• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.404-411
• /
• 2012

The reliability of solid oxide fuel cells (SOFCs) particularly depends on the high quality of solid oxide electrolytes. The application of thinner electrolytes and multi electrolyte layers requires a more reliable characterization method. Most of the investigations on thin film solid electrolytes have been made for the parallel transport along the interface, which is not however directly related to the fuel cell performance of those electrolytes. In this work an array of ion-blocking metallic Ti/Au microelectrodes with about a $160{\mu}m$ diameter was applied on top of an ultrathin ($1{\mu}m$) yttria-stabilized-zirconia/gadolinium-doped-ceria (YSZ/GDC) heterolayer solid electrolyte in a micro-SOFC prepared by PLD as well as an 8-${\mu}m$ thick YSZ layer by screen printing, to study the transport characteristics in the perpendicular direction relevant for fuel cell operation. While the capacitance variation in the electrode area supported the working principle of the measurement technique, other local variations could be related to the quality of the electrolyte layers and deposited electrode points. While the small electrode size and low temperature measurements increaseed the electrolyte resistances enough for the reliable estimation, the impedance spectra appeared to consist of only a large electrode polarization. Modulus representation distinguished two high frequency responses with resistance magnitude differing by orders of magnitude, which can be ascribed to the gadolinium-doped ceria buffer electrolyte layer with a 200 nm thickness and yttria-stabilized zirconia layer of about $1{\mu}m$. The major impedance response was attributed to the resistance due to electron hole conduction in GDC due to the ion-blocking top electrodes with activation energy of 0.7 eV. The respective conductivity values were obtained by model analysis using empirical Havriliak-Negami elements and by temperature adjustments with respect to the conductivity of the YSZ layers.

• Journal of Korean Dental Science
• /
• v.7 no.2
• /
• pp.49-57
• /
• 2014

Purpose: To evaluate the effect of different surface treatment methods (yttria-tetragonal zirconia polycrystal [Y-TZP] primers, air-abrasion, and tribochemical surface treatment) on the shear bond strength between (Y-TZP) ceramics and etch-and-rinse non-10-methacryloyloxydecyl dihydrogen phosphate (MDP)-containing resin cements. Materials and Methods: Y-TZP ceramic surfaces were ground flat with 600-grit silicone carbide abrasives paper and then divided into seven groups of ten. They were treated as the following: untreated (control), Monobond Plus (IvoclarVivadent), Z-PRIME Plus (Bisco Inc.), ESPE Sil with CoJet (3M ESPE), air-abrasion, Monobond Plus with air-abrasion, and Z-PRIME Plus with air-abrasion. The surface of Y-TZP specimens was analyzed under a scanning electron microscope (SEM). Non-MDP-containing cements were placed on the surface-treated Y-TZP specimens. After thermocycling, shear bond strength test was performed. Bond strength values were statistically analyzed using one-way analysis of variance and Student-Newman-Keuls multiple comparison test (P<0.05). Result: The Z-PRIME Plus treatment in combination with air-abrasion produced the highest bond strength ($14.94{\pm}1.70MPa$) followed by Monobond Plus combined with air-abrasion ($10.70{\pm}1.71MPa$), air-abrasion ($10.47{\pm}1.60MPa$), ESPE Sil after CoJet treatment ($10.38{\pm}0.87MPa$), Z-PRIME Plus application ($10.00{\pm}1.70MPa$), and then Monobond Plus application ($9.25{\pm}0.86MPa$). The control ($6.70{\pm}1.49MPa$) indicated the lowest results (P<0.05). The SEM results showed different surface morphologies according to surface treatment methods compared with the Y-TZP control. Conclusion: The shear bond strength between the Y-TZP ceramic and the non-MDP-containing resin cement was the greatest when the surface was treated with air-abrasion and MDP-containing Z-PRIME Plus primer.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.234-239
• /
• 1999

A Abstract Yttria-stabilized zirconia(YSZ) thin films were synthesized by plasma enhanced chemical vapor deposition process. $Zr[TMHD]_4$ $Y[TMHD]_3$ precursors and oxygen were used with the deposition temperature of $425^{\circ}C$ and rf power ranging 0-100 watt. Effects of the deposition parameters were studied by X-ray diffraction and thickness anal­ysis. YSZ thin films have cubic crystal structure with (200) orientation. From the results of EDX analysis, the converte ed content of TEX>$Y_2O_3$ was determined to be 0-36%, and the film thickness was increased with bubbling temperature which is considered to be due to increasing TEX>$Y_2O_3$ flux. The depth profiles of Zr, Y and 0 appeared relatively $\infty$nstant through film thickness. Columnar grains of $1000~2000\AA$ grew vertical to the substrate surface for the case of Ar carri­er gas. In case of He carrier gas, the grain size was observed to be about $1000~2000\AA$. X-ray diffraction data showed the increase of lattice constant with TEX>$Y_2O_3$ content. It was that the presence of the cracks formed during film deposition, partially released the stress generated by the increase of lattice constant.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.6
• /
• pp.258-263
• /
• 2013

