• 구강회복응용과학지
• /
• 제25권1호
• /
• pp.1-12
• /
• 2009

이 논문의 목적은 시멘트 층 내의 응력분포에 대해 금관의 물성과 시멘트의 물성 및 교합력의 방향이 미치는 영향을 이차원 유한요소분석으로 조사하는 것이다. Chamfer 변연을 가지는 23개의 하악 제1대구치 모델을 상정하였다. 금관의 재질은 제 3형 금합금, Ni-Cr 합금, 세라믹, 복합레진 등 4가지이며, 시멘트의 재질은 인산 아연 시멘트와 글라스 아이오노머 시멘트 등 2가지이다. 치축과 평행하게 또는 경사지게 하여 1N 단위로 금관에 하중을 가했다. 시멘트층의 응력은 금관 변연이 다른 곳보다 더 높았다. 치축에 평행한 하중이 치축에 경사진 하중보다 더 높은 응력을 발생시켰다. 경도가 더 큰 금관은 시멘트 층 내에서 더 높은 응력을 나타냈으며, 더 높은 응력은 더 큰 Young's modulus을 나타냈다.

• Restorative Dentistry and Endodontics
• /
• 제43권2호
• /
• pp.19.1-19.10
• /
• 2018

Objectives: This study investigated the effect of continuous application of 10-methacryloyloxydecyldihydrogen phosphate (MDP)-containing primer and luting resin cement on bond strength to tribochemical silica-coated yttria-stabilized tetragonal zirconia polycrystal (Y-TZP). Materials and Methods: Forty bovine teeth and Y-TZP specimens were prepared. The dentin specimens were embedded in molds, with one side of the dentin exposed for cementation with the zirconia specimen. The Y-TZP specimen was prepared in the form of a cylinder with a diameter of 3 mm and a height of 10 mm. The bonding surface of the Y-TZP specimen was sandblasted with silica-coated aluminium oxide particles. The forty tribochemical silica-coated Y-TZP specimens were cemented to the bovine dentin (4 groups; n = 10) with either an MDP-free primer or an MDP-containing primer and either an MDP-free resin cement or an MDP-containing resin cement. After a shear bond strength (SBS) test, the data were analyzed using 1-way analysis of variance and the Tukey test (${\alpha}=0.05$). Results: The group with MDP-free primer and resin cement showed significantly lower SBS values than the MDP-containing groups (p < 0.05). Among the MDP-containing groups, the group with MDP-containing primer and resin cement showed significantly higher SBS values than the other groups (p < 0.05). Conclusions: The combination of MDP-containing primer and luting cement following tribochemical silica coating to Y-TZP was the best choice among the alternatives tested in this study.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.487-501
• /
• 1998

In the case of CAD/CAM ceramic inlay restorations, if isthmus width is widened too much, it may cause fracture of remaining tooth structure or loss of bonding at the luting interface because of excessive displacement of buccal or lingual cusps under occlusal loads. So to clarify the criterior of widening isthmus width, this study was designed to test the tensile bond strength and bond failure mode between dentin and ceramic cemented with luting composite resin cements. Cylindrical ceramic blocks(Vita Cerec Mark II, d=4mm) were bonded to buccal dentin of 40 freshly extracted third molars with 4 luting composite resin cements(group1 : Scotchbond Resin Cement/Scotchbond Multi-Purpose, group2 : Duolink Resin Cement/ All-Bond 2, group3: Bistite Resin Cement/Ceramics Primer, and group4:Superbond C&B). Tensile bond test was done under universal testing machine using bonding and measuring alignment blocks(${\phi}ilo$ & Urn, 1992). After immersion of fractured samples into 1 % methylene blue for 24 hours, failure mode was analysed under stereomicroscope and SEM. Results: The tensile bond strength of goup 1, 2 & 4 was $13.97{\pm}2.90$ MPa, $16.49{\pm}3.90$ MPa and $16.l7{\pm}4.32$ MPa, respectively. There was no statistical differences(p>0.05). But, group 3 showed significantly lower bond stregnth($5.98{\pm}1.l7$ MPa, p<0.05). In almost all samples, adhesive fractures between dentin and resin cements were observed. But, in group 1, 2 & 4, as bond strength increased, cohesive fracture within resin cement was observed simultaneously. And, in group 3, as bond strength decreased, cohesive fracture between hybrid layer and composite resin cement was also observed. Cohesive fracture within dentin and porcelain adhesive fracture were not observed. In conclusion, although adhesive cements were used in CAD/CAM -fabricated ceramic inlay restorations, the conservative priciples of cavity preparation must be obligated.

