• The Journal of Advanced Prosthodontics
• /
• v.8 no.5
• /
• pp.372-379
• /
• 2016

PURPOSE. Alginate mixers available in the market do not have the automatic proportioning unit. In this study, an automatic proportioning unit for the alginate mixer and controller software were designed and produced for a new automatic proportioning unit. With this device, it was ensured that proportioning operation could arrange weight-based alginate impression materials. MATERIALS AND METHODS. The variation of coefficient in the tested groups was compared with the manual proportioning. Compression tension and tear tests were conducted to determine the mechanical properties of alginate impression materials. The experimental data were statistically analyzed using one way ANOVA and Tukey test at the 0.05 level of significance. RESULTS. No statistically significant differences in modulus of elastisity (P>0.3), tensional/compresional strength (P>0.3), resilience (P>0.2), strain in failure (P>0.4), and tear energy (P>0.7) of alginate impression materials were seen. However, a decrease in the standard deviation of tested groups was observed when the customized machine was used. To verify the efficiency of the system, powder and powder/water mixing were weighed and significant decrease was observed. CONCLUSION. It was possible to obtain more mechanically stable alginate impression materials by using the custom-made proportioning unit.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.18-21
• /
• 2003

Fused Deposition Modeling (FDM) parts are made by piling up thin layers that cause the stair stepping effect at the surface of FDM parts. This effect brings about poor surface roughness of the part and requires additional post machining such as manual finishing that is detrimental to the part geometry and time consuming. Determining optimal build orientation for FDM parts can be one solution to minimize the post machining. However, by using the CAD model, calculating the optimal build orientation is impractical due to heavy computing process. In order to calculate the optimal build orientation with high speed. the surface roughness model based on measured data and interpolation is newly developed in this research. Also. the genetic algorithm (GA) is applied for acquiring reliable solution. Finally, It is verified from the test that the presented approach is very efficient for reducing the additional post machining process fer FDM parts.

• The Korean Journal of Food And Nutrition
• /
• v.29 no.4
• /
• pp.573-582
• /
• 2016

The objective of the current study was to compare the execution of hygiene and safety management according to the characteristics of children's food service stations, with the ultimate objective of providing sanitary and safe food service to children. To this end, the study conducted surveys of 73 public and private pre-schools with fewer than 100 children in district A from July 30 to October 31 2015. The differences were evaluated by t-test and analysis of variance. The confidence and validity of the results were analyzed by six food ingredient and facilities management questions, three personal hygiene and facilities management questions, four environmental management questions, and five storage and treatment management questions; for a total of 18 questions. The cumulative distribution of the four factors was 61.569%, and the Cronbach's alpha was 0.821, which indicated that the results were reliable. The results revealed that public pre-schools (a) and home-based pre-schools (b) had different levels of food ingredient and facility management, but no differences in the number of cooks, number of children served, type of food distribution, and the existence of mass food service facilities. The results of the study may be used to develop hygiene and safety management manual and educational contents to promote the health of the children served.

• Toxicological Research
• /
• v.20 no.1
• /
• pp.55-61
• /
• 2004

Respiratory effects in full time welders include bronchitis, airway irritation, lung function changes, and lung fibrosis. Welder's pneumoconiosis has been generally determined to be benign and not associated with respiratory symptoms based on the absence of pulmonary function abnormalities in welders with marked radiographic abnormalities. Accordingly, to investigate pulmonary function changes during 60 days induced by welding-fume exposure, male Sprague-Dawley rats were exposed to manual metal arc-stainless steel (MMA-SS) welding fumes with concentrations of 64.8$\pm$0.9 mg/$m^3$ (low dose) and 107.8 $\pm$ 2.6 mg/$m^3$ (high dose) total suspended particulates for 2 hr/day, 5 days/week in an inhalation chamber for 60 days. Pulmonary function was measured every week with whole body plethysmograph compensated (WBP Comp, SFT38116, Buxco Electronics, Sharon, CT). The rats exposed to the high dose of welding fumes exhibited statistically significant (p<0.05~0.01) body weight decrease as compared to the control whereas cell number increase of the bronchoalveolar lavage fluid (BALF) (total cell, macrophage, polymorphonuclear cell and lymphocyte) during the 60 days exposure period. And only tidal volume was significantly decreased in dosedependantly during 60 days of MMA-SS welding fume exposure. This pulmonary function change with inflammatory cell recruitment confirms the lung injury caused by the MMA-SS welding fume exposure.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.1
• /
• pp.11-18
• /
• 2020

