• Journal of Drive and Control
• /
• v.19 no.3
• /
• pp.39-46
• /
• 2022

In South Korea, to evaluate the rollover safety of domestic vehicles, the maximum slope angle of the vehicle is specified, which is verified by the rollover safety test of driving vehicles. However, the domestic rollover safety test is not suitable for buses, because the small amount of static stability factor (SSF) will invalidate the rollover experimental equation due to the high center of mass position of buses. To solve the above problems, a dynamic model of the bus is prepared with assumptions of mass and suspension spring properties. Subsequently, the maximum slope angle of the model was computed by using the simulation of multi-body dynamics, and the result was compared with actual test results to validate the dynamics model. Also, the rollover Fishhook (roll stability) test was conducted in the simulation for driving model. During the simulation, roll angle and roll rate were calculated to check if a rollover occurred. Through the rollover simulation of buses, the domestically regulated formula for rollover safety and the procedure of rollover test for driving vehicles are evaluated. The conclusion is that the present regulation of rollover test should be reconsidered for buses to ensure to get the valid results for rollover safety.

• Geomechanics and Engineering
• /
• v.34 no.4
• /
• pp.381-396
• /
• 2023

The present paper evaluates seismic bearing capacity of rock masses subjected to loads of strip footings using the upper bound method. A general formula was proposed to evaluate the seismic bearing capacity considering both the horizontal and vertical accelerations of the earthquake and the effects of footing embedment depth simultaneously. Modified Hoek-Brown failure criterion was employed for the rock mass. Some comparisons were made with the available solutions and the finite element numerical models to show the accuracy of the developed upper bound formulations. The obtained results show significant improvement compared to the other available solutions. By increasing the horizontal earthquake acceleration from 0.1 to 0.3, the bearing capacity was reduced by up to 39%, while the effect of the vertical earthquake acceleration depends on its direction. An upward acceleration in the range of zero to 0.2 results in an increase in the bearing capacity by up to 24%, while the downward earthquake acceleration has an adverse effect. Also, by increasing the embedment depth of the footing from zero to 5 times the footing width, the value of seismic bearing capacity was raised about 86%. The obtained results were presented as design tables for use in practical applications.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.2
• /
• pp.21-27
• /
• 2003

In general, simple fluid added mass method is used for the seismic and vibration analysis of the immersed structure to consider the fluid-structure interaction effect. Actually, the structural response of the immersed structure can be affected by both the fluid added mass and damping caused by the fluid viscosity. These variables appeared as a consistent matrix form with the coupling terms. In this paper, finite element formula for the inviscid fluid case and viscous fluid case are derived from the linearized Navier Stoke's equations. Using the finite element program developed in this paper, the analyses of fluid added mass and damping for the hexagon core structure of the liquid metal reactor are carried out to investigate the effect of fluid viscosity with variation of the fluid gap and Reynolds number. From the analysis results, it is verified that the viscosity significantly affects the fluid added mass and damping as the fluid gap size decrease. From the analysis results of eccentricity effect on the fluid added mass and damping of the concentric cylinders, the fluid added mass increase as the eccentricity increases, however the fluid damping increases only when the eccentricity is very severe.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.99-106
• /
• 2013

Concrete materials subjected to impact by high velocity projectiles exhibit responses that differ from those when they are under static loading. Projectiles generate localized effects characterized by penetration of front, spalling of rear and perforation as well as more widespread crack propagation. The magnitude of damage depends on a variety of factors such as material properties of the projectile, impact velocity, the mass and geometry as well as the material properties of concrete specimen size and thickness, reinforcement materials type and method of the concrete target. In this study, penetration depth of front, spalling thickness of rear and effect of spalling suppression of concrete by fiber reinforcement was evaluated according to compressive strength of concrete. As a result, it was similar to results of the modified NDRC formula and US ACE formula that the more compressive strength is increased, the penetration depth of front is suppressed. On the other hand, the increase in compressive strength of concrete does not affect spalling of rear suppression. Spalling of rear is controlled by the increase of flexural, tensile strength and deformation capacity.