• 대한치과보철학회지
• /
• 제41권4호
• /
• pp.466-475
• /
• 2003

Statement of problem : In cemented implant-supported porstheses, it is still controversy what kind of cement to use. However, the effect of thermocycling on retentive strength of cemented implant-supported prostheses has not been well investigated. Purpose : This study was tested to evaluate the effects of various cements and thermocycling on retentive strengths of cemented implant-supported prostheses. Material and methods : Prefabricated implant abutments, height 5mm, diameter 6mm, 3-degree taper per side, with light chamfer margins were used. Ten specimens of two-unit fred partial denture were fabricated. The luting agents used for this study were three provisional luting agents which were Temp bond, Temp bond NE, IRM and four permanent luting agents which were Panavia F, Fuji-cem, Hy-bond Zinc cement, Hy-bond Polycarboxylate cement. 24 hours after cementation. the retentive strengths were measured by the universal testing machine with a cross-head speed of 0.5mm/min. Then cementation procedures were repeated and specimens were thermocycled 1000 times at temperature of $5^{\circ}C$ and $55^{\circ}C$. After thermocycling, the retentive strengths were measured. Results : Before thermocycling, the retentive strengths were decreased with the sequence of Panavia F. Fuji-cem. Hy-bond Zinc cement. Hy-bond Polycarboxylate cement, IRM, Temp bond NE and Temp bond, and there were significant differences among each groups(p<0.05). After thermocycling, the retentive strengths were decreased with the sequence of Panavia F. Fuji-cem, Hybond Zinc cement, Hy-bond Polycarboxylate cement, IRM, Temp bond NE and Temp bond, and there were no significant differences among Panavia F, Fuji-cem and Temp bond NE, Temp bond(p>0.05). The retentive strengths before and after thermocycling showed significant differences in Hy-bond Zinc cement. IRM, Temp bond NE and Temp bond(p<0.05). Conclusion : Within the limitation of this study, thermocycling do not affect the retentive strengths of permanent luting agents but the retentive strengths of temporary cements were reduced significantly after thermocyling.

• 대한치과보철학회지
• /
• 제38권5호
• /
• pp.618-630
• /
• 2000

As Fiber-reinforced composite restorations cannot be made without leaving a marginal gap, luting cements play a pivotal role in sealing the margins as a prevention against margnal leakage. A recently introduced adhesive resin cement system is claimed to adhere chemically, as well as mechanically, to tooth substances, dental alloys and porcelain. But when considering the clinical variation conventional cementation using Zinc Phosphate and Glass-Ionomer can be requested. A vitro study was undertaken to compare microleakage and marginal fitness of Fiber-reinforced composite crowns(Targis/Vectris) depending upon luting cements. Fifty non-carious human premolar teeth were randomly divided into five experimental groups of 10 teeth each and luted with five luting cements. ($Bistite\;II^(R),\;Super-bond^(R),\;Variolink\;II^(R)$), Zinc phosphate and Glass-Ionomer cement) After 24 hours of being luted, all specimens were thermocycled 300 times through water bath of $5^{\circ}C\;and\;55^{\circ}C$ in each bath, then the quality of the marginal fitness was measured by the Digital Microscope and marginal leakage was characterized using Dye Penetration technique and the Digital Microscope The results were as follows : 1. The mean values of marginal fit were Bistite II($46.78{\mu}m$), Variolink II($56.25{\mu}m$), Super-Bond($56.78{\mu}m$), Glass-Ionomer($99.21{\mu}m$), Zinc Phosphate($109.49{\mu}m$) indicated a statistically significant difference at p<0.001. 2. The mean microleakage values of tooth-cement interface, restoration-cement interface were increased in the order of Variolink II, Bistite II, Super-Bond, Glass-Ionomer, Zinc Phosphate 3. Crowns luted with resin cement (Bistite II, Super-Bond, Variolink II, etc) exhibited less marginal gap and marginal leakage than those luted with conventional Glass-Ionomer and Zinc Phosphate cement. 4. The results indicated that all five luting systems yielded comparable and acceptable marginal fit.

• 구강회복응용과학지
• /
• 제27권3호
• /
• pp.253-265
• /
• 2011

근관치료된 치아의 수복에서 fiber post 크기와 포스트 공간의 직경이 일치하지 않은 경우, 포스트 공간은 두꺼운 레진 시멘트로 채워지게 된다. 레진 시멘트가 두꺼워지면 시멘트 내에 기포가 형성되어 포스트 분리가 발생되기 쉽다. 이런 문제점을 해결하기 위한 방법은 composite resin을 이용하여 fiber post를 relining하는 것이다. 이렇게 형성된 해부학적 포스트는 포스트 공간에 잘 적합하고 시멘트의 두께를 감소시킨다. 이 연구의 목적은 relining 과정과 임상 과정의 간소화를 위해 사용되고 있는 luting agents 종류에 따른 fiber post의 push-out 결합 강도를 평가하는 것이다. 42개의 발치된 치아는 6개의 그룹(n=7)으로 나누어졌다. (A1: relined fiber post를 Luxacore/all-bond 2로 합착, A2: non-relined fiber post를 Luxacore/all-bond 2로 합착. B1: relined fiber post를 Calibra/XP-bond로 합착. B2: non-relined fiber post를 Calibra/XP-bond로 합착. C1: relined fiber post를 RelyX Unicem으로 합착. C2: non-relined fiber post를 RelyX Unicem으로 합착.) Push-out 결합 강도는 relining procedure와 cement type의 상호작용에 의해 영향을 받는 것으로 나타났다. relined fiber post 그룹이 non-relined fiber post 그룹보다 더 높은 결합 강도를 가지며 fiber post relining 과정은 결합강도에 유의한 영향을 가진다.(p<0.05) Luting agent에 따라 모든 그룹에서 RelyX Unicem의 결합강도가 Luxacore/All-bond 2와 Calibra/XP bond에 의한 것보다 유의하게 더 높았다(p<0.05).

