• Journal of the Korean Society for Precision Engineering
• /
• 제13권7호
• /
• pp.167-175
• /
• 1996

Work roll wear in the cold rolling of steel strip is strongly affected by rolling materials, rolling conditions and lubrication. Tests were performed to find the effects of rolling materials under the same lubricating conditions. Surface roughness of cold rolled steel strip as well as the coating technique itself is quite improtant in obtaining high image clarity of electronic products and car outer panels. Therefore this paper reviews for improvement of roughness and peak count about the surface of Cr coated work roll is investigated from the actual temper mill. The conclusions were obtained as follows; 1) Work roll wear in the cold rolling of steel strip is strongly affected by carbon contents of rolling materials, but there is not a separating force and total reduction ratio. 2) The roughness of strip surface is larger in the direction of width than in roll direction. 3) The electro-discharge textured roll has more uniform roughness distribu- tion than shot blasted roll and it's life time is two times longer than shot blasted because it has more harmonic wave roughness, and the higher peak count of surface roughness. 4) The life time of Cr coated work roll is 2 times longer than that of shot blasted work roll and variation of peak count, roughness and life time of Cr coated work roll is similar to electro-discharge texturing work roll. 5) The proper Cr coating thickness is 10 .mu. m at the work roll of temper mill.

• Tribology and Lubricants
• /
• 제14권2호
• /
• pp.35-41
• /
• 1998

The $WS_2$ solid lubricant synthesized through the vapour phase transport method was coated on the commercial bearing steel (SUJ 2) substrate, and the tribological behaviour of the lubricant was investigated using a ball-on-disk type tester. The $WS_2$ powder was spray-coated at room temperature using compressed air, and the change of friction coefficient was examined in various conditions, i.e., specimen configuration, atmosphere (air and nitrogen), applied load and rotating speed. $WS_2$ coated ball and disk showed the optimum friction coefficient of 0.07 and wear life of 45,000 cycles in the nitrogen atmosphere under 0.3 kgf and 100 rpm, whereas relatively high coefficient of 0.13 and reduced wear life of 4,000 cycles were observed in air atmosphere. The effect of rotating speed on the friction coefficient was not observed both in nitrogen and in air atmospheres. This confirmed that the spray-coated $WS_2$ solid lubricant was effective in reducing the friction coefficient and improving wear life in nitrogen atmosphere, and the oxygen and moisture existing in air could seriously deteriorate the lubrication effect of $WS_2$ coating layer.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 1989년도 제10회 학술강연회초록집
• /
• pp.41-58
• /
• 1989

현재 자동차엔진유를 비롯한 각종윤활유에 마찰마모방지제 및 산화방지제로 사용되고 있는 유용성 몰리부덴계 화합물은 윤활제의 첨가제로서 주목받고 있다. 이와 같은 유용성 몰리부덴계 화합물은 윤활제의 첨가제로서 마찰부분의 고온에 의해 열분해함으 2 유화몰리부덴($MoS_2$)을 생성하기 위해서 합성한 것이다. $MoS_2$는 마찰마모 감소제로서 잘 알려져 있지만 고체이기 때문에 마찰면에 COATING 하거나 윤활유에 분산시켜 사용하고 있다. 그러나 윤활유에 분산시키는 것과 마찰면에 흡착시키는 것과는 계면화학적 반대현상이므로 문제가 발생하게 된다. 그러므로 윤활유중에 안정한 분산계를 만들어 사용시에는 비교적 안정한 COLLOID 계가 파손되지 않아야 한다. 그러나 열가학적으로 불안정한 COLLOID 계를 유지하기는 어려운 문제이다. 그러므로 유용성인 몰리부덴계 화합물을 윤활유에 용해시켜 열적 혹은 TRIBOCHEMICAL 적으로 분해해 줌으로서 마찰표면에 $MoS_2$의 생성이 필요하다. 이와같은 목적으로 개발된 유용성 몰리부덴화합물은 마찰마모감소작용 및 산화방지작용의 메카니즘에 관해서는 불투명한 점이 많다. 본 논문은 유용성 몰리부덴계 화합물중 Molybdenum dialkyl dithiocarbamate (이후 MoDTC로 명함)를 윤활유 첨가제로 사용해 마찰실험을 통하여 마찰감소작용의 메카니즘을 해명하고, 특히 마찰표면에 생성될 $MoS_2$막의 효과에 관해 중점을 두고 분위기의 효과로 부터 MoDTC의 마찰감소작용의 인자에 대한 고찰을 행하였다.

• Journal of Surface Science and Engineering
• /
• 제44권6호
• /
• pp.269-276
• /
• 2011

Phase evolution and tribological behavior of Cr-Mo-N multi compositional films with different interlayer were investigated. The films were deposited by hybrid PVD (Physical Vapor Deposition) system consisted of dc unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) sources. A pure molybdenum (Mo) was used as sputtering target and also a pure Cr was used as AIP target to form the Cr-Mo-N films. Various growth planes were found, no textured surface, in all of the multi composition films. Maximum value of microhardness was measured in Cr-Mo-N film with Mo interlayer as 29 GPa. Composition film was mainly showed the aspect of the adhesive wear than CrN film. The friction coefficient was decreased from 0.6 for pure CrN coating to 0.35 for Cr-Mo-N film with Mo interlayer. This result may come from the formation of metal oxide tribo-layer which is known as solid lubricant during the wear test.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.96-102
• /
• 2001

plasma-sprayed Cr$_2$O$_3$-based coatings containing MoO$_3$ were studied to gain a better understanding of the influence of MoO$_3$ composition in the coatings on their tribological behaviour. A reciprocal type tribo-tester was employed to examine friction and wear behavior of the specimens at high temperature(450。C). The physical characteristics of worn surfaces were investigated by scanning electron microscopy and chemical composition of the coating surfaces was analyzed using a X-ray photoelectron spectrometer. The results showed that friction coefficient of the MoO$_3$-added coatings were lower than those without MoO$_3$ addition. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with MoO$_3$ addition. XPS analysis of the protecting layer indicated that MoO$_3$ composition was dominantly formed at the surface. MoO$_3$ composition in the protecting layer appears to be more favorable in reducing the friction.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.56-63
• /
• 2003