• Herbal Formula Science
• /
• v.24 no.1
• /
• pp.17-30
• /
• 2016

Objectives Rehmanniae Radix Preparata was prepared in the traditional Rehmanniae Radix Preparata preparation method set forth in the 『Treasured Mirror of Eastern Medicine(Donguibogam)』 with a view to measuring the contents of 5-Hydroxymethyl-2-furaldehyde(5-HMF) at individual stages of steaming and sundrying and identifying new chemical components.Methods Based on the traditional Rehmanniae Radix Preparata preparation method set forth in the 『Treasured Mirror of Eastern Medicine』, Rehmanniae Radix Preparata steamed and sundried once through nine times was prepared. Thereafter, 5-HMF contents were analyzed and new chemical components were identified in the Rehmanniae Radix Preparata using Waters HPLC e2695, 2640 detectors, a Waters Acquity UPLC system, and a Micromass Q-TOF Premier mass spectrometer.Results The Rehmanniae Radix Preparata preparation method set forth in the 『Treasured Mirror of Eastern Medicine』 is a unique preparation method in Republic of Korea different from that in China. In the first stage of the method, fresh Rehmanniae Radix Crudus was divided into high quality, medium quality, and low quality ones named Rehmanniae Radix Crudus (Caelum)(天黃), Rehmanniae Radix Crudus (Homo)(人黃), and Rehmanniae Radix Crudus (Terra)(地黃) respectively to use Rehmanniae Radix Crudus (Caelum) and Rehmanniae Radix Crudus (Homo) for preparation of juice while using Rehmanniae Radix Crudus (Terra) to make Rehmanniae Radix Preparata. In the second stage, Rehmanniae Radix Crudus (Caelum) and Rehmanniae Radix Crudus (Terra) were made into juice and Rehmanniae Radix Crudus (Terra) was soaked in the juice. In the third stage, among auxiliary materials, rice wine named Purum Vinum Oryzae(淸酒) brewed from sticky rice was sprinkled on Rehmanniae Radix Crudus (Terra) to the extent that Rehmanniae Radix Crudus (Terra) became wet. In the fourth stage, Rehmanniae Radix Preparata steamed in earthenware steamer was dried under natural sunlight. The contents of 5-HMF in Rehmanniae Radix Preparata steamed and sundried once through nine times were shown to be below 0.1% in all cases. Pomolic acid was identified as a new chemical component.Conclusions In conclusion, the Rehmanniae Radix Preparata preparation method set forth in the 『Treasured Mirror of Eastern Medicine』 is thought to be a unique preparation method in South Korea in which Rehmanniae Radix Preparata is completed through the first stage in which fresh Rehmanniae Radix Crudus collected from fields is divided into high, medium, and low quality ones and fresh Rehmanniae Radix Crudus juice is made, the second stage in which the high quality fresh Rehmanniae Radix Crudus is soaked in the fresh Rehmanniae Radix Crudus juice, the third stage in which the fresh Rehmanniae Radix Crudus is steamed, and the fourth stage in which the steamed Rehmanniae Radix Crudus is dried.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.538-542
• /
• 2015

The transverse moment of inertia is an indispensable factor in analyzing the roll motion characteristics of ships and the calculating method needs to be based on the more reasonable theories when deciding the value as the results and reliability of analysis could be much affected by the correctness. However, the mass distribution and shape of hulls are quite complicated and give much difficulties in case of calculating the value directly from the ship design data, furthermore even acquiring the detailed design data for calculation is almost impossible. Therefore some simpler ways are practically adopted in the assumption that the gyradius of roll moment can be decided by a given ratio and hull width. It is well known that the responses of the free roll decay are varied according to the value of roll moment in view of roll period and amplitude decay ratio, so that the general formula to get the moment value can be derived also from the observation of roll decay responses. This study presents how the roll period and decay ratio are interrelated each other from the roll motion characteristics with suggesting a general formula to be able to calculate roll moment from it. Finally, the obtained general formula has been applied to a ship data to check the resultant characteristics through analyzing graphs and showed that the roll moment becomes more accurate when rolling period and decay ratio are considered together in calculation.

• Clinical and Experimental Pediatrics
• /
• v.49 no.11
• /
• pp.1125-1139
• /
• 2006

