• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.185-193
• /
• 2015

Ultra high performance concrete (UHPC) has been developed to overcome the low tensile strengths and brittleness of conventional concrete. Considering that UHPC, owing to its composition and the use of steel fibers, develops a compressive strength of 180 MPa as well as high stiffness, the top flange of the steel girder may be superfluous in the composite beam combining a slab made of UHPC and the steel girder. In such composite beam, the steel girder takes the form of an inverted-T shaped structure without top flange in which the studs needed for the composition of the steel girder with the UHPC slab are disposed in the web of the steel girder. This study investigates experimentally and analytically the flexural behavior of this new type of composite beam to propose details like stud spacing and slab thickness for further design recommendations. To that goal, eight composite beams with varying stud spacing and slab thickness were fabricated and tested. The test results indicated that stud spacing running from 100 mm to 2 to 3 times the slab thickness can be recommended. In view of the relative characteristic slip limit of Eurocode-4, the results showed that the composite beam developed ductile behavior. Moreover, except for the members with thin slab and large stud spacing, most of the specimens exhibited results different to those predicted by AASHTO LRFD and Eurocode-4 because of the high performance developed by UHPC.

• Economic and Environmental Geology
• /
• v.54 no.1
• /
• pp.105-115
• /
• 2021

The geological CO2 sequestration in underground geological formation such as deep saline aquifers and depleted hydrocarbon reservoirs is one of the most promising options for reducing the atmospheric CO2 emissions. The process in geological CO2 sequestration involves injection of supercritical CO2 (scCO2) into porous media saturated with pore water and initiates CO2 flooding with immiscible displacement. The CO2 migration and distribution, and, consequently, the displacement efficiency is governed by the interaction of fluids. Especially, the viscous force and capillary force are controlled by geological formation conditions and injection conditions. This study aimed to estimate the effects of surfactant on interfacial tension between the immiscible fluids, scCO2 and porewater, under high pressure and high temperature conditions by using a pair of proxy fluids under standard conditions through pendant drop method. It also aimed to observe migration and distribution patterns of the immiscible fluids and estimate the effects of surfactant concentrations on the displacement efficiency of scCO2. Micromodel experiments were conducted by applying n-hexane and deionized water as proxy fluids for scCO2 and porewater. In order to quantitatively analyze the immiscible displacement phenomena by n-hexane injection in pore network, the images of migration and distribution pattern of the two fluids are acquired through a imaging system. The experimental results revealed that the addition of surfactants sharply reduces the interfacial tension between hexane and deionized water at low concentrations and approaches a constant value as the concentration increases. Also it was found that, by directly affecting the flow path of the flooding fluid at the pore scale in the porous medium, the surfactant showed the identical effect on the displacement efficiency of n-hexane at equilibrium state. The experimental observation results could provide important fundamental information on immiscible displacement of fluids in porous media and suggest the potential to improve the displacement efficiency of scCO2 by using surfactants.

• Korean Journal of Veterinary Research
• /
• v.12 no.1
• /
• pp.25-35
• /
• 1972

The author used a dog preparation, in which either the left lung or the lower left lobe rebreathed continuously from a bag, to compare $CO_2$ and $O_2$ tensions in the rebreathed gas with those in blood entering or leaving the lung. In the 10 dogs studied, alveolar pressures for both gases were greater than in the blood; the "upstream" gradient (alveolar pulmonary arterial blood) exceeded the "downstream" gradient (alveolar-pulmonary venous blood) for both gases, but the difference was only significant for $CO_2$. The author attributed this effect to the production of $CO_2$ in lung tissue metabolism and its uptake by the blood. The difference in $CO_2$ tension between blood leaving and entering lung increased while the downstream gradient fell, an effect which was independant of the level of anesthesia. There was no evidence of a fall in base excess in blood passing through the lung, as would occur from the production of metabolic acids during anaerobic metabolism at the low levels found in the rebreathing lung in this preparation.

• Journal of Acupuncture Research
• /
• v.28 no.6
• /
• pp.1-17
• /
• 2011

Objectives : This study aimed to review randomized controlled trials of acupuncture performed in South Korea that used sham acupuncture as a control group. Methods : The following databases were searched through the end of September 2011: Koreanstudies information service system (KISS), Korean medical database (KMbase), national discovery OR science leaders (NDSL), oriental medicine advance searching integrated system (OASIS), and research information service system (RISS). The following search terms were used: acupuncture AND (sham or placebo). The reference lists of searched articles and Korea institute of oriental medicine (KIOM) reports(2005~2009) were identified. The following data were extracted: year/first author, disease, number of participants, blinding, intervention, outcome, and result. Where appropriate, we performed meta-analysis. The methodological quality was assessed according to the Jadad scale and 'risk of bias' by Cochrane Handbook procedure. Results : Twenty-nine studies were included in this review. In eighteen studies, penetrating sham controls were used as the control intervention, whereas the remaining eleven studies adopted non-penetrating sham controls such as the Park Sham Device or blunt auricular acupuncture. Nine studies showed statistically significant difference in outcomes. Twelve studies concerning insomnia after stroke, chronic tension-type headache, idiopathic Parkinson's disease, Hwa-Byung, and smoking cessation were included in meta-analysis. A meta-analysis of insomnia after stroke only found significant difference(MD -4.31, 95% Cl -6.19 to -2.42, $p$<0.00001). In general, all of the studies showed low methodological quality(Jadad score: mean 2.1). Risk of bias by Cochrane Handbook procedure varied. Conclusions : The results of this study could not suggest conclusive evidence that acupuncture is more effective than sham acupuncture in several diseases. In the future, more studies with rigorous acupuncture trials using sham controls should be conducted.

