• Journal of the Korean Wood Science and Technology
• /
• v.18 no.4
• /
• pp.86-101
• /
• 1990

The primary objective of this research was to investigate the strength properties of Comply, a composite panel. fabricated with particle board as core material and veneer or plywood as face and back. 20types of comply composites were manufactured according to the four specific gravity levels(0.5, 0.6, 0.7 or 0.8) of particleboard core and three veneer or two plywood thicknesses for face and back. They were tested and compared with matching particleboard (control) on moisture content. specific gravity, bending properties(MOE, MOR SPL). nail resistance and internal bond strength. The obtained results were summarized as follows: The increasing effect of modulus of elasticity was shown by the increase of face and back veneer or plywood thickness. The modulus of rupture and stress at proportional limit of the comply composites bonded with 3mm thick veneers or 3mm thick plywood face and back were higher than 2mm thick veneer or 2mm thick plywood as face and back. Both of modulus of rupture and stress at proportional limit on bending of Comply were higher than those of control board. Also the modulus of elasticity of Comply showed much higher than that of control board. The nail resistance of Comply, composed of plywood as face and back was higher than that of veneer. The nail resistance of control board was higher than that of Comply at Sp.Gr 0.7 and 0.8 core boards. Internal bond of Comply, composed of 1mm and 2mm thick veneer as face and back was higher than that of 3mm thick veneer. The increasing effect of modulus of elasticity was shown by the increase of shelling ratio in Comply composed of veneer and plywood as face and back. The modulus of rupture was increased by the increment of shellmg ratio in Compiy, composed of plywood as face and back. The modulus of elasticity and modulus of. rupture of comply were higher than those of particleboard(control) in effect of shelling ratio. Therefore it was concluded that the mechanical property values of Comply were clearly greater than those of particleboard(control).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.373-379
• /
• 2010

EMAT has been applied in various fields for flaw detection and material characterization because it has noncontact property in wave generation and a good mode selectivity. Unfortunately, however, EMAT shows low signal to noise ratio relative to commercial contact transducer because of low energy conversion efficiency. If the phase matching through the control of time delay between each coil consisting of the array EMAT is accomplished, it is expected that it will be a solution for the improvement of low signal to noise ratio. In this experiment, the phased array EMATs which consists of 3 or 4 meander coils and one big magnet were fabricated for surface and vertical shear wave generation. Effect of phased delay control on signal directivity and amplitude enhancement was verified. A slit with the depth of 0.5 mm and a side-drill hole of 0.5 mm diameter were clearly detected by fabricated phased array EMATs, respectively.

• Journal of KIISE:Software and Applications
• /
• v.32 no.11
• /
• pp.1147-1155
• /
• 2005

This paper deals with Iris recognition as one of biometric techniques which is applied to identify a person using his/her behavior or congenital characteristics. The Iris of a human eye has a texture that is unique and time invariant for each individual. First, we obtain the feature vector from the 2D Iris pattern having a property of size invariant and using the fuzzy LDA which is further through four types of 2D Gabor wavelet. At the recognition process, we compute the similarity measure based on the correlation values. Here, since we use four different matching values obtained from four different directional Gabor wavelet and select the maximum value, it is possible to minimize the recognition error rate. To show the usefulness of the proposed algorithm, we applied it to a biometric database consisting of 300 Iris Patterns extracted from 50 subjects and finally got more higher than $90\%$ recognition rate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1005-1016
• /
• 2002

In this paper, a 2 GHz tapered shape of multiport power divider/combiner modified from the model published by [10] and adopted PBG(Photonic Band Gap) structure is proposed. Parameters determining electrical property of the circuit structure have been analyzed by HFSS simulation. For input matching, balance of output signals and phase linearity at each output port, one circular hole has been etched out on the circuit surface. 1:2 and 1:3 power dividers/combiners designed by this study have been compared with the same circuits designed by the method of [10] in terms of S-parameters. As a result, it has been found that tile modified structure and PBG of power divider/combiner have improved return loss more than 20 dB and another 18 dB. respectively, at 2 GHz.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.6
• /
• pp.716-721
• /
• 2003

This paper deals with the iris recognition as one of biometric techniques which are applied to identify a person using his/her behavior or congenital characteristics. The iris of a human eye has a texture that is unique and time invariant for each individual. First, we obtain the feature vector from the 2D iris pattern having a property of size invariant and divide it into 24 sectors which are further through three types of 2D Gabor filters. At the recognition process, we compute the similarity measure based on the correlation values. Here, since we use three different matching values obtained from three different directional Gabor filters and select the maximum value among them, it is possible to minimize the recognition error rate. To show the usefulness of the proposed algorithm, we applied it to a biometric database consisting of 50 iris patterns extracted from 10 subjects and finally get more higher than 90% recognition rate.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.2
• /
• pp.257-262
• /
• 2017

