials were evaluated using a rotational bending fatigue test. Meanwhile, fatigue analysis was conducted under the same conditions as the specimen for structural analysis and fatigue analysis of stainless steel for high-temperature pressure container parts. Using the fatigue analysis results, we tried to derive the life of the material and the safety factor for each part. As a result of performing a fatigue test by processing a specimen for the fatigue test of A182 F6A stainless steel, the fatigue limit was 548 MPa. The ratio between the tensile strength and fatigue limit of the material was 0.545, representing 54.5% of the tensile strength.

• 자동차안전학회지
• /
• 제8권4호
• /
• pp.24-30
• /
• 2016

In Korea, the Vehicle Dismantler and Recycler industry is supervised by the Ministry of Land, Infrastructure and Transport under the Automobile Management Act. Also, Korean Automotive recycling businesses are supervised by the Minister of Environment under the Resource Recirculation Act. The main concern of the Minister of Environment is how the wastes from Dismantled vehicles will be environmentally removed, stored, treated, recycled or disposed. In 2000, the European Union (EU) adopted the End-of-Life Vehicles Directive (2000/53/EC) which required Members to ensure the collection, treatment and recovery of end-of-life vehicles (ELVs). The Directive, the most tightly regulated and precautionary legal systems, required that the last owner of a vehicle could drop off the ELV at an authorized treatment facility and that the producers of the ELV should pay the cost of the program. The adoption of the ELVs directive has led the development of Automotive Dismantler and Recycler networks to reuse, refurbish, remanufacture, recycle and recover parts and materials embedded in ELVs. Also, the ELVs directive which has had an insignificant impact on Korean manufacturers has strong presence in the European market and has been successfully externalized on them. The Korean manufacturers not only achieve the 85% recycling target set by the ELVs directive but also meet the Extended Producer Responsibility (EPR) which requires manufacturers to contribute dismantling process. In order to improve the Korean vehicle dismantling and recycling system, the Automobile Management Act and the Resource Recirculation Act should be harmonized. Particularly the roles of the Ministry of Land, Infrastructure and Transport and the Minister of Environment should be sharply divided. Like Japan, the ELV management needs to be highly centralized, regulated, and controlled by the ministry specialized in Vehicle, namely the Ministry of Land, Infrastructure and Transport and the sub organizations. Like EU Members, recovery, reuse, and recycling must be distinguished. Recovery is defined as the final productive use of the parts and materials embedded in ELVs, which includes reuse and remanufacture of parts and recycling of the other materials. Dismantling process and reuse and remanufacture of parts must be governed by the Ministry of Land, Infrastructure and Transport. For environmental recycling or disposal of waste materials, such as CFCs, glass and plastic material, and toxic substances, governmental financial support system should be in place.

• Corrosion Science and Technology
• /
• 제11권6호
• /
• pp.232-241
• /
• 2012

This work focused on corrosion of carbon steel bolted GECM/Al parts in tap water and NaCl solutions. In tap water and NaCl solutions, open circuit potential of GECM and its potentials in a series of carbon steel bolt>Ti>Al became active. Regardless of test materials, open circuit potentials in tap water were noble, and increasing NaCl concentration, its potentials became active. Immersion test of single specimen showed that no corrosion occur in Ti and GECM. In tap water, carbon steel bolt didn't show red corrosion product and in chloride solutions, corrosion rate in 1% NaCl solution was greater than its rate in 3.5% NaCl solution and red corrosion product in 1% NaCl solution was earlier observed than that in 3.5% NaCl solution. It seems that this behavior would be related to zinc-coatings on the surface of carbon stee l bolt. On the other hand, aluminium was corroded in tap water and chloride solutions. Corrosion of aluminium in tap water was due to the presence of chloride ion in tap water by sterilizing process.

• Composites Research
• /
• 제12권5호
• /
• pp.23-30
• /
• 1999

Fiber reinforced composite materials are widely used in automotive industry to produce parts that are large, thin, lightweight, strong and stiff. It is very important to know a charge shape in order to have good products in the compression molding. In particular, the product such as a bumper beam is composed of the random and unidirectional fiber mats. The characteristics of flow fronts such as a bulging phenomenon for random mat and unidirectional fiber mat and slip parameters are studied numerically. And the effects of viscosity ratio and stack type on mold filling parameters are also discussed.

• Advanced Composite Materials
• /
• 제16권2호
• /
• pp.135-149
• /
• 2007

In the automobile industry, structural health monitoring of fiber reinforced polymer composite parts is a widespread need for maintenance before breakdown of the functional elements or a complete vehicle. High performance sensors are generally used in many of the structural health monitoring operations. Within this study, a carbon fiber sewing thread has been used as a low cost laminate failure sensing element. The experimentation plan was set up according to the electrical conductance and flexibility of carbon fiber threads, advantages of preforming operations, and sewing mechanisms. The influence of the single thread damages by changing the electrical resistance and monitoring the impact location by using carbon thread sensors has been performed. Innovative utilization of relatively cost-effective carbon threads for monitoring the delamination of metallic inserts from the basic composite laminate structure is a highlighting feature of this study.

• 소성∙가공
• /
• 제17권2호
• /
• pp.130-134
• /
• 2008

Resource and energy saving is a very important practice for the future as well as for today. Weight saving of structural parts, which are formed by extrusion, plays a key role in manufacturing field. The cross-sections of extruded parts with industrial aluminum are constant in the axial direction by conventional extrusion method. Especially, these aluminum parts used and manufactured in the car industry need other processes to vary the cross-section in the axial direction. However, applications of these parts are often limited by high cost. If the cross-section of the parts is variable by only extrusion with newly developed method, the application of extruded aluminum parts will actually increase. Therefore, a new CNC extruder that can control the section area of a car part was invented for the first time in the nation. Using the extrusion machine, the experiment was performed to validate its workability during the variable section extrusion process. Also, numerical analysis was carried out to investigate the flow mode with different speeds of main ram and various pocket shapes of a die-set in the variable section extrusion process.

• 한국경영과학회:학술대회논문집
• /
• 한국경영과학회 2007년도 추계학술대회 및 정기총회
• /
• pp.43-57
• /
• 2007

This paper considers the technological competitiveness of aircraft infra industries that are bases of the aircraft industry development in Korea. We performed focus group interviews to aircraft industry specialists and classified the aircraft infra industries by eight fields: metallurgical assembly, general machinery, precision instruments, materials & parts, communication appliances, computer, semi-conductor/ electronic component, electronics. Through the United States patents analysis for the G7 countries and Korea during 1995-2006, we identified the technological specificities and competences of each country. RTA(Revealed Technology Advantage) index and CII(Current Impact Index) are used to examine the technological specificity and technological competence respectively. Finally, we introduced TCI(Technological Competitiveness Index) which could reflect quantitative level as well as qualitative level of patents for each aircraft infra industry. The results show that Korea has occupied the technological competitiveness in the semi-conductor and electronic component industry out of eight aircraft infra industries, and achieved a competitive edge in communication appliance industry in the mid 2000s.