• 한국농공학회지
• /
• 제24권4호
• /
• pp.57-68
• /
• 1982

The paddy fiels slope located in Kangweon province Hwyongsung gun Gonggeun myon Shinchonri was considerably steep and so it was impossible to economically consolidate the field up to date. But for the porpose of farm mechanization, the field (32. 27ha) was consolidated by the auther under the assitance of the Ministry of Agriculture and Fishery and,;the Administration of Kangweon province. This paddy field consolidation was caused by the treatise on "Land-consolidation methods for farm mechanization in the steep-sloped paddy field", of which the auther is the same. The constrution was carried out from September, 1981 to April, 1982. During the 4esign and construction, some Peculiarities were found and discussed. That is, in design, besides the common condititions for a design, some special conditions were considered and written below; (1) The ranges of field slope in this design were 1/100-1/30. (2) Long sides of the land readjustment blocks must be arranged abreast contour line, and so they make the amount of cutting and banking decreased so as to take the maximum advantage of the configuration of the field. (3) In design, the main principles of dividing blocks were written below; i) First of all, long side of a block should be drawn straight abreast a contour line. ii) Long side of a block should arrange abreast contour line and make its length 100-150m, if not, l)reak the side in order to make a bended rectangle. iii) Length of a short side should be determinded within differences of elevation (0.6 -1. 2m) between the two adjacent blocks toward the normal to a contour line. iv) Length of a short side should be above 15m and the ratio of long and short side should be slso kept 1: (4-6). v) A new field surface leveling was determinded from the elevation which produce the least amount of cuttingand banking within the range of 0.6-1. 2m diffe rences of elevation between the two adjacent blocks. vi) In the course of dividing blocks with the same width along the line which was normal to a contour line, all blocks connot keep their shape in a retangle because of steep slope of the field and so on, and so it was also necessory to make some non-retanglar and small blocks such as a trianglar or trapezoidal shape, which was impossible to use some of farm machinery. But because this non-rectanglar and small blocks were divided, larger and many rectanglar blocks can be divided and construction cost can also be lowered. According to the conditions discussed above, the paddy field consolidation project designed and constructed. And the results of this study were obtained as below; (1) Three-forth of total cost of this paddy field consolidation was not construction cost, and these cost consist of land grading (1/4), road and canal construction cost (1/4) and the other cost (1/4) such as surveying or materials and 56 on. (2) The steeper the land slope, the greater cost was assigned for road and canal construction, and than land grading. (3) Curtailment of the road and canal construction cost depended on simplificating their strutures. (4) In the case of the land slopes were low, the land grading cost was high by 1: 1.4 in comparison with the road and canal construction cost, and conversely when the slops were steep, the road and canal construction cost was high by 1 : 5 in compa- rison with the land grading cost. (5) The densities of irrigation canal, drainage canal and trunk and branch road were 150. Sm/ha, 60. im/ha and 17. 4m/ha respectively. The density of irrigation canal of the area was high by 2 times in comparison with the average one of Kangweon Province, and the others were nearly the same. (6) Most farmers (above 85%) knew the effects of paddy field consolidation. The effects are; 1) Improvement of irrigation 2) Improvement of farm management 3) Improvement of transportarion 4) farm mechanization and 5) grouping of the scattered land. And the more farm modernization was accomplished by these projects, the more farmers wanted to live in their land. (7) In spite of the very steep sloped paddy field, the diminution rate of the net farm land caused by consolidation was 7.7% which was nearly the same as the one of Chulweon plain of Kangweon province. Land grading cost was 971, OOOwon/ha which was rather cheap by 13.2% than the one of Ghulweon plain, and unit construction cost was 5, 341, OOOwon/ha (included soil addition) which was also nearly the same as the one of Chulweon plain and FNFIA (The federation of national farmland improvement association).

• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 농업과학연구
• /
• 제4권2호
• /
• pp.126-140
• /
• 1977

제주도(濟州道)와 남부(南部) 도서지방(島嶼地方)에서 한해(寒害) 및 풍해(風害)에 대한 감귤(柑橘)의 안전재배(安全栽培)와 남부지방(南部地方)에서 비닐하우스 피복(被覆)및 비닐 하우스 피복재배(被覆栽培)를 효율적(效率的)으로 수행(遂行)하기 위하여 온주밀감(溫州蜜柑)의 내한성(耐寒性) 품종(品種)의 선발(選拔), 내한성(耐寒性) 조기검정(早期檢定) 및 내한재배기술(耐寒栽培技術)에 관한 연구(硏究)를 실시한 바 결과(結果)를 다음과 같이 적요(摘要)한다. 1. 거치로 피복(被覆)한 비닐하우스에서 월동후(越冬後) 무동해개체(無凍害個體)를 내한성(耐寒性) 조기검정(早期檢定)(leaf freezing test)에 공시(供試)한 결과(結果) $-9^{\circ}C$ 저온(低溫)에 2시간(時間) 처리(處理)하여 건전개체(健全個體) 12, 약간동해개체(若干凍害個體) 15로 나타났다. 2. 비닐하우스에 거치 두겹을 피복(被覆)하고 상면(床面)에 벼짚 멀칭과 낮에 채광(採光)하는 조건에서 기온(氣溫) $-15^{\circ}C$ 내외(內外)(대전지방(大田地方))에서 하우스 내부(內部) 온도(溫度)는 $-3^{\circ}C$, 지온(地溫)은 $0^{\circ}C$ 이상(以上)으로 유지되었다. 3. 하우스내(內) 비닐 터널 설치(設置) 상면(床面) mulching은 모두 유의성있게 보온 효과를 나타냈으나, 외부 기온에 따라 다르며, 하우스내(內) 비닐 터널은 필림의 색(色)에 의한 유의차는 없었다. 4. 하우스 내부(內部)의 수직적 온도(溫度) 분포(分布)는 하우스내(內)의 온도(溫度)가 높을 때는 상부(上部)일수록 온도(溫度)가 약간 높았고 하우스 내(內)의 온도(溫度)가 낮을 때에는 중앙부(中央部) 상면(床面), 상부(床部)의 순서(順序)로 낮았다. 5. 하우스 내부(內部)의 수평적(水平的) 온도(溫度) 분포(分布)는 북면(北面)이 지온(地溫) 및 상면온도(床面溫度)가 낮고 그 밖의 동서남북(東西南北)의 가장자리 부분(部分)은 모두 낮아서 공시목(供試木)이 동해(凍害)를 받았으며 북쪽 벽면(壁面)에서 30cm내(內)의 공시목(供試木)은 동해(凍害)가 심했다. 6. 북면(北面) 바깥쪽 벽면하(壁面下)에 $30{\times}30{\times}30cm$의 짚다발 절록구(絶綠溝)의 설치(設置)는 북면(北面)의 지온(地溫) 및 상면(床面) 온도(溫度) 강하(降下)를 막아서 동해(凍害)를 막는 효과(效果)가 기대(期待)된다. 7. 흐린날, 눈 나린 날은 하우스 내외(內外)의 온도(溫度) 차이(差異)가 적었으나 방열이 적어서 내부(內部) 온도(溫度)는 야간(夜間)에도 비교적 높게 유지되었다. 8. 1일중 최고온도(最高溫度)의 peak는 하우스 내외(內外) 모두 15시(時) 전후(前後)에 있고 최저온도(最低溫度)의 peak는 모두 6시(時) 전후(前後)에 있으며 외부(外部) 온도(溫度)의 최저(最低)에 따라 내부(內部)도 변한다. 맑은 날의 최고온도(最高溫度)는 차(差)가 크고($19^{\circ}C$, 11월하순(月下旬)) 눈오는 날, 흐린 날은 차(差)가 적었으로($9^{\circ}C$, 11월하순(月下旬)) 특히 눈온 날 하우스내(內)의 온도(溫度) 강하(降下)가 적어서 야간(夜間)에 온도곡선(溫度曲線)은 평행(平行)에 가까왔다. 9. 내한성(耐寒性), 반왜성(半矮性)(semi-dwarf type), 단지형(短枝形)(spur type) 우량품종(優量品種)을 효과적(效果的)인 방한(防寒) 피복(被覆) 재배(栽培)의 기술(技術)을 적용(適用)한다면 제주도(濟州島) 및 남부지방(南部地方)에서의 감귤(柑橘)의 안전재배(安全栽培)와 재배(栽培) 면적(面積)의 확대(擴大)가 기대(期待)된다.

