• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.212-218
• /
• 2013

A transfer method of neutron radiography was developed to measure the size of the end plug and a gap of an intact K102L-2, the irradiated fuel of a ballooned K174L-3, a ballooned and ruptured K98L-3. A typical irradiation time of 25 min. was determined to obtain a film density of between 2 and 3 of SR X-ray film with neutrons of $1.5{\times}10^{11}n{\cdot}cm^{-2}$. To validate and calibrate the results, a RISO fuel standard sample, Cd plate and ASTM-BPI/SI were used. An activated latent image formed in the $100{\mu}m$ Dy foil was subsequently transferred in a dark room for more than 8 hours to the SR film which is a maximum of three half-lives. Due to the L/D ratio an unsharpness of $9.82-14{\mu}m$ and a magnification of 1.0003 were given. After digitizing an image of SR film, the ballooning gap of the plug was discernible by an H/V filter of image processing. The gap size of the ballooned element, K174L-3, is equal to or greater than 1.2 mm. The development of a transfer method played a pivotal role in developing high burn-up of Wolsung and PWR nuclear fuel type.

• Parasites, Hosts and Diseases
• /
• v.53 no.1
• /
• pp.113-117
• /
• 2015

Cryptosporidium spp., ubiquitous enteric parasitic protozoa of vertebrates, recently emerged as an important cause of economic loss and zoonosis. The present study aimed to determine the distribution and species of Cryptosporidium in post-weaned and adult pigs in Shaanxi province, northwestern China. A total of 1,337 fresh fecal samples of post-weaned and adult pigs were collected by sterile disposable gloves from 8 areas of Shaanxi province. The samples were examined by Sheather's sugar flotation technique and microscopy at${\times}400$ magnification for Cryptosporidium infection, and the species in positive samples was further identified by PCR amplification of the small subunit (SSU) rRNA gene. A total of 44 fecal samples were successfully amplified by the nested PCR of the partial SSU rRNA, with overall prevalence of 3.3%. The average prevalence of Cryptosporidium infection in each pig farms ranged from 0 to 14.4%. Species identification by sequencing of SSU rRNA gene revealed that 42 (3.1%) samples were Cryptosporidium suis and 2 (0.15%) were Cryptosporidium scrofarum. C. suis had the highest prevalence (7.5%) in growers and the lowest in breeding pigs (0.97%). C. suis was the predominant species in pre-weaned and adult pigs, while C. scrofarum infected pigs older than 3 months only. A season-related difference of C. suis was observed in this study, with the highest prevalence in autumn (5.5%) and the lowest (1.7%) in winter. The present study provided basic information for control of Cryptosporidium infection in pigs and assessment of zoonotic transmission of pigs in Shaanxi province, China.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.1
• /
• pp.69-76
• /
• 1986

The measuring Method by stylus, which measures surface roughness, has been widely used since G. Schmaltz developed the first equipment of that type. Withe the resent development of the measuring method by stylus, surface foughness testing instruments of the very high magnification ratio, hundreds of thousands, are manu- factured. However, as the techniques of the high precision roughness measurement are being required, the response problems due to the tip shapes and the plastic deformations of measured surface of mild material are to be serious factors. In this study, diamond stylus of tip radius $0.5\mu\textrm{m}$, $2\mu\textrm{m}$, $5\mu\textrm{m}$ and $10\mu\textrm{m}$ were used under the measuring force of 0.01gf, 0.02gf, 0.07gf, 0.4gf and 1.6gf, and from the experimental data, maximum measured value devrements between $2\mu\textrm{mR}$ stylus and $5\mu\textrm{mR}$ stylus, $2\mu\textrm{mR}$ stylus and $10\mu\textrm{mR}$ stylus are 22% and 31%, respectively when the measured value of $2\mu\textrm{mR}$ stylus goes to $0.01\mu\textrm{m Ra}$, $\lambda$ c2.5mm. And it is shown that plastic deformations on the plastic deformations on the measured surface are proportional to W/R(W;measured force, R;stylus tip radius).

