• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.537-540
• /
• 2010

본 논문에서는 보의 주철근을 대상으로 건물정보모델링(BIM, Building Information Modeling)통합 설계 시스템 상에서 배근 설계 및 철근 형상화 알고리즘을 구축하여 자동배근 시스템(ARPM, Automatic Reinforcement Placing Module)을 개발하는데 목적이 있다. 구조분야에서의 BIM 프로세스는 정보호환체계를 구축하는 과정에 있으며, 철골 구조 프로세스의 경우 표준 호환 포맷을 이용하여 원활한 정보 호환 체계를 유지하고 있다. 하지만, 철근 콘크리트의 BIM 통합 설계 시스템은 철근 배근정보의 생성과 호환이 원활하지 않아 표준 정보 호환 체계가 구축되지 않은 실정이다. 기존 2차원 기반 프로세스에서는 철근 배근 설계에 있어 표준화된 기준에 따른 배근이 아닌 관행이나 일률적인 배근 지침에 따라 배근 상세를 정하고 있고, 2차원 배근 설계 결과만 제시하고 있어 상호 호환 가능한 철근 배근 정보데이터가 생성되지 않는다. 철근 콘크리트 구조에서의 철근 배근 정보를 생성하고 BIM 통합 구조 설계시스템에서의 정보 호환성을 확보하기 위해, 보의 주철근을 대상으로 구조 해석 데이터베이스와 통합 설계 플랫폼 간의 호환 시스템을 생성하고, 콘크리트학회 콘크리트 구조설계기준에 따른 배근 설계 및 철근 형상화 알고리즘을 구축하여 자동배근시스템(ARPM)을 개발하는데 목적이 있다.

• Structural Engineering and Mechanics
• /
• v.23 no.5
• /
• pp.469-486
• /
• 2006

The main objective of this study was to investigate the seismic behavior of damaged reinforced concrete frames rehabilitated by introducing cast in place reinforced concrete infills. Four bare and five infilled frames were constructed and tested. Each specimen consisted of two (twin) 1/3-scale, one-bay and two-story reinforced concrete frames. Test specimens were tested under reversed-cyclic lateral loading until considerable damage occurred. RC infills were then introduced to the damaged specimens. One bare specimen was infilled without being subjected to any damage. All infilled frames were then tested under reversed-cyclic lateral loading until failure. While some of the test frames were detailed properly according to the current Turkish seismic code, others were built with the common deficiencies observed in existing residential buildings. The variables investigated were the effects of the damage level and deficiencies in the bare frame on the seismic behavior of the infilled frame. The deficiencies in the frame were; low concrete strength, inadequate confinement at member ends, 90 degree hooks in column and beam ties and inadequate length of lapped splices in column longitudinal bars made above the floor levels. Test results revealed that both the lateral strength and lateral stiffness increased significantly with the introduction of reinforced concrete infills even when the frame had the deficiencies mentioned above. The deficiency which affected the behavior of infilled frames most adversely was the presence of lap splices in column longitudinal reinforcement.

• Structural Engineering and Mechanics
• /
• v.54 no.6
• /
• pp.1097-1109
• /
• 2015

A novel optimization approach for reinforced concrete (RC) biaxially loaded columns is proposed. Since there are several design constraints and influences, a new computation methodology using iterative analyses for several stages is proposed. In the proposed methodology random iterations are combined with music inspired metaheuristic algorithm called harmony search by modifying the classical rules of the employed algorithm for the problem. Differently from previous approaches, a detailed and practical optimum reinforcement design is done in addition to optimization of dimensions. The main objective of the optimization is the total material cost and the optimization is important for RC members since steel and concrete are very different materials in cost and properties. The methodology was applied for 12 cases of flexural moment combinations. Also, the optimum results are found by using 3 different axial forces for all cases. According to the results, the proposed method is effective to find a detailed optimum result with different number of bars and various sizes which can be only found by 2000 trial of an engineer. Thus, the cost economy is provided by using optimum bars with different sizes.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.201-204
• /
• 2006

The shear resistance of RC beams is subject to the amount of shear-reinforcing bars ($p_w$) and yield strength ($f_{wy}$) as well as their interactive influence ($p_wf_{wy}$). Thus, it is reasonably expected that high-strength steel bars can greatly reduce the necessary amount of shear-reinforcing bars. On the other hand, although the bond strength is influenced by the amount of shear reinforcing bars, it is not affected by the yield strength. Thus, there is often an issue that bond failure occurs before shear failure depending on the arrangement of shear reinforcing bars. It is a common practice to set sub-ties for the transverse confinement of the main re-bars as a method to prevent the bond failure. However, it can also become a factor in decreased work efficiency due to the complexity of the construction. This study experimented with simultaneous use of high-strength transverse reinforcing bars ($f_{wy}=800MPa$) and U-shaped transverse reinforcing bars of regular strength ($f_{wy}=300MPa$) in an attempt to decrease the necessary quantity of shear reinforcing bars. The effect of this attempt was investigated through fundamental experimental research in terms of the improvement in shear resistance and bond strength as well as the ease of construction.