• Clean Technology
• /
• v.26 no.3
• /
• pp.204-210
• /
• 2020

In this study, the ignition characteristics of bio jet fuel (Bio-7629, Bio-5172) produced by F-T process and petroleum-based jet fuel (Jet A-1) were compared and analyzed. The ignition delay time of each fuel was measured by means of a combustion research unit (CRU) and the results were explained through an analysis of the properties and composition of the fuel. The ignition delay time of Bio-5172 was the shortest while that of Jet A-1 was the longest because Jet A-1 had the highest surface tension and Bio-5172 had the lowest viscosity in terms of fuel properties that could affect the physical ignition delay time. As a result of the analysis of the constituents' type and ratio, 22.8% aromatic compounds in Jet A-1 could generate benzyl radical, which had low reactivity during the oxidation reaction, affecting the increase of ignition delay time. Both Bio-7629 and Bio-5172 were composed of paraffin only, with the ratio of n-/iso- being 0.06 and 0.80, respectively. The lower the degree of branching is in paraffin, the faster the isomerization of peroxy radical is produced during oxidation, which could determine the propagation rate of the ignition. Therefore, Bio-5172, composed of more n-paraffin, possesses shorter ignition delay time compared with Bio-7629.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.54 no.1
• /
• pp.1-11
• /
• 2018

This study was conducted in order to improve fishing gear for existent net of the anchovy boat seine. Field experiments were performed to observe geometry of nets by catcher boats. When the distances between the two ships were 100, 300, and 500 m, and the speeds of towing nets were 0.6, 0.9, and 1.2 k't, respectively. The vertical opening and actual opening of each part of the existent net was as follows: the middle part of the wing net, 12.9-26.6 m, 19-39%; the entrance of the inside wing net, 23.3-35.3 m, 40-60%; the square and bosom, 18.4-24.2 m, 37-49%; the entrance of the bag net, 19.0-23.3 m, 79-96%; the flapper, 13.2-15.3 m, 142-161%; and the end of the bag net, 13.2-15.7 m, 51-61%. The actual net opening of each part of the existent nets used in this study was lower than that of the design net height, due to the low net height of the wing net and the inside wing net, it limited a range of the net height of the square and bosom. The opening of the entrance of the bag net caused the net pocket shape and inflated some parts of the nets. The tension of towing nets was measured between 4.4 and 11.0 tons, and it is necessary to reduce the structure and improve the structure of the bag net.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.2
• /
• pp.47-54
• /
• 1990

In this study, the effects of gas ratio($N_2:H_2$) and treatment time on the fatigue fracture behavior, fatigue crack growth behavior and corrosion fatigue fracture behavior for the ion-nitrided SM45C steel were investigated. The results show that the fatigue limit and corrosion fatigue strength increased in porportion to $N_2$ gas and treatment time for all kinds of specimen, used in the experiment. Compare to the non-nitrided specimen, the fatigue limit and the corrosion fatigue strength increased about $24{\sim}29%$ at $10^7$ cycles in air and $32{\sim}48%$ at $10^6$ cycles in 3% NaCl aqueous solution, respectively. Similar results were derived with SM45C steel under Compression-Tension $24{\sim}29%$ at $10^6$ cycles in air and $32{\sim}48%$ either in 3% NaCl aqueous solution or in tap water, respectively. Ion-nitrided SM45C steel showed a slow fatigue crack growth rate at relatively low range of ${\Delta}K$ compared to the non-nitrided specimen. To the contrary, its rate increase at higher range of ${\Delta}K$.

• Journal of the Korean GEO-environmental Society
• /
• v.5 no.4
• /
• pp.13-24
• /
• 2004

This study was carried out to plan the prevention of the generation and discharge of Acid Rock Drainage (ARD). The Acid Base Accounting(ABA) test was performed for geological materials such as pit wall, waste rock and stream sediments near the Imgi abandoned pyrophyllite mine in Busan, Korea. In addition, hydraulic characteristics were tested with the disk tension infiltrometer around the waste rock dump. Maximum Potential Acidity(MPA) of geological materials near the Imgi mine was 246.942kg $H_2SO_4/t$, and maximum Acid Neutralising Capacity(ANC) was 8.7kg $H_2SO_4/t$. These results indicate the pit wall and waste rock, except most of stream sediments are acid generating geological materials. These have salt and free hydrogen ion which resulted from oxidation of sulfides. Hence they could be convert rain water to acid rock drainage. Although the waste rock dump of the Imgi mine have very low infiltration rate, slopes of the waste rock dump have many "V" type erosion gullies and multi-layers. These gullies and multi-layers have coarse clastic particle layers which have very large hydraulic conductivity. Through this coarse clastic particle layer a large part of rain flow into ground. And also this layer could function as aeration path which induced oxidation of sulfide minerals and generation of ARD continuously.