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.243-254
• /
• 1999

This paper presents a numerical study for developing the moment magnifier method that is applicable to RC flat plates subject to combined axial compressive and floor load. For the nonlinear finite element analysis, a computer program addressing material and geometric nonlinearities was developed. The flat plates to be studied are designed in accordance with the Direct Design Method in Korean Building Code for Structural Concrete. This paper proposes the buckling force and the moment magnification factor for the flat plate under the governing load condition that is the combined vertical and subsequently applied uniaxial compressive load. The buckling force is defined with two ingredients: the buckling coefficient and the effective flexural rigidity. Parametric studies are performed to investigate variations of the buckling coefficient and the effective flexural rigidity. Based on the numerical results, this paper provides the design values of the buckling coefficient and the effective flexural rigidity, and the design procedure for the moment magnifier method.

• Archives of Craniofacial Surgery
• /
• v.13 no.2
• /
• pp.139-142
• /
• 2012

Purpose: To reconstruct the midface, local flaps such as nasolabial flaps have been frequently used. These local flaps, however, have the shortcomings of requiring a secondary operation or limitations in the movement of the flap. Thus, new methods have been developed. This paper reports a case wherein the basal cell carcinoma on the cheek was resected and the skin and soft tissue defect was successfully treated using a facial artery perforator flap. Methods: A 68-year-old female consulted the authors on the basal cell carcinoma that developed on her cheek. The mass was fully resected and revealed a $2.3{\times}2.3cm$ defective region. Using a Doppler ultrasonography, the facial artery path was traced, and using a loupe magnification, the facial artery perforator flap was elevated and the defective region was covered with the flap. Results: The flap developed early venous congestion, but it disappeared without any treatment. Six months after the surgery, the patient was satisfied with the postoperative result. Conclusion: The facial artery perforator flap has a thin pedicle. It offers a big arc of the rotation that allows free movement and one-stage operation. These strengths make the method useful for the reconstruction of the midface among other procedures.

• The Journal of the Korean dental association
• /
• v.52 no.10
• /
• pp.623-632
• /
• 2014

The facial asymmetries include maxillary, mandibular, and chin asymmetries, although the most common deformity is primarily in the mandible. Common causes of this type of asymmetry can include asymmetric growth of the condyle or the mandible. In these patients, the location of the Me would be deviated to the shorter side because of the asymmetric growth of the mandible, and, commonly, the maxillary occlusal plane would be tilted toward the deviated side because the maxilla likely grows asymmetrically according to the pattern of asymmetric mandibular growth. Three-dimensional CT images are ideal for evaluating the size and location of anatomic structures, and such reconstructed images allow the use of software that can show anatomic structures from numerous angles, allowing actual measurements of distances and angles without problems of magnification, distortion, or superimposition caused by 2-dimensional imaging. In the present study using 3D-CT imaging, the 8 parameters, including measurements of the upper midline deviation, maxillary canting in the canine and first molar regions, width of the upper arch, width of the mandible at the Go, vertical length of the ramus, inclination of the ramus, and deviation of the Me were easily measured. The dentition should be orthodontically decompensated and dental midline should ensure incisor midlines positioned in the midline of each jaw before surgical correction. Surgical correction could be considered such as canting or yawing correction in the frontal or horizontal aspect, respectively.

• Journal of Technologic Dentistry
• /
• v.39 no.4
• /
• pp.235-242
• /
• 2017

Purpose: The aim of this study was to evaluate the marginal and internal gap of zirconia copings fabricated by CAD/CAM system and to research the effect of cement space on the fit of zirconia prosthesis. Methods: Zirconia copings were designed using 3shape software and then milled from presintered zirconia blocks by Kavo dental milling machine. The cement space was set at $0{\mu}m$ around the margins for all groups, and additional cement space appling 1 mm above the finish lines of tooth. The samples were classified into 4 groups according to the cement space setting(Cs-0, Cs-40, Cs-80, Cs-120). Replica technique used to investigate marginal and internal gap. The silicone film thickness was recorded using a optical microscope with image software analysis system at 75${\times}$magnification. The assessment performed on the six points in bucco-lingual and mesio-distal sections(4 groups, 10 copings per group, 12 measuring points per coping). The data were statistically analyzed with one-way ANOVA followed by pair-wise Tukey's post hoc tests(${\alpha}$<0.05). Results: Better marginal and internal fit values were exhibited by $80{\mu}m$ cement space. The results showed that different cement space values had statistically significant effect on the marginal and internal gap of zirconia copings(p<0.001). The gap of margin and axial wall area was smaller than that the gap of occlusal area in all groups(p<0.001). Conclusion : Effect of different cement spaces on the marginal and internal gap of zirconia copings.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.11
• /
• pp.979-983
• /
• 2013