In 1991, the Ministry of Health & Social affairs adopted a nationwide service program for neonatal screening of phenylketonuria, galactosemia, maple syrup urine disease, homocystinuria, histidinemia & congenital hypothyroidism for newborns delivered from low class pregnant women registered in health centers. Government decreased the test items from six to two, PKU & congenital hypothyroidism to increase test numbers with same budget from 1995. Government decided to test PKU & hypothyroidism for all newborns from 1997. 78 laboratories wanted to participate for neonatal screening test in 1999. Government didn't decide laboratory center for a certain district and placed responsibility on free competition. Government are planning to test 573,000 newborns from 1998, Government decided to screen 6 items PKU, congenital hypothyroidism, maple syrup urine disese, homocystinuria, galactosemia and congenital adrenal hyperplasia from 2006. 17 laboratores are participating now. The cost of screening test is supported by both the federal government and local government on a 40-60 basis. In case a patient with an inherited metabolic disease is diagnosed by screening of government program, special milk is provided at government's expense. Interlaboratory quality control was started 6 times a year from 1994. According to the government project, 3,707,773 newborns were screened. 86 PKU, 718 congenital hypothyroidism were detected. So incidence of PKU is 1/43,114 and congenital hypothyroidism is 1/4,612. Maeil dairy company produced new special formula for PKU, MMA and PA, MSUD, urea cycle disorder, homocystinuria, isovaleric acidemia from Oct. 1999. The cost benefit of performing screening procedures coupled with treatment has been estimated to be as high as 1.77 times in PKU, 11.11 times in congenital hypothyroidism than cost without screening. We are trying to increase the budget to test all newborns for Tandem mass sereening & Wilson disease from 2008. Now it is a very important problem to decrease laboratory numbers of neonatal screening in Korea. So we are considering 4-5 central laboratories which cover all newborns and are equipped with tandem mass spectrometer & enzyme immunoassay for TSH, 17OHP & enzyme colorimetric assay for galactose.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.3
• /
• pp.1181-1184
• /
• 2015

Background: Accurate measurement of breast mass size is fundamental for treatment planning. We evaluated performance of BreastLight apparatus in detection breast of masses with this in mind. Materials and Methods: From July 2011 to September 2013, a total of 500 women referred to mammography unit in Yazd, Iran for screening were recruited to this study. Performance of BreastLight in detection breast masses regard their sizeing, measured with clinical breast examination (CBE), mammography and sonography, was assessed. Sonographic and mammography examinations were performed according to breast density among women in two groups of women younger (n=105) and older (n=395) than 30 years. Size correlations were performed using Spearman rho analysis. Differences between mass size as assessed with the different methods (mammography, sonography, and clinical examination) and the BreastLight detection were analyzed using $X^2$-trend test. Results: Performance of the BreastLight in detection of lesions smaller than or equal to 1 cm assessed by CBE, mammography and sonography was 4.4%,7.7% and 12.5% and for masses larger than 4 cm was 65%, 100% and 57.1%, respectively. The performance of BreastLight in detection was significantly increased with larger masses (p<0.001). Conclusions: We conclude that clinical measurement of breast cancer size is as accurate as that from mammography or ultrasound. Accuracy can be improved by the use of a simple formula of both clinical and mammographic measurements.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.108.2-108.2
• /
• 2012

Recent results from microlensing surveys show that a free-floating planet or a wide-separation planet is more numerous than a main-sequence star in the Galaxy. Moreover, the detection efficiency of the planets will be improved in next-generation experiments with a high survey monitoring frequency. However, microlensing events produced by both planets appear similar light curves with a short duration timescale, thus it is difficult to distinguish them. In this paper, we investigated the detectable separation range of a wide-separation planet as the planet bound to its host star. We construct the fractional deviation maps using the magnifications of the planetary lensing and the single-lensing by planet itself for various parameters such as a mass ratio, separation, and source radius. As a result, we found that the pattern of the fractional deviation is related to the ratio of source radius to caustic size, and the ratio satisfying the detection criterion (i.e., ${\geq}5%$ in the fractional deviation) varies with a separation. Hence, we derived a fitting formula as the function of a mass ratio and a source radius to reflect the variation in the calculations of the detectable separation range of a wide-separation planet as the planet bound to its host star. In addition, we estimated the condition that a wide-separation planet can be detected as a single-lensing event under the finite source effect. We found that such a case is possible provided that the source radius is smaller than ~2.5 times of Einstein ring radius of a planet, regardless of a separation or a mass ratio.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.2
• /
• pp.294-306
• /
• 2008

The purpose of this study is a men's dress shirt pattern by somatotype for mass customization system that is rising to the surface as a new production system. Subjects were 65 men aged from 25 to 44 for making research pattern and 9 men for wearing test. The dress shirt went through the secondary wearing test and sensory evaluation to verify the propriety of the research pattern. The results were as follows: For making research dress shirts pattern used the body parts size that were height, the circumference of the neck, the chest circumference, the length between biacromion, the arms length, and the waist circumference. The waist back length, the waist to hip length and the pattern length of were set by the calculation formula based on the height. The ease of 16cm for the chest circumference and A type had the ease of 10cm for the waist circumference, Y type had the ease of 8cm and B type had 12cm. Through the wearing test, the research pattern showed significant difference from the comparative patterns so additional two items of the length between biacromion and waist circumference were added to the items used in the comparative patterns through which satisfactory results were obtained. In the secondary wearing test for the dress shirt, all the items, except for the front centerline, were evaluated excellent. As a result of evaluating by the figure type, the normal type was evaluated best in all the items.