• Economic and Environmental Geology
• /
• v.3 no.2
• /
• pp.55-73
• /
• 1970

The district investigated covers the central and southern portions of the Uiryong Quadrangle amounting to $40km^2$ in area and is bounded approximately by geographical coordinates of $128^{\circ}$ 28' $40^{{\prime}{\prime}}{\sim}128^{\circ}$ 24' 25"E in longitude and $35^{\circ}10{\prime}{\sim}35^{\circ}14^{\prime}06^{{\prime}{\prime}}N$ in latitude. The purpose of this investigation was to provide basic information in drawing up a comprehensive development plan of the copper ore deposits known to exist in the HamanKumbuk district with special emphasis given to the ascertainment of geological and paragenetic characteristics. The area consists chiefly of shale, sandy shale and chert, all belong to Kyongsang System of Cretaceous age. Intruded into these rocks are andesite, granodiorite, basic dikes, and acidic dikes. The mineralization which took place in the area, consists of mostly fissure-filling vein deposits, numbering several tens, with varying magnitudes. The fissures and shear zones created in rocks, such as chert and granodiorite, hosted the deposition of mineralizing vapors and/or hydrothermal solutions along their openings. The strike lengths of these veins vary from 50 to 600 meters in extension and 0.1 to 3 meters in width. Although the degree of fluctuation in width is great, it averages 0.3m. The stuctural patterns, which apparently affected the deposition of veins, are fissure patterns, trend NS to $N30^{\circ}W$, and steep-pitching tension fractures as well as normal fault pattern. Ore minerals associated with vein matters are primarily chalcopyrite and small amounts of scheelite, cobaltiferous arsenopyrite, and gold and silver intimately associated with sulphide minerals. Associated with these ore mineral are pyrite, pyrrhotite, magnetite, specularite and arsenopyrite. Gangue minerals noted are quartz, calcite, chlorite, tourmaline and hornblende. In terms of the compositions of associated minerals, the vein deposits in the district could be grouped under the following four categories: 1. Pyrrhoitite, Arsenopyrite, Gold and Silver Bearing Copper Vein (Type I) 2. Calcite-Scheelite-Copper Vein (Type II) 3. Magnetite-Pyrite-Copper Vein (Type III) 4. Tourmaline Copper Vein (Type IV) Of the four types, the first and the fourth are presently yielding relatively higher grades: of copper ores and concentrates. The estimated ore reserves total some 222,000 metric tons with the following breakdown in terms of metal contents: Name of Mines Au(g/t) Ag(g/t) Cu(%) Reserves(M/T) Kunbuk 15.92 78.69 6,074 60.498 Cheil Kunbuk - - 1.040 60,847 Haman - - 2.688 101,204 222,549 As rehabilitation of old workings and/or exploration of veins at depth proceed, additional estimation of ore reserves may become apparent and necessary. With regard to the problem of beneficiation and upgrading of low-grade ores in the district, it would be advisable to make decisions on location, treating capacity and mill flowsheet after sufficient amount of exploration is completed as suggested in the report.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.2
• /
• pp.83-93
• /
• 1988

Recent Experimental results show that the J integral can be effectively used to obtain a valid parameter for predicting plane strain and plane stress fracture. However, only a few research results have been reported for the effect of thickness where the plane strain state can not be assumed. A purpose of this study is to find the behavior of fracture touhness and tearing modulus varing the specimen thickness. The type of specimen in the present study is compact tension (CT). The thicknesses of the low carbon steel specimens that are used in the experiments are 5, 10, 15, 20 and 25mm. The measurement of crack length is taken by optical measurements method. From the study, the followings are found; 1) The fracture toughness and the tearing modulus which are obtained by using Yoon's and Simpson's formula show more conservative than that by using Rice's and Merkel's. 2) The fracture toughness is increase in specimen thickness which is reached 15mm. Beyond this thickness the fracture toughness is decreased in specimen thickness. 3) In the case of CT specimen with the thickness ranging from 5 to 25mm, the tearing modulus which is applied the same J integral equation is almost constant. 4) By using Yoon's formula, the correlation of the plane slress fracture toughness J sub(C) with specimen thickness B is expressed as the following formula. J sub(C)/J sub(IC)=1.7-15.1(B/W)+112.9(B/W) super(2) -301.3(B/W) super(3) +260.6(B/W) super(4)