• 한국화재소방학회논문지
• /
• 제31권3호
• /
• pp.19-24
• /
• 2017

인화점은 산업현장에서 화재 및 폭발의 위험성을 결정하는데 사용되는 중요한 지표의 하나로 안정성 평가 시 많이 사용되고 있다. 따라서 본 연구는 고무제조 공정에서 주로 쓰이는 이성분계 혼합물 중 {toluene+ethylbenzene}, {methlycyclohenxane+ethylbenzene} 그리고 {n-heptane+ethylbenzene} 대한 인화점을 101.3 kPa에서 SETA 밀폐식 인화점 측정기를 이용하여 측정하였다. 각 이성분계에 대하여 Raoult's의 법칙, Wilson, NRTL 및 UNIQUAC 파라미터를 이용하여 혼합물에 대한 인화점 예측하고 실험 결과와 비교하였다. 비교 결과 모든 예측값과 실험값은 유사한 값을 보였고 편차가 1.74 K이내의 결과를 보였다.

• 한국가스학회지
• /
• 제14권5호
• /
• pp.19-25
• /
• 2010

본 연구에서는 o-xylene+n-pentanol 및 m-xylene+n-hexanol 계의 인화점을 Tag 개방식 장치(ASTM D1310-86)를 이용하여 측정하였다. 실험값은 Raoult의 법칙, van Laar 및 Wilson 식을 이용한 계산된 값들과 비교하였다. 그 결과, 최적화법에 의한 예측값이 Rauolt의 법칙에 의한 계산 보다 실험값에 더욱 근접하였다. 또한, van Laar 식을 사용한 최적화법이 Wilson 식에 의한 최적화법 보다 실험값에 대한 모사성이 우수하였다.

• 한국의류학회지
• /
• 제18권5호
• /
• pp.595-601
• /
• 1994

This study was accomplished to investigate drape coefficient and wrinkle recovery of brushed fabrics according to treatment processes and brushing conditions. For this study, grey fabrics of blended ratio of polyester 65% : cotton 35% were bleached and dyed. These fabrics were then brushed 1, 3, 5 and 7 times. Drape coefficient and wrinkle recovery of brushed fabrics were measured by drape tester and shirley crease recovery tester respectively. The experimental results were analysed statistically to relate mechanical properties, handle, drapability, and wrinkle recovery 1) Drape coefficients of dyed fabric showed lower values and wrinkle recovery showed higher ones than those of bleached and dyed fabrics. Especially dyed fabric brushed 3 times showed good appearance and form stability. 2) Considering the blocked properties that contribute to the drape coefficient and wrinkle recovery of brushed fabrics, bending and shearing properties had a high degree of correlation with brushed fabrics, and 2HB/W showed a high positive correlation with drape coefficient and a high negative correlation with wrinkle recovery.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.899-903
• /
• 2009

Recently, research and development of the linear compressor are being active. The reason is that the one has not only higher efficiency than reciprocating type, but also lower noise. But because the dicharge valve of linear compressor is operated in high pressure and temperature circumstance, it is important to prevent leakeage. In this paper three other plastic reinforced composite materials were used. Those are TPI, PEEK and PEK which were containing other volume and kind of carbon fibers. First, for assessing mechanical properties, we measured the hardness and the heating property of the trst sepecimen by the microvickers hardness tester and the differential scanning calorimeter respectively. Finally, through FALEX tester, we could know the characteristics of the wear proving the results of before-conducted experiments.

• 한국화재소방학회논문지
• /
• 제32권1호
• /
• pp.1-6
• /
• 2018

인화점은 산업현장에서 액체의 화재 및 폭발 위험을 결정하는데 사용되는 가장 중요한 변수 중 하나로써 가연성 물질의 화재 위험성을 나타내는 지표이며 안정성 평가에 많이 사용되고 있다. 따라서 본 연구는 다양한 산업에서 용매로 사용되는 이성분계 혼합물 중 {methanol+toluene}, {ethanol+toluene} 그리고 {1-propanol+toluene}에 대한 인화점을 SETA 밀폐식 인화점 측정기를 이용하여 측정하였다. 각 이성분계 혼합물에 대한 인화점을 예측하기 위해 Raoult's의 법칙, Wilson, NRTL 및 UNIQUAC 파라미터를 이용하였고 실험 결과와 비교하였다. Raoult's의 법칙을 제외한 비교 결과, 모든 예측값과 실험값은 유사한 값을 보였고 편차가 1.69 K이내의 결과를 보였다.

• Elastomers and Composites
• /
• 제55권2호
• /
• pp.108-113
• /
• 2020

Wear particles of the model tread compounds for bus and truck tires were made using a laboratory abrasion tester and characterized based on their size distributions, shapes, and crosslink densities. The influence of the carbon black contents and rubber compositions (NR= 100 and NR/BR= 80/20) on the production of wear particles was investigated. The wear particles were separated according to size using a sieve shaker. The shape properties of the wear particles were analyzed using an image analyzer and scanning electron microscopy (SEM). Their shapes were observed as tiny stick cookies or sausages with bumpy surfaces. The particle size distribution tended to be smaller with increasing carbon black content. Moreover, the particle size distributions of the NR = 100 samples were larger than that of the NR/BR blend samples. There were different filaments in the wear particles. The filament diameters tended to be thinner with increasing carbon black content. The crosslink density increased with increasing carbon black content, and the crosslink densities of the NR= 100 samples were lower than those of the NR/BR blend ones. The particle size distribution tended to be smaller with increasing crosslink density. Based on the experimental results, the wear particles can be produced by detaching debris from the main body through repetitive strain and recovery.