• 한국농공학회지
• /
• 제15권3호
• /
• pp.3059-3088
• /
• 1973

본연구(本硏究)에서는 연구(硏究)의 대상(對象)을 저습답(低濕畓)에 두기보다는 지하수위(地下水位)가 낮은 점질토(粘質土)의 건답(乾畓)에 두고 이 점질토(粘質土)논에 대(對)한 수잉전(移秧前)의 처리(處理)에 있어서 심경(深耕)을 한 것 답면(畓面)을 건조(乾燥)시켜 구열발달(龜裂發達)을 기(期)하게한 것 및 암거(暗渠)가 설치(設置)된 곳에서의 답면(畓面)을 건조(乾燥)시켜 구열발달(龜裂發達)을 기(期)하게 한 것 중에서 어떤 처리방법(處理方法)을 적용(適用)한 것이 뿌리신장(伸長)이 심층화(深層化)되여 벼의 수량(收量)을 높일 수 있고 동시(同時)에 지하배수기능(地下排水機能)이 제대로 발휘(發揮)되여 수확작업(收穫作業)에 대형기계(大型機械)를 도입(導入)하였을 때 농업기계(農業機械)의 주행성면(走行性面)에서 유리(有利)한가를 발견(發見)코저 한 것이다. 그래서 시험구처리(試驗區處理)에 있어서는 (1)이앙(移秧) 39일전(日前)에 경운(耕耘)하여 풍건(風乾)시킨 것(경운구(區)) (2) 이앙(移秧) 39일전(日前)에 경운(耕耘)하여 물로 포화(飽和)시켜 쓰린후(後) 구열(龜裂)을 발생(發生)시켜 이앙(移秧) 2일전(日前)에 15cm 깊이로 경운(耕耘)한 것(균열구(區)) (3) 이앙(移秧) 39일전(日前)에 암거설치(暗渠設置)와 동시(同時)에 경운(耕耘)하여 물로 포화(飽和)시켜 쓰린후(後) 구열(龜裂)을 발생(發生)시켜 이앙(移秧) 2일전(日前)에 15cm 깊이로 경운(耕耘)한 것(균암구(區))의 3요인(要因)에 15cm. 25cm, 35cm 깊이의 3수준(水準)으로 하고 15cm 깊이 경운구(區)를 Control구(區)로 정(定)하였는데 이에 의(依)하여 얻은 시험결과(試驗結果)는 대략(大略) 다음과 같이 요약(要約)될 수 있다. 1. 소비수량(消費數量)은 균암구(區)에 있어서는 경운구(區) 및 균열구(區)보다도 소비수량(消費水量)을 나타냈다. 따라서 유효우량은 균암구(區)에서 가장 크고 경운구(區), 균열구(區)의 순(順)으로 작은값을 나타냈고 순용수량(純用水量)에 있어서는 여전(如前)히 균암구(區), 경운구(區), 균열구(區)의 순(順)으로 작어저 균암구(區)가 가장 큰 양(量)을 나타냈다. 심도(深度)에 불구(不拘)하고 순용수량(純用水量)의 크기는 균암구(區)에서 105cm 내외(內外), 경운구(區)에서 70cm 내외(內外), 균열구(區)에서는 45cm 내외(內外)를 나타냈다. 2. 뿌리중량(重量)이 구열최대심도(龜裂最大深度)에 예민(銳敏)하게 영향(影響)을 받고 있는 경향(傾向)으로 미루어 볼 때 뿌리 발달(發達)은 답면상(畓面上)의 구열(龜裂)에 의(依)하기 보다는 구열심도(龜裂深度)에 더 큰 영향(影響)을 받는 것으로 되어 있다. 따라서 깊은구(區)일수록 뿌리중량(重量)은 커지는 경향(傾向)을 가졌고 처리간(處理間)에는 균열구(區), 균암구(區), 경운구(區) 순(順)으로 증대(增大)하는 경향(傾向)을 가졌다. 3. 