• 한국연소학회지
• /
• 제1권1호
• /
• pp.11-18
• /
• 1996

The stabilization characteristics of diffusion flame formed behind a bluff body with fuel injection slits was experimentally investigated by varying main fuel injection angles and auxiliary fuel injection conditions. The flame stability limits, temperature and length of recirculation zone, direct and schlieren photographs of flames were measured in order to study the stabilization mechanism of the diffusion flame. The results of this investigation are as follows. The stability limits can be improved by the condition of the kind and quanity of the injected auxiliary fuel. The length and temperature decrease with injection of auxiliary fuel, and these phenomena are remarkable when LPG is injected into the recirculation zone. When the LPG is injected into the recirculation zone, flame remains sooty. Fluctuation of fuel and main stream is generated actively by air injection.

• 한국분무공학회지
• /
• 제5권3호
• /
• pp.17-26
• /
• 2000

The main parameter commonly used to evaluate spray distribution is spray angle. Spray angle is important because it influences the axial and radial distribution of the fuel. Spray angles were measured and compared for the two non-air assisted injectors such as 2hole-2stream 4hole-1stream injectors used for port fuel injection gasoline engines with n-heptane as a fuel by three different measuring techniques, i.e., digital image processing, shadowgraphy, and spray patternator, respectively. Fuel was injected with the injection pressures of 0.2-0.35 MPa into the room temperature and atmospheric pressure environment. In digital image processing approach, the selection of the transmittance level is critical to obtain the edge of spray and hence to measure the spray angle. From the measurement results by the shadowgraphy technique, it is dear that the spray angle is varied during the spray injection period. The measurement results from spray patternator show that the different spray angles exist in different region. Spray angle increases with the increase in the injection pressure. it is suggested that the spray angle and stream separated angle should be specified when spray is characterized for 2hole-2stream injector, because spray angle is much different though stream separated angle is same. It was also considerably affected by the measurement techniques introduced in this experimental work. However, the optimal axial distance for measuring the spray angle seems to be at least 60-80 mm from the injector tip for two non-air assisted injectors.

• 청정기술
• /
• 제13권4호
• /
• pp.300-307
• /
• 2007

본 연구에서는 연료분출각의 변화에 따라 보염기(cylindrical stabilizer) 후류에 형성되는 확산화염의 화염 안정성, 재순환영역의 길이 및 온도, 보염기 후류의 난류강도 분포, 재순환영역의 연소가스 농도 등을 측정하고, 화염의 직접사진 및 슐리렌사진을 촬영하여 확산화염의 연소특성을 고찰하였다. 화염안정성은 연료분출각과 주류공기 유속의 영향을 받으며, 재순환영역의 길이와 온도는 연료분출각의 영향을 받았다. 재순환영역의 길이가 짧고 온도가 낮을수록 화염안정성이 양호하지만, 연료분출각의 변화에 따른 난류강도 분포에는 별로 차이가 없었다. 재순환영역 내 미연가스 농도가 높고 이산화탄소 농도가 낮은 경우, 화염안정성은 양호하지만 연소상태는 불량한 것으로 나타났다. 연소효율, 고부하 출력, 대기환경, 연료의 청정연소조건 등을 고려하여 적절한 연료분출각을 선정함으로써 양호한 연소조건을 유지할 수 있다.

• 한국분무공학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• 동력기계공학회지
• /
• 제18권5호
• /
• pp.156-163
• /
• 2014

Diesel engine is most suitable one for biodiesel fuel because the compression-ignition diesel engine has desirable fuel consumption due to higher thermal efficiency and in addition, the improvement of the fuel consumption also leads to a reduction of $CO_2$ emission and then it does not need to have spark-ignition system, which means that there is less charge on the technic and complexity. In this study, the spray behavior characteristics of the vegetable palm oil were analyzed by using a common-rail injection system of commercial diesel engine and the results were compared with those obtained for the diesel fuel. The injection pressures and blend ratios of palm oil and diesel(BD3, BD5, BD20, BD30, BD50, and BD100) were the main parameters. The experiments were conducted for different injection pressures: 500bar, 1000bar, 1500bar, and 1600bar by setting injection duration to $500{\mu}s$. Consequently, it was found that there is no significant difference in the macro characteristics of the spray behavior(spray penetration and spray angle) in response to change in the blend ratio of palm oil and diesel at a fixed injection pressure. In particular, all experiments showed the spray angle about $12^{\circ}{\sim}13^{\circ}$.