Micro/nano adhesion and friction properties of mixed self-assembled monolayer (SAM) with different chain length for MEMS application were experimentally studied. Many kinds of SAM having different spacer chains(C6, C10 and C18) and their mixtures (1:1) were deposited onto Si-wafer, where the deposited SAM resulted in the hydrophobic nature. The adhesion and friction properties between tip and SAM surfaces under nano scale applied load were measured using an atomic force microscope (AFM) and micro scale applied load were measured using ball-on-flat type micro-tribotester. Surface roughness and water wetting angles were measured with SPM (scanning probe microscope) and contact anglemeter. Results showed that wetting angles of mixed SAMs showed the similar value of pure SAMs. The coating surface morphology was increased as mixing of SAM. Nano adhesion and nano friction decreased as increasing of the spacer chain length and mixing of SAM. Micro friction was decreased as increasing of the spacer chain, but micro friction of mixed SAM showed the value between pure SAMs. Nano adhesion and friction mechanism of mixed SAM was proposed in a view of stiffness of spacer chain modified chemically and topographically.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.346-353
• /
• 2001

Zirconia powder containing 3 mol% yttria(3Y-PSZ) with and with out Fe$_2$O$_3$ addition was coated on tile cast iron substrate by plasma spraying method. The erosion experiments were performed at temperatures from $25^{\circ}C$ to $600^{\circ}C$. A gas blast type erosion tester was used to examine erosion behavior of the specimens. The results of 3Y-PSZ coatings showed that tile erosion rate had maximum value at 40$0^{\circ}C$. It coincided with tile results of phase transformation tetragonal phase to monoclinic phase caused by low temperature thermal degradation. The tensile stress relaxation and the micro-hardness improvement significantly influenced on the erosion rate at $600^{\circ}C$. In the case of Fe$_2$O$_3$ added 3Y-PSZ coatings, the erosion rate of tested at $25^{\circ}C$ showed maximum value at 5.0 mol% Fe$_2$O$_3$ added coating. This tendency is caused by the improvement of mechanical properties and the tensile residual stress. The erosion rate at 200'c and 400'L showed significantly decrease by Fe203 addition. This decrease is believed to be the stabilization of the tetragonal phase and the increase of micro-hardness.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.445-449
• /
• 2018

Chromium plating is a common surface treatment technique extensively applied in industry due its excellent properties which include substantial hardness, abrasion resistance, corrosion resistance, surface color, and luster. In this study, the effect of $MoS_2$ particles of the composite coating was investigated. To improve the lubrication of mold, $Cr-P-C/MoS_2$ composite plating was studied by varying the $MoS_2$ content. The current efficiency of the composite plating incorporated $MoS_2$ particles was increased at $MoS_2$ contents of 0.5 and 1.0 g/l due to the incorporation of fine particles. On the other hand, when the content of $MoS_2$ is 1.0 g/l or more, the current efficiency is lowered due to an increase in impact on the cathode surface. In order to evaluate the mechanical properties of Scratch test were conducted. Scratch test confirmed the lubricity and abrasion resistance characteristics revealed that the composite plating with added $MoS_2$ had relatively low surface roughness and uniform surface modification to improve its properties.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.77-77
• /
• 2017

Titanium and its alloys offer attractive properties in a variety of applications. These are widely used for the field of biomedical implants because of its good biocompatibility and high corrosion resistance. Titanium anodizing is often used in the metal finishing of products, especially those can be used in the medical devices with dense oxide surface. Based on SAE/AMS (Society of Automotive Engineers/Aerospace Material Specification) 2488D, it has the specification for industrial titanium anodizing that have three different types of titanium anodization as following: Type I is used as a coating for elevated temperature forming; Type II is used as an anti-galling coating without additional lubrication or as a pre-treatment for improving adherence of film lubricants; Type III is used as a treatment to produce a spectrum of surface colours on titanium. In this study, we have focused on Type II anodization for the medical (dental and orthopedic) application, the anodized surface was modified with gray color under alkaline electrolyte. The surface characteristics were analyzed with Focused Ion Beam (FIB), Scanning Electron Microscopy (SEM), surface roughness, Vickers hardness, three point bending test, biocompatibility, and corrosion (potentiodynamic) test. The Ti-6Al-4V alloy was used for specimen, the anodizing procedure was conducted in alkaline solution (NaOH based, pH>13). Applied voltage was range between 20 V to 40 V until the ampere to be zero. As results, the surface characteristics of anodic oxide layer were analyzed with SEM, the dissecting layer was fabricated with FIB method prior to analyze surface. The surface roughness was measured by arithmetic mean deviation of the roughness profile (Ra). The Vickers hardness was obtained with Vickers hardness tester, indentation was repeated for 5 times on each sample, and the three point bending property was verified by yield load values. In order to determine the corrosion resistance for the corrosion rate, the potentiodynamic test was performed for each specimen. The biological safety assessment was analyzed by cytotoxic and pyrogen test. Through FIB feature of anodic surfaces, the thickness of oxide layer was 1.1 um. The surface roughness, Vickers hardness, bending yield, and corrosion resistance of the anodized specimen were shown higher value than those of non-treated specimen. Also we could verify that there was no significant issues from cytotoxicity and pyrogen test.