초장(草丈)의 신장(伸長)에 있어서는 어느구(區)를 막론(莫論)하고 생육초기(生育初期)(분얼최성기(分얼最盛期))에는 별(別)로 차이(差異)를 발견(發見)할 수 없으나 생육중기(生育中期)(분얼종료기(分얼終了期)부터 유수형성기(幼穗形成期) 사이에서는 심도(深度)가 깊은구(區)일수록 그 성장(成長)이 떨어지고 생육후기(生育後期)(수잉기)(穗잉期)에 접어들면서 부터는 도리여 심도(深度)가 깊은구(區)가 얕은구(區)보다 더 왕성(旺盛)한 신장(伸長)을 하였다. 이것은 시험처리별(試驗處理別)로 볼 때 생육중기(生育中期) 이후(以後) 균열구(區)는 어느 다른 구(區)보다 떨어지고 균암구(區)와 경운구(區) 간(間)에는 별차이(別差異)는 없으나 균암구(區)가 여간(與干) 초장신장(草丈伸長)이 우세(優勢)한 경향(傾向)을 나타냈다. 4. 경수(數)에 있어서는 전생육기간(全生育期間)을 통(通)하여 심도(深度)가 깊은구(區)일수록 그 수(數)가 적어지는 경향(傾向)을 나타냈고 이것을 시험처별(試驗處別)로 볼 때 균열구(區)는 늘 균암구(區)와 경운구(區)보다 떨어졌으며 또 경운구(區)는 균암구(區)보다 약간(若干) 우세(優勢)한 경향(傾向)을 나타냈다. 5. 수량(收量)(조곡중)(租穀重))에 있어서는 시험처리별(試驗處理別) 각(各) 시험구(試驗區)의 수량(收量)을 Control 구(區) 15-경운구(區)와 대비(對比)할 때 35-경운구(區)에 있어서는 17%, 35-암거구(區)에 있어서는 10% 기타구(其他區)에 있어서는 모두 Control구(區)와 같거나 떨어졌다. 그리고 전체적(全體的)으로 볼 때 심도(深度)가 깊은구(區)일수록 수량(收量)은 증가(增加)하였고 경운구(龜)는 균암구(區)보다, 균암구(區)는 균열구(區)보다 수량(收量)이 높았으며 심도구(深度區)에는 1%의 유의성시험처리(有意性試驗處理)에는 5%의 유의성(有意性)이 존재(存在)하였다. 6. 조곡중(粗穀重)에 더 많은 영향(影響)을 주는 감수심(減水深)은 후기감수심(後期減水深)이며 15cm 구(區)에서는 2.7cm/day 이내(以內)에서 25cm 구(區)에서는 3.0cm/day 이내(以內)에서 35cm 구(區)에서는 3.3cm/day이내(以內)의 범위(範圍)에서 감수심(減水深)이 증대(增大)하면 조곡중(粗穀重) 증대(增大)하였고 동시(同時)에 동일감수심(同一減水深)에서는 심도(深度)가 깊은구(區) 일수록 조곡중(粗穀重)은 증대(增大)하였다. 따라서 동일감수심도(同一減水深度)가 깊은구(區)일수록 수량면(收量面)에서 유리(有利)함을 암시(暗示)하고 있다. 7. 뿌리중량(重量)에서 비례(比例)하여 조곡중(粗穀重)은 증대(增大)하였으며 벼뿌리중량(重量)이 동일(同一)할때는 심도(深度)가 깊은구(區)일수록 조곡중(粗穀重)은 증대(增大)하는 경향(傾向)을 보여주고 있다. 