The three-dimensional measurement method of confocal systems is a spot scanning method which has a high resolution and good illumination efficiency. However, conventional confocal systems had a weak point in that it has to perform XY axis scanning to achieve FOV (Field of View) vision through spot scanning. There are some methods to improve this problem involving the use of a galvano mirror [1], pin-hole array, etc. Therefore, in this paper we propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array in a dual microscope configuration. We made an area scan possible by using a combination MLA (Micro Lens Array) and pin-hole array, and used an objective lens to improve the light transmittance and signal-to-noise ratio. Additionally, we made it possible to change the objective lens so that it is possible to select a lens considering the reflection characteristic of the measuring object and proper magnification. We did an experiment using 5X, 2.3X objective lens, and did a calibration of height using a VLSI calibration target.

• Korea Journal of Hospital Management
• /
• v.12 no.2
• /
• pp.43-68
• /
• 2007

The administration of a regional public hospitals are expending from profit preference to publicity preference. The weight rate for a profitability and publicity of performance assessment has changed from 84:16 which was resulted by the assessment executed firstly in 1989 to 39:61 as resulted in 2004, the final assessment execution in 2005. Regional public hospitals are exerting and promoting a magnification in public sector to raise up the public-score. With comparison between publicity scores and profitability scores in original scores basis excluding weight rate, the publicity scores ranked higher than profitability scores although the latter was higher by 2002. However, for the administration performance of the regional public hospitals, the deficits increased 11 times from \92.6billion deficits with \460.3billion cost increased by 457% although income as \367.7billion increased by 394% comparing the last 2004 year to the first 1989 year for profit & loss statement of a regional public hospitals. There was analysis for the relation in yearly basis partitioning publicity and profitability for the assessment scores of the to regional public hospitals confirm the accumulated deficits of the hospitals like this attribute to the extension of public sector. The result showed that there was distinct plus relationship from 1999 although a minus relationship in general until 1997 except 1992 and there is a more plus relationship as approaching 2004. That is, it is hard to tell that the accumulated deficits increase of regional government medical center attributed to extension of public sector. On the contrary, the analysis showed the extension of public sector has a mutual relationship with uplift of profitability Meanwhile, it showed that operation cost rate and labor cost are the factors which influence a revenue & expenditure rate among the profitability index according to the results of relation analysis for the representative index of profitability and that of publicity.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.4
• /
• pp.294-302
• /
• 2015

PURPOSE. The purpose of this study was to verify the clinical-feasibility of additive manufacturing by comparing the accuracy of four different manufacturing methods for metal coping: the conventional lost wax technique (CLWT); subtractive methods with wax blank milling (WBM); and two additive methods, multi jet modeling (MJM), and micro-stereolithography (Micro-SLA). MATERIALS AND METHODS. Thirty study models were created using an acrylic model with the maxillary upper right canine, first premolar, and first molar teeth. Based on the scan files from a non-contact blue light scanner (Identica; Medit Co. Ltd., Seoul, Korea), thirty cores were produced using the WBM, MJM, and Micro-SLA methods, respectively, and another thirty frameworks were produced using the CLWT method. To measure the marginal and internal gap, the silicone replica method was adopted, and the silicone images obtained were evaluated using a digital microscope (KH-7700; Hirox, Tokyo, Japan) at 140X magnification. Analyses were performed using two-way analysis of variance (ANOVA) and Tukey post hoc test (${\alpha}=.05$). RESULTS. The mean marginal gaps and internal gaps showed significant differences according to tooth type (P<.001 and P<.001, respectively) and manufacturing method (P<.037 and P<.001, respectively). Micro-SLA did not show any significant difference from CLWT regarding mean marginal gap compared to the WBM and MJM methods. CONCLUSION. The mean values of gaps resulting from the four different manufacturing methods were within a clinically allowable range, and, thus, the clinical use of additive manufacturing methods is acceptable as an alternative to the traditional lost wax-technique and subtractive manufacturing.