• Earthquakes and Structures
• /
• v.5 no.3
• /
• pp.297-319
• /
• 2013

Two destructive earthquakes occurred on October 23 and November 9, 2011 in Van province of Turkey. The damage in residential units shows significant deviation from the expectation of decreasing damage with increasing distance to epicenter. The most damaged settlement Ercis has the same distance to the epicenter with Muradiye, where no damage occurred while relatively less damage observed in Van having half distance. These three cities seem to have resembling soil conditions. If the damages are evaluated: joint failures and insufficient lap splice lengths are observed to be the main causes of the total collapses in RC buildings. Additionally, low concrete strength, reinforcement detailing mistakes, soft story, heavy overhang, pounding and short columns are among other damage reasons. Examples of damages due to non-structural elements are also given. Remarkable points about seismic damages are: collapsed buildings with shear-walls, heavily damaged buildings despite adequate concrete strength due to detailing mistakes, undamaged two-story adobe buildings close to totally collapsed RC ones and undamaged structural system in buildings with heavily damaged non-structural elements. On the contrary of the common belief that buildings with shear-walls are immune to total collapse among civil engineers, collapse of Gedikbulak primary school is a noteworthy example.

• Journal of the Korean Institute of Rural Architecture
• /
• v.7 no.3
• /
• pp.109-118
• /
• 2005

This study is to find out the plan intention of the central space through visual analysis on the east and west stone pagodas relative to a main Buddhist hall, and the relation between the stone pagodas in Hwaeomsa.(華嚴寺) According to the analysis of it in this study, we make conclusions as follows; 1) The east and west stone pagodas was arranged with overlapping each Daeungjeon(大雄殿) and Gakhwangjeon(覺皇殿) for the view of a specific viewpoint, on the right of Bojeru(普濟樓). 2) The centering around a compositive axis which connect Gakhwangjeon, stone lantern, and stairs, the axis of two stone pagodas is not coincident. 3) Courtyard in Hwaeomsa is separated by high a stone wall for reinforcement, but it is integrated into visual perception owing to height of two stone pagodas connected visual line to Daeungjeon and Gakhwangjeon.

• Journal of the Korean Institute of Rural Architecture
• /
• v.12 no.1
• /
• pp.49-56
• /
• 2010

This paper is aimed to clarify field technique of non-educated constructors in timber structure of korean-style secondary station(Gong-So) on the annex of catholic church. The main object of this study is Sin-Sung and Su-Bun secondary stations which post-lintel structure was 2high columns(Go-Ju) 5beams(Ryang) in Jeon-Buk area of Korea. We reached the following conclusion. Firstly, these secondary stations are required a lots of space for number of persons with the introduction of basilica plane. These plans have different intervals in the layout. Secondly, they constructed the holy space by using high columns(Nae-Jin-Go-Ju). The former problems of plan layout are sloved by reinforcement and replacement eaves and rafter of logitudinal. Thirdly, the elements showed the natural feature such as irregular wooden floor, arch-type head pentrating tie and a ceiling. In the end, we knew that non-educated constructor had found a way in the problem for accepting unreasonable work.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.3
• /
• pp.163-171
• /
• 2001

Lateral confinement pressure generate improvements in strength and ductility of confined concrete. Carbon fiber sheets have a lot of merits, such as light weight, high strength and ease for construction, when it is applied to the defected structural member for the strengthening of shear and flexure. The purpose of this experimental study is to evaluate the strength characteristics of the reinforced concrete column confined with carbon fiber sheets. The main variables in this test are concrete strength ($290kgf/cm^2$ called N type, $505kgf/cm^2$ called H type) and pre-loading. In the test, a total of twelve specimens, which were all $10{\times}10cm$ in size, 117 cm in length, have a 2.85 reinforcement ratio, have been used. The results indicate that the strength was enhanced 26%~30% in N type, 11%~16% in H type specimens which was confined with carbon fiber sheets.

• Textile Coloration and Finishing
• /
• v.16 no.5
• /
• pp.42-47
• /
• 2004

The main objective of this work is to develop melt-blown nonwoven fabric composite materials have electromagnetic shielding characteristics using thin copper film. Melt-blown nonwoven fabric is the matrix phase and thin copper films are the reinforcement of the composite materials. Thin copper films are incorporated as conductive fillers to provide the electromagnetic shielding property of the melt-blown nonwoven fabric. The width and interval of thin copper films in the nonwoven fabric are varied by changing 1, 3, 5 mm for thin copper film's width and 1, 3, 5 mm for thin copper film's interval. The shielding effectiveness(SE) of various melt-blown nonwoven fabrics is measured in the frequency range of 50 MHz to 1.8 GHz. The variations of SE of melt-blown nonwoven fabric with width and interval of thin copper films are described. Suitability of melt-blown nonwoven fabric for electromagnetic shielding applications is discussed. The results indicate that the melt-blown nonwoven fabric composite material using thin copper film can be used for the purpose of electromagnetic shielding.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.5
• /
• pp.161-168
• /
• 2010

Practicing engineers and researchers need computational tools that estimate accurately the cyclic response of RC walls, and in particular, force and deformation capacities and their materials strains. So this paper describes a nonlinear truss modeling approach for reinforced concrete walls, or in general, for plane stress reinforced concrete elements subjected to cyclic reversals. Nonlinear vertical, horizontal, and diagonal truss elements are used to represent concrete and steel reinforcement. The wall having aspect ratio of 1.2 was chosen to be compared with the experimental results. Here, four types of main diagonal member models and three types of diagonal members models were applied to find out more accurate results of analysis.