• 한국분무공학회지
• /
• 제21권2호
• /
• pp.95-103
• /
• 2016

The effect of pilot injection quantity on the combustion and emissions characteristics of a compression ignition engine with a biodiesel-compressed natural gas (CNG) dual fuel combustion (DFC) system is studied in this work. Biodiesel is used as a pilot injection fuel to ignite the main fuel, CNG of DFC. The pilot injection quantity is controlled to investigate the characteristics of combustion and exhaust emissions in a single cylinder diesel engine. The injection pressure and injection timing of pilot fuel are maintained at approximately 120 MPa and BTDC 17 crank angle, respectively. Results show that the indicated mean effective pressure (IMEP) of biodiesel-CNG DFC mode is similar to that of diesel-CNG DFC mode at all load conditions. Combustion stability of biodiesel-CNG DFC mode decreased with increase of engine load, but no notable trend of cycle-to-cycle variations with increase of pilot injection quantity is discovered. The combustion of biodiesel-CNG begins at a retarded crank angle compared to that of diesel-CNG at low load, but it is advanced at high loads. Smoke and NOx of biodiesel-CNG are simultaneously increased with the increase of pilot fuel quantity. Compared to the diesel-CNG DFC, however, smoke and NOx emissions are slightly reduced over all operating conditions. Biodiesel-CNG DFC yields higher $CO_2$ emissions compared to diesel-CNG DFC over all engine conditions. CO and HC emissions for biodiesel-CNG DFC is decreased with the increase of pilot injection quantity.

• 한국분무공학회지
• /
• 제6권3호
• /
• pp.23-31
• /
• 2001

An experimental study was carried out to understand the spray characteristics of three kinds(kerosene, heating oil & diesel) of hydrocarbon-fuels. Fuel temperature and injection pressure were main variables in the experiment. Fuel Temperature was changed to obtain various levels of fuel viscosity. Spray angle and spray length were measured by using LVS(Laser Vapor Screen) photographs. 1D PDPA system was used to measure droplet size & droplet velocity. In room temperature, spray characteristics of three kinds of fuels were good, especially in case the fuel injection pressure was more than $6Kgf/cm^2$ It was also found that spray characteristics were poor in case fuel kinematic viscosity was more than 5cSt.

• 한국분무공학회지
• /
• 제12권3호
• /
• pp.154-159
• /
• 2007

Spray tip penetration and spray angle for one main injection were measured at the atmospheric condition with the fuel injection pressure of 270 bar and 540 bar. It investigates an effect of different nozzle hole geometry of conventional cylindrical one and those of elliptical ones. Injection period represented by injector pulse drive was fixed at 1ms. From the result of this study, it is shown that spray tip penetration becomes shorter and spray angle becomes wider with the elliptical nozzle hole geometry due to fast break-up of a fuel liquid column.

• 한국항공우주학회지
• /
• 제33권1호
• /
• pp.78-84
• /
• 2005

환형 노즐을 갖는 불화중수소 화학레이저 시스템에서 레이저빔 발진은 불소 원자와 중수소 분자의 혼합을 통해서 얻어진다. 초음속 연소기에서 연료의 분사각이 성능에 큰 영향을 미친다는 연구에 근거하여, 혼합률을 증진시키기 위한 연구로서 주유동과 일정각을 가지고 분사되는 중수소의 불소 원자와의 혼합률 증진에 대한 수치적 연구를 수행하였다. 중요 결과로서 중수소 분사각(10, 20, 40도)이 커짐에 따라서 최대 소신호 광학이득계수와 레이저 공동내의 압력이 상승하게 된다. 또한, 광학이득계수와 공동압력의 관점에서 불화중수소 화학레이저 발진을 위한 최대 성능은 20~40도 사이의 중수소 분사각에서 나타난다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.64-71
• /
• 2005

효과적인 초음속 연소를 위해 연료와 공기의 빠른 혼합이 필요하며, 혼합 향상을 위해 연료분사 방식에 대한 여러 연구들이 수행되어 왔다. 본 연구에서는 길이-깊이 비가 4.8, 후면 경사각이 $22.5^{\circ}$인 개방형 공동 모델을 사용하였으며, 마하수 1.92에서 운동량비에 따른 분사구 주변의 유동 특성 및 연소실 내 압력 분포를 슐리렌 가시화와 압력 측정을 사용하여 파악하였다. 운동량비는 연료의 침투거리와 분사지역의 유동에 큰 영향을 끼친다.