• Composites Research
• /
• v.36 no.5
• /
• pp.355-360
• /
• 2023

Epoxy-based carbon fibers reinforced plastic (CFRP) exhibit limitations in their suitability for industrial applications due to high brittleness characteristics. To address this challenge, extensive investigations are underway to enhance their toughness properties. This research focuses on evaluating the toughening mechanisms achieved by Polyamide 6 particles(p-PA6) and Carboxyl-Terminated Butadiene-Acrylonitrile (CTBN) elastomer, with a specific emphasis on utilizing minimal additive quantities. The study explores the impact of varying concentrations of p-PA6 and CTBN additives, namely 0.5, 1, 2.5, and 5 phr, through comprehensive Mode I fracture toughness and tensile strength analyses. The inclusion of p-PA6 demonstrated improvements in toughness when introduced at a relatively low content of 1phr. This improvement manifested as a sustained fracture behavior, contributing to enhanced toughness, while simultaneously maintaining the material's tensile strength. Furthermore, the investigation revealed that the incorporation of p-PA6 affected in particle aggregation, thus influencing the overall toughening mechanism. Incorporation of CTBN, an elastomeric modifier, exhibited a pronounced increase in fracture toughness at higher concentrations of 2.5 phr and beyond. However, this increase in toughness was accompanied by a reduction in tensile strength, resulting in fracture behavior similar to conventional CFRP exhibiting brittleness. The synergy between pPA6, CTBN and CFRP appeared to marginally enhance tensile strength under specific content conditions. As a result of this study, optimized conditions for the application of the p-PA6, CTBN toughening technology have been identified and established.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.437-441
• /
• 2006

The red emitting OLEDs using $Alq_3$:Rubrene-GDI4234 phosphors have been fabricated and characterized . In the device fabrication, 2- TNATA [4,4',4' - tris (2- naphthylphenyl - phenylamino ) - tripheny lamine] as the hole injection material and NPB [N,N'-bis (1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] as the hole transport material were deposited on the ITO(indium tin oxide)/glass substrate by vacuum evaporation. And then, red color emissive layer was deposited using $Alq_3$ as the host material and Rubrene(5,6,11,12-tetraphenylnaphthacene)-GDI4234 as the dopants. finally, small molecule OLEDs with structure of ITO/2-TNATA/NPB/$Alq_3$:Rubrene-GDI4234/$Alq_3$/LiF/Al were obtained by in-situ deposition of $Alq_3$, LiF and Al as the electron transport material, electron injection material and cathode, respectively. Red OLEDs fabricated in our experiments showed the color coordinate of CIE(0.65, 0.35) and the maximum power efficiency of 2.1 lm/W at 7 V with the peak emission wavelength of 632 nm.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.625-627
• /
• 2007

We demonstrated high power efficiency and long lifetime in organic light-emitting diode (OLED) using new electron transport materials (ETMs). Electroluminescent device with these ETMs showed lower driving voltage than that with $Alq_3$. The device lifetime with a new ETM was 2 times longer than that with $Alq_3$.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.1
• /
• pp.72-79
• /
• 1998

Journal of the Korean Society of Clothing and Textiles Vol. 22, No. 1 (1998) p. 72∼79 The purpose of this study was to investigate the effects of geometrical structure and fiber type on the water vapor transport properties of nonwoven batting materials. Two types of fiber were used such as polyester and wool. Correlation between physical properties of nonwovens and water vapor transport rate was analyzed by Pearson Correlation. Steady and dynamic state water vapor transport properties were measured by absorption, evaporation and cobaltots chloride method respectively. The results were as follows: 1) In geometrical structure, thickness of nonwovens was effected on absorption and evaporation rate and air permeability was more influencing factor on water vapor transport rate than porosity. There were no decreasing of water vapor transport rate in hydrophilic fiber at high relative humudity. 2) The hydrophilicity of fiber affected steady and dynamic state water vapor permeabilities and wool nonwoven showed higher water vapor transport rate than polyester at high relative humidity. 3) Thickness showed higher correlation coefficient with water vapor transport rate than other physical properties of nonwovens.

• Journal of Biosystems Engineering
• /
• v.43 no.3
• /
• pp.194-201
• /
• 2018

Purpose: The objective of this study was to propose a formula for the theoretical grain mean transport velocities of an elliptically moving oscillator by modifying the grain mean transport velocity formula applied to linear motion and to compare the calculated values with the experimental values of grain mean transport velocity. Methods: The values of the throwing index ($K_v$) and the maximum horizontal velocities for various positions on the elliptical oscillator were obtained using kinematic analysis. To obtain the actual grain transport velocity, the mean transport velocities of perilla grains at six positions on the sieve surface were measured using a high-speed camera and compared with the theoretical values. The cam with an eccentric bearing on the oscillator was designed to be eccentric by 1.6 cm so that the lengths of the major axis of the elliptical motion were 3.2-3.6 cm. The material used in the experiments was perilla grain. Results: The experimental result was consistent with the theoretical value calculated using the proposed formula ($R^2$ is 0.80). It is considered that the angle difference between the maximum accelerations in the directions vertical and horizontal to the sieve has as much influence on the grain mean transport velocity as the value of Kv itself. Conclusions: It was possible to theoretically obtain the grain mean transport velocities through a screening device in elliptical motion by modifying the formula of the grain mean transport velocities used in linear motion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.497-500
• /
• 2001