또 시험처리별(試驗處理別)로 볼 때는 벼뿌리 중량(重量)은 균열구(區), 균암구(區), 경운구(區)의 순(順)으로 컸고 따라서 조곡중(粗穀重)도 역시(亦是) 같은 순(順)으로 컸다. 그리고 조곡중(粗穀重)은 중간낙수기간(中間落水期間)의 최소함수비(最少含水比)와 그때의 평균지온(平均地溫)에 관계(關係)되나 함수비(含水比)가 40%이하(以下)에서는 평균지온(平均地溫)은 함수비(含水比)에 비례(比例)하여 증가(增加)하는 경향(傾向)이 있음으로 주(主)로 최소함수비(最小含水比)에 영향(影響)을 받는바가 크다. 8. 짚조곡중비(粗穀重比)는 심도(深度)가 얕은구(區)일수록 커지는 경향(傾向)을 보였고 또 벼뿌리중량(重量)에 역지수함수적(逆指數函數的)으로 증대(增大)하였다. 또 같은 심도(深度)의 구(區)에서는 15cm 구(區)를 제외(除外)하고는 짚조곡중비(粗穀重比)는 감수심(減水深)에 비례(比例)하여 증대(增大)하였다. 감수심(減水深)이 어느 한도(限度)까지 증대(增大)됨에 따라 조곡중(租穀重)이 증대(增大)하지만 동시(同時)에 짚조곡중비(粗穀重比)도 증대(增大)함을 보여주고 있다. 9. 동일토성(同一土性)에서 구열량(龜裂量)은 기상조건(氣象條件) 특(特)히 증발량(蒸發量)의 증대(增大)에 따라 증대(增大)하며 답면건조도중(畓面乾燥途中)에 강우(降雨)가 있으면 답면구열량(畓面龜裂量)은 현저(顯著)히 감소(減小)한다. 점질토(粘質土)의 구열량(龜裂量)은 대체(大體)로 함수비(含水比)가 25% 이상(以上)에서는 함량비(含量比)에 역지수적(逆指數的)으로 증가(增加)하는 경향(傾向)을 보였고 구열(龜裂)의 최대(最大) 심도(深度)는 31% 이하(以下)의 함수비(含水比)에서는 일정(一定)한 값을 유지(維持)하는 경향(傾向)이있다. 10. Cone 지수(指數)는 어느 한도(限度)까지는 구열량(龜裂量)에 비례(比例)하는 경향(傾向)이있으나 구열량(龜裂量)이 어느 한도(限度)를 넘으면 약간(若干) 구열량(龜裂量)에 역비례(逆比例)하는 경향(傾向)을 보여주고 있다. 그 한도(限度)의 함수비(含水比)는 25% 근처가 될 것이다. 11. 최종낙수후 (最終落水後)의 Cone 지수(指數)의 경시적(經時的) 증대(增大)는 생육후기(生育後期)의 감수심(減水深)에 비례(比例)하는 경향(傾向)을 보였고 동일감수심(同一減水深)에서 균암구(區)는 다른 두 구(區)보다 큰Cone지수(指數)를 나타냈고 경운구(區)는 심도(深度)가 깊은구(區)일수록 균열구(區)보다 작은 Cone 지수(指數)를 나타냈는데 특(特)히 35-경운구(區) Cone의 지수(指數)는 현저(顯著)하게 작은 값을 나타냈다. 12. 최종낙수후(最終落水後)의 답면건조(畓面乾燥)에 있어서는 함수비(含水比)의 감소상황(減少狀況) 및 Cone 지수(指數)의 증대상황(增大狀況)에 비추어 볼 때 시험처리별(試驗處理別)로는 균암구(區)가 다른 두 구(區)보다 밟르고 경운구(區)는 가장 늦어지고 심도(深度)가 깊은 구(區)에서는 더욱 늦어지고 있다. 