4 mol% Yttria-stabilized zirconia (4YSZ) coatings are fabricated by Air Plasma Spray (APS) and Electron Beam Physical Vapor Deposition (EB-PVD) with top coating of thermal barrier coating (TBC). NiCrAlY based bond coat is prepared as 150 ${\mu}m$ thickness by conventional APS (Air Plasma Spray) method on the NiCrCoAl alloy substrate before deposition of top coating. Each 4YSZ top coating shows different tribological behaviors based on the inherent layer structures. 4YSZ by APS which has splat-stacked structure shows lower friction coefficient but higher wear rate than 4YSZ by EB-PVD which has columnar structure. For 4YSZ by APS, such results are expected due to the sliding wear accompanied with local delamination of splats.

• Journal of Korean Dental Science
• /
• v.11 no.1
• /
• pp.14-20
• /
• 2018

Purpose: The purpose of this study is to measure and compare the removal torques of different cements applied in attachments of zirconia restorations on titanium (Ti) abutments fitted with retrievable cement-type slot (RCS) on the lingual side for the better retrievablity by use of a slot driver. Materials and Methods: Three types of cements were used in the experiment: two permanent cements in $RelyX^{TM}$ U200 (RU) (3M ESPE) which is a resin cement and $FujiCem^{TM}$ (FC) (GC) which is a resin-modified glass ionomer cement, and a temporary cement in $Freegenol^{TM}$ temporary cement (TC) (GC). Measurements of removal torques were conducted as follows; an attached sample was fixed on the equipment customized for the experiment; a slot driver was connected to a MGT12 (Mark-10 Corp.), a torque measurement instrument; the sample had the driver fitted to its RCS and then was rotated until the it was removed; and finally, the maximum torque value was recorded. Result: As for the removal torque measurement results, the average values were $47.9{\pm}2.6Ncm$ for RU, $43.4{\pm}1.5Ncm$ for FC, and $20.9{\pm}1.0Ncm$ for TC. The statistical analysis using Kruskal-Wallis test yielded the significance probability of P<0.05 (P=0.002), which confirmed the presence of significant differences between the three groups. Conclusion: All three cements exhibit clinically acceptable levels of removal torque when applied to an upper zirconia implant restoration fitted with a lingual slot, with RU and FC, the two permanent cements, having the significantly higher values than that of TC, the temporary cement.

• Journal of the Korean Ceramic Society
• /
• v.54 no.4
• /
• pp.285-291
• /
• 2017

This study investigated the effects of grain size and phase constitution on the mechanical properties of $3Y-ZrO_2$ by varying the sintering conditions. The raw powder prepared by a low-cost wet milling using the coarse solid oxide powders was sintered by both pressureless sintering and hot-pressing, respectively. As increasing holding time at $1450^{\circ}C$ for pressureless sintering, it promoted the microstructural coarsening of matrix grains and the phase transformation to tetragonal phase, whereas the bimodal microstructure embedded with abnormal $cubic-ZrO_2$ grains was observed regardless of sintering time. On the other hand, the specimens hot-pressed at $1300^{\circ}C$ for 2 h reached ~ 97% of relative density with homogeneous fine microstructure and mixed phase constitution. It was found that the proportion of untransformed monoclinic zirconia had the most adverse effect on the biaxial strength compared to the impacts of grain size and density. The pressureless sintering of the low-cost powder for prolonged sintering time to 8 h led to a decent combination of mechanical properties ($H_V=13.2GPa$, $K_{IC}=8.16MPa{\cdot}m^{1/2}$, ${\sigma}=981MPa$).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.8
• /
• pp.510-515
• /
• 2016

Single-chamber solid oxide fuel cells (SC-SOFCs) consist of only one gas chamber, in which both the anode and the cathode are exposed to the same fuel-oxidant mixture. Thus, this configuration shows good thermal and mechanical resistance and allows rapid start-up and -down. In this study, the unit cell consisting of $La_{0.8}Sr_{0.2}MnO_3$ (cathode) / $Zr_{0.84}Y_{0.16}O_{2-x}$ (electrolyte) / $Ni-Zr_{0.84}Y_{0.16}O_{2-x}$ (anode) was fabricated and its electrochemical property was investigated as a function of temperature and the volume ratio of fuel and oxidant for SC-SOFCs. Impedance spectra were also investigated in order to figure out the electrical characteristics of the cell. As a result, the cell performance was governed by the polarization resistances of the electrodes. The cell exhibited an acceptable cell-performance of $86mW/cm^2$ at $800^{\circ}C$ and stable performance for 3 hs under 0.7 V.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.150-150
• /
• 1999