Due to their better photosensitivity in X-ray, the amorphous selenium based photoreceptor is widely used on the X-ray conversion materials. It was possible to control the charge carrier transport of amorphous selenium by suitably alloying a-Se with other elements(e.g. As, Cl). The charge transport properties of amorphous Selenium is decided on hole which is induced from metal to selenium in metal-selenium junction and which is transferred in a-Se bulk. This phenomenon is resulted of changing electric field owing to increasing of space charge by deep trap of a-Se bulk. In this paper, We dopped the chlorine to compensate deep hole trap and deposited blocking layer using dielectric material to prevent from increasing space charge for injection charge between metal electrode and a-Se layer. We compared space charge and the decreasing of trap density through measuring dark and photo current. 缀Ѐ㘰〻ሀ䝥湥牡氠瑥捨湯汯杹

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.6
• /
• pp.250-254
• /
• 2007

Applying the moving photo-carrier grating(MPG) technique and time-of-flight(TOF) measurements, we studied the transport properties of stabilized amorphous selenium typical of the material used in direct conversion X-ray imaging devices. For MPG measurement, we obtained electron and hole mobility and the recombination lifetime of $\alpha-Se$ films with arsenic(As) additions. We found an apparent increase in hole drift mobility and recombination lifetime, especially when 0.3 % As was added into $\alpha-Se$ film, whereas electron mobility decreased with the addition of As due to the defect density. For TOF measurement, a laser beam with pulse duration of 5 ns and wavelength of 350 nm was illuminated on the surface of $\alpha-Se$ with a thickness of 400 ${\mu}m$. The measured hole and electron transit times were about 8.73 ${\mu}s$ and 229.17 ${\mu}s$, respectively.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2013.05a
• /
• pp.19-20
• /
• 2013

Thermoelectic properties of the typical thermoelectric host materials, the tellurides and selenides, are known to be noticeably changed by their volume change due to the strain [1]. In the bismuth telluride ($Bi_2Te_3$) crystal, a substitution of rare-earth element by replacing one of the Bi atoms may cause the change of the lattice parameters while remaining the rhombohedral structure of the host material. Using the first-principles approach by the precise full potential linearized augmented plane wave (FLAPW) method [2], we investigated the Ce substitution effect on the thermoelectric transport coefficients for the bismuth telluride, employing Boltzmann's equation in a constant relaxation-time approach fed with the FLAPW wave-functions within the rigid band approximation. Depending on the real process of re-arrangement of atoms in the cell to reach the equilibrium state, $CeBiTe_3$ was found to manifest a metal or a narrow bandgap semiconductor. This feature along with the strong correlation effect originated by the 4f states of Ce affect significantly on the thermoelectric properties. We showed that the position of the strongly localized f-states in energy scale (Fig. 1, f-states are shaded) was found to alter critically the transport properties in this material suggesting an opportunity to improve the thermoelectric efficiency by tuning the external strain which may changing the location of the f-sates.

• Computers and Concrete
• /
• v.11 no.3
• /
• pp.201-222
• /
• 2013

A comprehensive simulation model for the transport process of fully coupled moisture and multi-species in non-saturated concrete structures is proposed. The governing equations of moisture and ion diffusion are formulated based on Fick's law and the Nernst-Planck equation, respectively. The governing equations are modified by explicitly including the coupling terms corresponding to the coupled mechanisms. The ionic interaction-induced electrostatic potential is described by electroneutrality condition. The model takes into account the two-way coupled effect of moisture diffusion and ion transport in concrete. The coupling parameters are evaluated based on the available experimental data and incorporated in the governing equations. Differing from previous researches, the material parameters related to moisture diffusion and ion transport in concrete are considered not to be constant numbers and characterized by the material models that account for the concrete mix design parameters and age of concrete. Then, the material models are included in the numerical analysis and the governing equations are solved by using finite element method. The numerical results obtained from the present model agree very well with available test data. Thus, the model can predict satisfactorily the ingress of deicing salts into non-saturated concrete.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.351-352
• /
• 2007

Polymers submitted to thermo/electrical stress suffer from ageing that can drastically affect their functional behaviour. Understanding the physico/chemical processes at play during ageing and defining transport regimes in which these mechanisms start to be critical is therefore a prime goal to prevent degradation and to develop new formulation or new materials with improved properties. It is thought that a way to define these critical regimes is to investigate under which conditions (in terms of stress parameters) light is generated in the material by electroluminescence (EL). This can happen through impact excitation/ionization involving hot carriers or upon bi-polar charge recombination (a definition that excludes light from partial discharges, which would sign an advanced stage in the degradation process). After a brief review of the EL phenomenology under DC, we introduce a numerical model of charge transport postulating a recombination controlled electroluminescence. The model output is critically evaluated with special emphasize on the comparison between simulated and experimental light emission. Finally, we comment some open questions and perspectives.