농업기계(農業 機械)의 주행(走行)에 지장(支障)을 가져오지 않을 정도(程度)의 Cone 지수(指數)($2.5kg/cm^2$)로 답면건조(畓面乾燥)를 시키자면 최종낙수시기(最終落水時期)를 잡는 시기(時期) 및 낙수기간(落水期間)동안의 강우(降雨)의 유무(有無)에 따라 다르게지만 강우(降雨)가 전혀 없다면 누계계기증발량(累計計器蒸發量)을 기준(基準)으로 잡을 때 균암구(區)에서는 누계계기증발량(累計計器蒸發量)으로 약(約) 44mm가 필요(必要)하고 기타구(其他區)에서는 50mm 이상(以上)이 필요(必要)하게 됨으로 균암구(區)에서의 답면건조진행(畓面乾燥進行)은 대체(大體)로 경운구(區), 균열구(區)보다 2일이상(日以上)이 빠르며 35-경운구(區)와 비교(比較)하면 5일(日) 이상(以上)이나 빠르게 될 것이다.

• 대한자원환경지질학회:학술대회논문집
• /
• 대한자원환경지질학회 2001년도 제17차 공동학술강연회 및 춘계학술답사
• /
• pp.42-63
• /
• 2001

무령왕릉의 보존대책을 수립하기 위하여 누수 현상, 고분구조 벽체거동 상황 및 구조안전점검, 고분 내에 서식하는 조류의 제거, 고분내 습기 및 결로현상 제거를 위한 공기조화시설 등을 포함하는 종합 정밀저사를 1996년 5월 1일 부터 1997년 4월 30일 까지 1년간 수행하였다. 이러한 연구를 수행하기 위하여 기초 지반에 대한 정밀측량, 고분 내외부의 년중 온습도 모니터링, 지반의 내부물성 파악을 위한 지구물리 탐사, 시추 자료에 대한 각종 물성실험, 지반의 투수계수 측정 및 지구화학적 분석을 실시하였다. 고분 내외부에 대한 정밀측량 결과 봉분 중심의 현실 중심보다 북동쪽으로 5m 이격되어 있다. 무령왕릉의 경우는 발굴 당시에도 유사한 분포를 하였으나, 이로 인하여 불균형적인 토압을 발생시키는 원인이 되고 있다. 벽돌깨짐 상황 조사결과 무령왕릉의 조사 대상 벽돌 6025장중 1972년에는 435장 파손되었던 것이 1996년 조사결과 1072장이 파손된 것으로 밝혀져 파손율이 2.5배로 증가하였다. 6호분의 경우는 이보다 더 심하여 벽돌 파손율이 2.9배로 증가하고 있다. 1972년 상황은 약 1450년간 진행된 것이고 1996년의 상황은 불과 24년간 진행된 것임을 감안할 고분이 발굴된 이후 벽돌의 균열은 상당한 가속도로 진행되어 온것이 사실이며 이대로 진행된다면 더욱 더 가속화될 것으로 판단된다. 고분벽체의 거동상태를 계측한 결과 무령왕릉 동측벽의 경우 우기와 건기에 각각 2.95 mm/myr및 1.52 mm/myr의 거동을 보여 우기에 지하수 유입에 의한 지반의 약화로 인하여 건기보다 2배정도 거동하는 양상을 보인다. 한편, 연도 입구의 호벽은 건기에 전실쪽으로 0.43 mm/myr, 연도쪽으로 2.05 mm/myr의 거동을 보여 무령왕릉에서는 가장 심한 거동을 보이고 있다. 6호분의 거동현황은 건기에만 측정된 바, 현실의 동측벽과 서측벽이 각각 벽체 뒤쪽으로 7.44 mm/myr, 현실안쪽으로 3.61 mm/myr의 거동을 보여 조사대상 5호분, 6호분, 7호분, 중 가장 심한 거동을 보이고 있다. 