• Imaging Science in Dentistry
• /
• 제48권2호
• /
• pp.97-101
• /
• 2018

Purpose: This study evaluated the radiopacity of contemporary luting cements using conventional and digital radiography. Materials and Methods: Disc specimens (N=24, n=6 per group, ø$7mm{\times}1mm$) were prepared using 4 resin-based luting cements (Duolink, Multilink N, Panavia F 2.0, and U-cem). The specimens were radiographed using films, a complementary metal oxide semiconductor (CMOS) sensor, and a photostimulable phosphor plate (PSP) with a 10-step aluminum step wedge (1 mm incremental steps) and a 1-mm-thick tooth cut. The settings were 70 kVp, 4 mA, and 30 cm, with an exposure time of 0.2 s for the films and 0.1 s for the CMOS sensor and PSP. The films were scanned using a scanner. The radiopacity of the luting cements and tooth was measured using a densitometer for the film and NIH ImageJ software for the images obtained from the CMOS sensor, PSP, and scanned films. The data were analyzed using the Kruskal-Wallis and Mann-Whitney U tests. Results: Multilink (3.44-4.33) showed the highest radiopacity, followed by U-cem (1.81-2.88), Panavia F 2.0 (1.51-2.69), and Duolink (1.48-2.59). The $R^2$ values of the optical density of the aluminum step wedge were 0.9923 for the films, 0.9989 for the PSP, 0.9986 for the scanned films, and 0.9266 for the CMOS sensor in the linear regression models. Conclusion: The radiopacities of the luting materials were greater than those of aluminum or dentin at the same thickness. PSP is recommended as a detector for radiopacity measurements because of its accuracy and convenience.

• 치위생과학회지
• /
• 제18권4호
• /
• pp.218-226
• /
• 2018

불소 적용 후 교정용 브라켓 접착제 종류에 따른 불소의 재흡수성과 표면의 변화를 비교 평가하고자 하였다. 불소가 방출되지 않은 복합레진 Transbond $XT^{(R)}$, 불소 방출성 복합레진 $Blugloo^{(R)}$와 $LightBond^{(R)}$, 레진강화형 글라스 아이오노머 Rely $X^{TM}$ Luting $2^{(R)}$, 재래형 글라스 아이오노머 Fuji $I^{(R)}$를 사용하였다. 시편에서 방출되는 불소 방출량을 측정하였고, 불소 재흡수 능력을 비교하기 위해서 시편에 3가지의 불소 제품(APF gel, Tooth Mousse $Plus^{(R)}$, Fluor Protector)을 도포하였으며, 불소함유 치약으로 잇솔질을 하여 불소방출량 변화를 측정하였고, 표면조도 측정기와 FE-SEM을 이용하여 시편의 표면 조도 및 변화를 비교 평가하였다. Rely $X^{TM}$ Luting $2^{(R)}$와 Fuji $I^{(R)}$에서는 다른 불소 제품인 Tooth Mousse $Plus^{(R)}$, Fluor Protector뿐만 아니라 불소함유 치약으로 잇솔질한 후에도 불소의 재흡수량을 관찰할 수 있었다. Tooth Mousse $Plus^{(R)}$를 도포한 후에는 Transbond $XT^{(R)}$를 제외하고 표면 조도 값이 유의하게 증가하였으며, 모든 교정용 접착제에서 부분적인 미세 필러 입자의 탈락을 보였다. Fluor Protector를 도포한 후에는 Transbond $XT^{(R)}$, Rely $X^{TM}$ Luting $2^{(R)}$를 제외하고 표면 조도 값이 유의하게 증가하였으며, 모든 교정용 접착제의 표면에 막을 형성하여 기포가 생긴 부분을 제외하고 매끄러운 양상을 나타내었다. 모든 교정용 접착제에 APF gel을 도포했을 때는 표면 조도 값이 유의하게 크게 증가하였다. 이상의 결과를 종합해 볼 때, 교정용 브라켓을 접착할 때 치아우식 예방 효과를 도모하기 위한 불소 방출량을 고려한다면 Rely $X^{TM}$ Luting $2^{(R)}$와 Fuji $I^{(R)}$가적극 추천되며, 불소 제품으로는 Tooth Mousse $Plus^{(R)}$, Fluor Protector가 APF gel보다 우수한 것으로 나타났고, 불소가 함유된 치약으로 잇솔질을 하였을 때도 치아우식을 예방할 수 있을 것으로 생각된다.

• 대한치과보철학회:학술대회논문집
• /
• 대한치과보철학회 2002년도 추계학술대회
• /
• pp.75-76
• /
• 2002

• 대한치과보철학회:학술대회논문집
• /
• 대한치과보철학회 2001년도 추계학술대회
• /
• pp.40-40
• /
• 2001