• 청정기술
• /
• 제26권4호
• /
• pp.279-285
• /
• 2020

Laboratories and industrial processes typically involve the use of flammable substances. An important property used to estimate fire and explosion risk for a flammable liquid is the flash point. In this study, flash point data at 101.3 kPa were determined using a SETA closed cup flash point tester on the following solvent mixtures: {2,2,4-trimethylpentane + methylcyclohexane}, {2,2,4-trimethylpentane + ethylbenzene}, and {2,2,4-trimethylpentane + p-xylene}. The purpose of this work is to obtain flash point data for binary mixtures of 2,2,4-trimethylpentane with three hydrocarbons (methylcyclohexane, ethylbenzene, and p-xylene), which are representative compounds of the main aromatic hydrocarbon fractions of petroleum. The measured flash points are compared with the predicted values calculated using the GE models' activity coefficient patterns: the Wilson, the Non-Random Two-Liquid (NRTL), and the UNIversal QUAsiChemical (UNIQUAC) models. The non-ideality of the mixture is also considered. The average absolute deviation between the predicted and measured lower flash point s is less than 1.99 K, except when Raoult's law is calculated. In addition, the minimum flash point behavior is not observed in any of the three binary systems. This work's predicted results can be applied to design safe petrochemical processes, such as identifying safe storage conditions for non-ideal solutions containing volatile components.

• Tribology and Lubricants
• /
• 제39권1호
• /
• pp.13-20
• /
• 2023

Large drill bits may face high hardness ore and high working pressure when working. To optimize the use effect of large drill bits and prolong the use time, it is necessary to add a layer of pressure-resistant, wear-resistant, and low-friction coating on the surface of the drill bit. In this study, CoCrNiAlTi high-entropy alloy coatings and CoCrNiAlTi (70 wt%)-TiC (30 wt%) composite coatings are successfully prepared on Q235 steel by plasma spraying. The CoCrNiAlTi (70 wt%)-TiC (30 wt%) coating consists of FCC solid solution and a small amount of TiC phase. The effect of TiC on the composition phase, microhardness, and elastic modulus of HEA coating is studied by X-ray diffractometer (XRD) and microhardness tester. The effect of TiC on the friction and wear properties of HEA coatings is investigated using a wear tester. By improving the process parameters, the metallurgical bonding between the coating and the substrate is well combined, and a coating without pores and cracks is obtained. The experimental results confirm that the microhardness, elastic modulus, and wear resistance of CoCrNiAlTi-TiC composite coating are better, and the friction coefficient is lower.

• 한국안전학회지
• /
• 제31권4호
• /
• pp.42-47
• /
• 2016

The combustible properties(flash point, explosion limit and autoignition temperature) are the important safety items which are considered in the typical MSDS(material safety data sheet). In this study, for the safe handling of n-butyl methacrylate(n-BMA) being used in various ways in the chemical industry, the flash point and the autoignition temperature(AIT) of n-butyl methacrylate was experimented. And, the lower explosion limit of n-butyl methacrylate was calculated by using the lower flash point obtained in the experiment. The flash points of n-butyl methacrylate by using the Setaflash and Pensky-Martens closed-cup testers measured $44^{\circ}C$ and $51^{\circ}C$, respectively. The flash points of n-butyl methacrylate by using the Tag and Cleveland open cup testers are measured $53^{\circ}C$. The AIT of n-butyl methacrylate by ASTM 659E tester was measured as $295^{\circ}C$. The lower explosion limit by the measured flash point $44^{\circ}C$ was calculated as 0.85 vol.%. It was possible to predict lower explosion limit by using the experimental flash point or flash point in the literature.

• 한국주조공학회지
• /
• 제39권6호
• /
• pp.103-109
• /
• 2019

Cu-added SKD11 was manufactured through the casting process and the effects of Cu addition with different contents (0, 1, 2 and 3 wt%) and aging treatment on microstructure, mechanical characteristics such as tensile strength and hardness, and thermal conductivity were investigated. The microstructure was analyzed by FE-SEM and XRD, the mechanical characteristics by Rockwell hardness tester and Tensile tester, and the thermal conductivity by Laser flash. As a result, SKD11 containing Cu had higher hardness than as-received SKD11. The hardness of as-cast SKD11 containing 1 wt% Cu was 42.4 HRC, whereas the hardness of asreceived SKD11 cast alloy was 19.5 HRC, indicating that the hardness was greatly improved when Cu was added. In the case of tensile strength, Cu-added SKD11 cast alloy had lower tensile strength than as-received SKD11, and the tensile strength tended to increase as Cu content increased. After heat treatment, however, tensile strength of as-received SKD11 was significantly increased, whereas in the case of Cu-added SKD11, as the Cu contents increased, the tensile strength increased less and even reduced at 3 wt% Cu. The thermal conductivity of Cu-added SKD11 cast alloy was about 13 W m^-1 K^-1, which was lower than that of the asreceived SKD11 cast alloy (28 W m^-1 K^-1). After the heat treatment, however, the thermal conductivity of as-received SKD11 was reduced, while the thermal conductivity of the SKD11 added with Cu was increased. Thermal conductivity was generally larger with less Cu content, and this tendency became more pronounced after heat treatment.