In this paper, we proposed a rectangular planar monopole antenna with a double sleeve that applied to a half-cut and a discontinuous feed structure. A rectangular planar monopole antenna with a double sleeve was cut in half along the magnetic symmetry line, and impedance matching was achieved by a discontinuous structure was applied to a feeder and by adjusting the double sleeve gap. We used the HFSS simulator of ANSYS company to confirm the antenna parameter property, and the antenna size was $21{\times}40mm^2$. In the proposed antenna, the simulation frequency range with VSWR of 2 or less was 2.6GHz to 10.25GHz. The bandwidth was 7.65GHz. The frequency range of the fabricated antenna was 3.3GHz to 9.75GHz, and the bandwidth was 6.45GHz. The measured radiation pattern frequencies were 3.5GHz, 5.5GHz, 7.5GHz, and 9.5GHz. A radiation pattern similar to the dipole antenna pattern was obtained at all frequencies.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.93-96
• /
• 2015

The aim of the estimation of disparity map is to find the corresponding pixels from similar two or more images. However, it is a difficult problem to get precise and consistent disparity under a variety of real world situations. In other words, the color values of stereo images are easily influenced by radiometric properties such as illumination direction, illumination color, and camera exposure. Therefore, conventional stereo matching methods can have low performances under radiometric conditions. In this paper, we propose an approaching of disparity map estimation that is reliable in controlling various radiometric variations close to the real environment. This method is motivated by following constancy. Even though each other has different radiometric property in stereo images, intensity of pixels of object have general constancy in specific block. Experimental results show that the proposed method has better performances compared to the comparison group under different radiometric conditions between stereo images. Consequentially, the proposed method is able to estimate the disparity map in stable under various radiometric variations.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2662-2670
• /
• 2009

The effect of the reflector type for the SAW filter on the characteristics of the slanted finger IDT filter have been studied by computer simulation. The IDT was evaporated by Aluminum-Copper alloy. The design condition was optimized by the phase shift of the SAWfilter for WCDMA. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness are $5,000{\AA}$, and the width and the space of reflector are $3.6{\mu}m$ and $2.0{\mu}m$, respectively. Frequency response of the fabricated SFIT filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 8.2MHz. And we could obtain that the return loss is less then 16dB, the ripple characteristics is probably 4dB and the triple transit echo is less then 18dB after when we have matched impedance.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.151-160
• /
• 2002

Cow image processing technique would be useful not only for recognizing an individual but also for establishing the image database and analyzing the shape of cows. A cow (Holstein) has usually the unique speckle pattern. In this study, the individual recognition of cow was carried out using the speckle pattern and the content-based image retrieval technique. Sixty cow images of 16 heads were captured under outdoor illumination, which were complicated images due to shadow, obstacles and walking posture of cow. Sixteen images were selected as the reference image for each cow and 44 query images were used for evaluating the efficiency of individual recognition by matching to each reference image. Run-lengths and positions of runs across speckle area were calculated from 40 horizontal line profiles for ROI (region of interest) in a cow body image after 3 passes of 5$\times$5 median filtering. A similarity measure for recognizing cow individuals was calculated using Euclidean distance of normalized G-frame histogram (GH). normalized speckle run-length (BRL), normalized x and y positions (BRX, BRY) of speckle runs. This study evaluated the efficiency of individual recognition of cow using Recall(Success rate) and AVRR(Average rank of relevant images). Success rate of individual recognition was 100% when GH, BRL, BRX and BRY were used as image query indices. It was concluded that the histogram as global property and the information of speckle runs as local properties were good image features for individual recognition and the developed system of individual recognition was reliable.

• Journal of Broadcast Engineering
• /
• v.10 no.3
• /
• pp.357-371
• /
• 2005

In this Paper, we propose a new motion search algorithm called CDTS (Cross-Diamond-Triangle Search algorithm) that uses optimal search pattern according to the position of a search area to improve the performance of CDS(Cross-Diamond Search algorithm) as well as CDHSs(Cross-Diamond-Hexagonal Searches algorithms). We analyze motion distributions in various test video sequences to apply optimal search pattern according to a position of search area. Based on the result of this analysis, we propose a new triangle-shaped search pattern whose structure is asymmetric while previous search patterns are generally symmetric in conventional algorithms. In CDTS, we apply cross- and diamond-shaped search patterns to central search areas, and triangle- and diamond-shaped patterns to the other areas. Applying CDTS to test video sequences, the proposed scheme can reduce search points more than CDS and CDHSs by 16.22$\%$ and 3.09$\%$, respectively, without any visual quality degradation.