이는 고분 벽돌의 깨짐이 6호분이 가장 심하다는 사실과 무관하지 않은 것으로 판단된다. 봉분내부의 토양층구조에 대한 지오레이다 영상단면을 분석한 결과 무령왕릉 연도상부의 누수지방지층이 심하게 균열되어 있음을 발견하였다. 이 곳은 고분내부로 직접누수가 발생하는 곳이다. 직접누수와 지하수 형태로 유입된 침투수는 고분군 주위의 지반의 함수비를 증가시켜 지반의 지지력을 약화시키고 또한 고분내로 서서히 유입되어 고분내부의 습도를 100%로 유지시키는 주된 원인이다. 이러한 높은 습도는 고분내의 남조류의 번식을 가져왔으며 남조류의 번식은 현재 6호분이 가장 심각하고 7호분이 우려되는 수준이며 5호분은 문제가 없는 것으로 판단된다. 이와 같이 고분군의 발굴후 인위적인 환경변화와 지속적인 강우침투 및 배수 불량의 영향은 고분군의 안정성에 상당한 위험을 초래하였으며, 현 상태는 각 고분에 대한 보강이 불가피한 것으로 판단된다. 고분 벽돌의 깨짐, 고분 벽체의 거동, 조류의 서식등을 포함하여 송산리 고분군에서 발생되고 있는 보존상의 제반 문제점들을 일차적으로 누수 및 침투수에 의한 결과이다. 그러므로 무엇보다도 고분군 내부 및 고분 주변으로의 강우 및 지하수 침투를 막는 차수 대책이 시급한 것으로 판단된다. 또한 이미 발생한 변위가 더 이상 진행되지 않도록 하중을 경감하고 토압의 균형을 이루는 보강대책이 시급한 실정이다. 고분군의 보존대책으로는 고분의 구조안전에 관하여 근본적인 구조변경이 불가피한 직접 보강대책보다 간접적인 보강대책이 바람직한 것으로 판단된다. 간접적 보강대책으로서는 현 봉분규모의 축소, 불균등토압의 조정, 강우침투 방지를 위한 최종복토시스템, 유도배수구의 설치 및 능선 상부로부터의 지하수 차단시설을 포함한다. 이러한 차수대책은 고분군의 제문제를 해결하는 가장 근본적인 대책이라 할 수 있다. 고분내 결로현상 및 습기 제거를 위하여 항온항습장치를 전실에 설치하고 덕트를 통하여 고분내 현실로 순환시키는 방법을 제안하며 외부 온도의 영향을 덜 받게 하기 위하여 전실상부 토양을 현재보다 두껍게 하고 전실의 천정마감재를 열전도도가 낮은 목재로 교체하며 출입문의 이동등을 제안하였다. 금번 조사 연구를 통하여 얻어진 각종 보수 및 보존대책은 고분구조 자체에 가능한 한 최소의 변화를 주면서 가장 시급한 문제점부터 해결하도록 제시되었다. 설계 및 시공단계에서는 보수의 경중을 가려 순서에 입각하여 이루어져야만 하며 설계 및 시공단계에서 고분의 구조안전에 영향을 주지 않도록 각별한 주의가 요망된다. 끝으로, 상기의 보수대책이 실시된 후 이에 대한 평가 및 향후의 영구 보존을 위한 벽체경사 계측, 함수비 및 지하수위 계측, 온습도 측정 등을 포함하는 사후계측시스템은 필수적이라 할 수 있다. 각종 계측자료를 이용한 장기적이고도 세심한 분석을 통하여 완벽한 보존 관리가 이루어져야할 것으로 사료된다.로 사료된다.