The emergence of the flow-through cell (FTC) method has made up for the limitations of previous dissolution test methods, but the high cost of the FTC dissolution devices have seriously hindered the progression of research and application of the FTC. This new design uses a peristaltic pump to simulate the sinusoidal flow rate of a piston pump. The flow profile of each peristaltic pump was sinusoidal with a pulsation of 120 ± 1 pulses per minute, and the flow rate ranged from 1.0 - 36.0 mL/min. The flow control of each channel was adjusted independently so the flow errors of the seven channels were close to 2%. The structure of the system was simplified, and the cost was reduced through manual sampling and immersing the FTC in a water bath. The dissolution rate of the theophylline and aminophylline films was determined, and good experimental results were obtained.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.171-176
• /
• 2005

This paper presents a novel Intelligent-Welding-Carriage (IWC) for automation of curved block in shipbuilding. The curved block is usually used in both front and back side of the ship. In curved block root gap is big, 1-7 (mm) and inclination, 0-30 (deg). Since available conventional carriage type is limited to use below root gap of 3 (mm), only manual welding is employed in curved block. To adopt an IWC in curved block, it requires control of the welding conditions, i.e., voltage. current, weaving speed, dwell time and travel speed, with respect to root gap and inclination to achieve good welding qualify. In this paper, an IWC is developed for automization of welding operation to accommodate gap and inclination. Kinematics model and dynamics using Lagrangian formulation of the manipulator is introduced. IWC utilizes a database to perform accurate welding. The database is programmed based on numerous experimental test results with respect to gap, inclination, material, travel speed, weaving condition, voltage, and current. Finally, experimental result using PID control is addressed for verifying the trajectory tracking accuracy of end-effector.

• Journal of Korean Society of Transportation
• /
• v.26 no.4
• /
• pp.161-172
• /
• 2008

The level of service (LOS) evaluation method of the Highway Capacity Manual (HCM) is limited to intersections with pre-timed signal operation, while advanced real-time traffic control systems have been expending in the field. This paper proposes a preliminary framework for LOS analysis at isolated intersections controlled by COSMOS, the real-time traffic control systems robustly utilizing the degree of saturation as basic inputs. The proposed LOS evaluation framework was devised with a pilot model developed to estimate the average cycle length and green times of COSMOS. The validation test showed that the proposed framework was able to accurately project the LOS, which was separately evaluated based upon field data.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.61-68
• /
• 2004

Recently, there has been an increasing demand for computer-vision based inspection and/or measurement system as a part of factory automation equipment. Existing manual inspection method can inspect only specific samples and has low measuring accuracy as well as it increases working time. Thus, in order to improve the objectivity and reproducibility, computer-aided analysis method is needed. In this paper, front and side profile inspection and/or data transfer system are developed using computer-vision during the inspection process on three kinds of pipes coming from a forming line. Straight line and circle are extracted from profiles obtained from vision using Laplace operator. To reduce inspection time, Hough Transform is used with clustering method for straight line detection and the center points and diameters of inner and outer circle are found to determine eccentricity and whether good or bad. Also, an inspection system has been built that each pipe's data and images of good/bad test are stored as files and transferred to the server so that the center can manage them.

• Journal of Sasang Constitutional Medicine
• /
• v.31 no.3
• /
• pp.66-78
• /
• 2019

Objectives We report 1 treatment case with Onbaek-won which is based on Sasang constitutional medicine for specific symptoms that leukoaraiosis Soeumin patient has. Methods We treated leukoaraiosis Soeumin patient suffering from specific symptoms. We prescribed Onbaek-won for her physical symptoms. The improvement of her symptoms were evaluated by Manual Muscle Test(MMT) and Visual Analogue Scale(VAS). Results After the Onbaek-won was given, the patient's most of symptoms were improved. And there was not any adverse effect. Conclusions This study shows that using Onbaek-won can be effective treatment for leukoaraiosis Soeumin patient's specific symptoms.

• Korean Journal of Agricultural Science
• /
• v.49 no.3
• /
• pp.679-690
• /
• 2022

As the supply and demand of pork has become a significant concern in Korea, controlling it has become a critical challenge for the industry. However, compared to the demand for pork, which has relatively stable consumption, it is not easy to maintain a stable supply. As the preparation of measures for a supply-demand crisis response and supply control in the pig industry has emerged as an important task, it has become necessary to establish a stable supply model and create an appropriate manual. In this study, a pork supply prediction model is constructed using reported data from the pig traceability system. Based on the derived results, a method for determining the supply-demand crisis stage using a statistical approach was proposed. From the results of the analysis, working days, African swine fever, heat wave, and Covid-19 were shown to affect the number of pigs graded in the market. A test of the performance of the model showed that both in-sample error rate and out-sample error rate were between 0.3 - 7.6%, indicating a high level of predictive power. Applying the forecast, the distribution of the confidence interval of the predicted value was established, and the supply crisis stage was identified, evaluating supply-demand conditions.