• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.366-366
• /
• 2010

Simulation Program (AFORS-HET 2.4.1) was used, include the basic structure of crystalline silicon thin film as above, below Intrinsic a-Si:H films bonded symmetrical structure (Symmetrical structure) were used. Efficiency with variation of the concentration was grown by the a-Si p-type with increasing concentrations of Na, efficiency with increasing a-Si n-type of Nd Concentrations was not changed, was decreased rapidly when concentrations were decreased. Efficiency was increased when c-Si n-type of Nd concentration was increased, otherwise efficiency was decreased when concentration was decreased.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.240-244
• /
• 1998

The analytical method was developed to calculate efficiency of densifying carbon/carbon (C/C) composites using coal tar pitch as a matrix precursor at each cyle. Three factors were defined in analyzing the densification process: impregnation efficiency, retention efficiency, and overall densification efficiency. The relationships developed were applied to the experimental results for three densification cycles of C/C composites with pitches as an impregnant to evaluate the factors which may depend on the impregnant and on the route of carbonization. The impregnation efficiency increased with the repeated process cycles whereas the retention efficiency decreased irrespective of the impregnant and carbonization route. Carbonization route P+A+G, in which pressure carbonizationl (P) and graphitization (G) were done before after atmospheric pressure carboniztion (A) respectively, using impregnant of high carbon yields was the most effective method in densifying C/C composites.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.456-459
• /
• 2003

In this thesis, We observed the characteristic of the diffraction efficiency according to the wave length of the chalcogenide thin films. The used an $Ag(200{\AA})/As_{40}Ge_{10}Se_{15}S_{35}$ thin film. We made grating formation by each wave length 325nm, 442nm, 632.8nm. After measure diffraction efficiency of the time. We expressed the maxium saturation value at fast time as were the short wavelength and stable characteristic. On the other hand we appeard to the by a maxium diffraction efficiency the 1.7% in 325nm, 0.8% in 442nm, 0.27% in 632.8nm. The maximum diffraction efficiency expressed high value as were the long wavelength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.537-538
• /
• 2005

A way of measuring an efficiency of organic light-emitting diodes are studied. The efficiency is obtained from the current-voltage-luminance characteristics of the devices. Basically, number of charge carriers are obtained from the current-voltage characteristics, and the number of photons are obtained from the current of Si-photodetector. The organic light-emitting diodes are assumed as a lambertian light source and a program is made for calculating the efficiency. A device structure of ITO/TPD/$Alq_3$/Al is manufactured using thermal-vapor evaporation. This device is set into a measuring system and measured the efficiency. The efficiencies are measured using the lab-made program and commercially available equipments. The obtained values are similar to each other within 10% uncertainty.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.1
• /
• pp.1-7
• /
• 2014

A field test of a 70 kW heat pump system with flue gas heat recovery was performed by an experiment at the Korea Institute of Energy Research. The flue gas is exhausted from a 320 RT absorption chiller-heater in the heating season. Using this flue gas, source water of the heat pump is heated by a condensed-type heat exchanger in the chimney. The operating characteristics of the heat recovery heat pump system were analyzed. Based on the results of the experiments, operating maps were obtained, and an optimum operating range is suggested, in which the return and heat source water temperature are $51^{\circ}C$ and $31^{\circ}C$, respectively. Additionally, economic analysis of this system was conducted and about 50% energy cost savings can be expected in the heating season.

• Current Photovoltaic Research
• /
• v.7 no.3
• /
• pp.65-70
• /
• 2019

As a demand of higher power photovoltaic modules, shingled, multi-busbar, half-cell, and bifacial techniques are developed. Multi-busbar module has advantage for large amount of light havesting. And, half-cell is high power module for reducing resistive losses and higher shade tolerance. Recently, researches on multi-busbar is focused on reliability according to adhesion and intermetallic compound between Sn-Pb solder and Ag electrode. And half-cell module is researched to comparing with full-sized cell module for structure difference. In this study, we investigated the factors affecting to efficiency and adhesion of multi-wires half-cell module according to wire thickness, solder thickness, and flux. The results of solar simulator and peel test was that peel strength and efficiency of soldered cell is not related. But samples with flux including high solid material showed high efficiency. The results of FE-SEM and EDX line scan on cross-section between wire and Ag electrode for different flux showed thickness of solder joint between wire and Ag electrode is increasing through solid material increasing. Flux including high solid material would affect to solder behavior on Ag electrode. Higher solid material occurred lower growth of IMC layer because solder permeate to sider of wire ribbon than Ag electrode. And it increased fill factor for high efficiency. In soldering process, amount of solid material in flux and solder thickness are the factor related with characteristic of soldered photovoltaic cell.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.362-365
• /
• 1999

The electrochemical properties of flyash obtained from combustion of fuel in fossil power plants and their performance as anode material of secondary battery have been investigated Various flysh pellets molded at various molding pressure have been used as anode lithium secondary battery. The best Performance was achieved when flyash pellet molded at pressure of 400kgf/$\textrm{cm}^2$ is utilized, that is, charge capacity of 300kgf/$\textrm{cm}^2$ and Coulombic efficiency of larger than 95% have been achieved. In addition, this battery exhibited good cycling performance. Considering these results, we predicted that utilization of the flyash as anode material and polyaniline conducting polymer as cathode material in a secondary will show capacity of 300mAh/g and Coulombic efficiency of higher than 95%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.11
• /
• pp.928-933
• /
• 2001

Perdeuterated hexaflouroacetylacetonato-ytterbium [Yb(SOL-D)$_3$] complexes are synthesized by the keto-enol tautomerism reaction of Yb(SOL-H)$_3$ in methanol-d$_4$ in order to reduce the radiationless transition to the ligands for the high power solid state laser material. The luminescence properties of Yb(SOL-D)$_3$ complex are measured in the following anhydrous deuterated organic solvents ; Methanol-d$_4$, THF-d$_{8}$, PO(O$CH_3$)$_3$ and DMSO-d$_{6}$. The Luminescence intensity, lifetime and quantum efficiency in DMSO-d$_{6}$ are superior to those in other deuterated solvents. It is suggested that the anhydrous DMSO-d$_{6}$ might be the most appropriate solvent for the laser material of Yb(SOL-D)$_3$ complex.complex.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.428-429
• /
• 2006

In this thesis, verifies electrical-optical characteristics of phosphorescent materials. basic structure of fabricating devices is glass/ITO/$\alpha$-NPD($300{\AA}$)/CBP:Guest($300{\AA}$)/BCP($80{\AA}$)/$Alq_3(100{\AA})$/Al($1000{\AA}$). In efficiency, fabrication of organic light emitting diodes using $Ir(btp)_2acac$ phosphorescent material is external quantum efficiency 0.268% as doping concentration 3%. At CIE coordinates, phosphorescent material $Ir(btp)_2acac$ following materials moves high purity red color(x=0.6686, y=0.3243). The brightness shows $285cd/cm^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.69-70
• /
• 2006

We studied increasement of efficiency of Organic Light-emitting Diodes depending on thickness variation of LiF, Material of Electron Injection Layer in structure of ITO/Hole Injection Layer (PTFE)/Hole Transportion Later (TPD)/Emitting Layer (Alq3)/Electron Injection Layer (LiF)/Al. TPD and $Alq_3$ is deposited as rate of 1.3~1.5 [${\AA}/s$] in high vacuum ($5{\times}10^{-6}$ [torr]). In result of these studies, we can know maximum efficiency in 0.7 [nm], thickness of LiF. And samples with electron injection material are increased about 5-fold in maximum efficiency in compare with sample without electron injection material.