재료의 광학적 특성을 변화시키기 위한 표면 코팅의 사용을 잘 알려져 있다. 그리고 이러한 광학 코팅은 우리가 주위에서 볼 수 있는 렌즈에서부터 레이저반사경 다 나아가 다양한 광학 필터에 이르기까지 빛의 간섭을 이용한 광학 박막의 코팅은 폭넓게 이용되고 있다. 그러한 응용가운데 불필요한 표면 반사를 방지함으로써 전체 투과율을 강화시키기 위한 무반사(Anti-Reflection) 코팅은 오늘날 광대역 무반사 특성 등 다양한 광학적 요구에 따라 하나 또는 그 이상의 층을 형성함으로써 극적으로 성취할 수 있다. 본 실험은 기존 많이 활용되는 증발법 그리고 스퍼터링 방법과는 달리 고진공하에서 증착 변수를 효과적으로 제어, 박막을 형성할 수 있는 자체 제작된 단일 IBS(Ion Beam Sputtering) 시스템을 이용하여 우수한 광학적 특성을 갖는 광학 재료로써 무반사용 다층박막 형성하기 앞서 MgF2, ZrO2 (yttria stabilized zirconia) 단층 박막을 제조하였으며, 각 증착 변수에 따른 결정학적 및 광학적 특성을 관찰하였다. 본 실험에 사용된 제조 장비로 Kaufman type 2.5inch의 이온 건이 장착된 Ion Beam sputtering 시스템으로 초기 진공도는 5$\times$10-6orr이며, 이온 빔의 전류 밀도는 Fareday cup을 이용했다. 6inch 크기의 ZrO2(yttria stabilized zirconia), MgF2 타겟트를 이용하여 Si(100), glass 기판위에 박막을 성장시켰다. 각 타겟트에 대한 증착변수로 이온 에너지, 기판온도, Ar 가스량을 변화시키면서 박막을 제조하였다. 제조된 박막의 광학적 특성으로 가시 영역에서 투과율의 변화는 자외/가시광선 분광 분석기 (UV/VIS specrophotometer)를 이용하여 측정했다. 그리고 박막의 조성 및 결정학적 구조는 AES EDS와 XRD로 확인하였다. 이온 빔 전압 500V, 빔 저류 55mA일 때 온도는 상온에서 30$0^{\circ}C$까지 승온 후 MgF2 박막의 XRD분석결과 우세한 결정성을 관찰할 수 없었으며, 이 때의 광 투과도는 가시영역에서 80~90%의 값으로 측정되었다. 추후 증착된 막의 결정성을 위해 열처리를 실시하고, 각 증착조건에 대한 결과는 학회 발표시 보고한다.

• Journal of Powder Materials
• /
• v.29 no.6
• /
• pp.468-476
• /
• 2022

Yttria-stabilized zirconia (YSZ) has a low thermal conductivity, high thermal expansion coefficient, and excellent mechanical properties; thus, it is used as a thermal barrier coating material for gas turbines. However, during long-time exposure of YSZ to temperatures of 1200℃ or higher, a phase transformation accompanied by a volume change occurs, causing the YSZ coating layer to peel off. To solve this problem, YSZ has been doped with trivalent and tetravalent oxides to obtain coating materials with low thermal conductivity and suppressed phase transformation of zirconia. In this study, YSZ is doped with trivalent oxides, Nd₂O₃, Yb₂O₃, Al₂O₃, and tetravalent oxide, TiO₂, and the thermal conductivity of the obtained materials is analyzed according to the composition; furthermore, the relative density change, microstructure change, and m-phase formation behavior are analyzed during long-time heat treatment at high temperatures.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.216-221
• /
• 1998

A study on induction plasma deposition with ceramic materials, yttria-stabilized-zirconia ZrO$_2$-Y$_2$O$_3$ (m.p 264O $^{\circ}C$), was conducted with a view developing a new method for nuclear fuel fabrication Before making dense pellets more than 96％TD., the spraying condition was optimized through the process parameters, such as chamber pressure, plasma plate power powder spraying distance, sheath gas composition, probe position, particle size and powders different morphology. The results with a 5mm thick deposit on rectangular planar graphite substrates showed a 97.11％ theoretical density when the sheath gas flow rate was Ar/H$_2$120/20 l/min, probe position 8cm, particle size -75 ${\mu}{\textrm}{m}$ and spraying distance 22cm by AMDRY146 powder. The degree of influence of the main effects on density were powder morphology. particle size, sheath gas composition, plate power and spraying distance, in that order. Among the two parameter interactions, the sheath gas composition and chamber pressure affects density greatly. By using the multi-pellets mold wheel type, the pellet density did not exceed 94%T.D., owing to the spraying angle.