• 한국재료학회지
• /
• 제24권11호
• /
• pp.585-590
• /
• 2014

Microstructural evolution in the thickness direction of an oxygen free copper processed by accumulative rollbonding (ARB) is investigated by electron back scatter diffraction (EBSD) measurement. For the ARB, two copper alloy sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked and roll-bonded by about 50% reduction rolling without lubrication at an ambient temperature. The bonded sheet is then cut to the two pieces of the same dimensions and the same procedure was repeated on the sheets up to eight cycles. The specimen after 1 cycle showed inhomogeneous microstructure in the thickness direction so that the grains near the surface were finer than those near the center. This inhomogeneity decreased with an increasing number of ARB cycles, and the grain sizes of the specimens after 3 cycles were almost identical. In addition, the aspect ratio of the grains decreased with an increasing number of ARB cycles due to the subdivision of the grains by shear deformation. The fraction of grains with high angle grain boundaries also increased with continuing process of the ARB so that it was higher than that of the low angle grain boundaries in specimens after 3 cycles. A discontinuous dynamic recrystallization occurred partially in specimens after 5 cycles.

• 한국환경농학회지
• /
• 제20권4호
• /
• pp.277-283
• /
• 2001

This paper presents treatment efficiency and plant growth of a surface-flow constructed wetland system (30 meter in length and 10 meter in width) over one year after its establishment on a floodplain of a stream. Cattails (Typha angustiflora) grown on pots were transplanted on one half of its area from inlets and reeds (Phragmites australis) on another half from an outlet. Effluent discharged from a secondary-level treatment plant was funneled into the system. The stems of cattails and reeds emerging in April 2001 grew up to 165.9 cm and 95.3 cm, respectively until July 2001. The number of stems of cattails arid reeds in July 2001 increased by 65% and 100%, respectively, compared with that just after their planting. The growth of cattails was better than that of reeds during study period. The removal rates for SS, $BOD_5$, T-N and T-P was 33%, 43%, 31%, and 51%, respectively. The system was inundated seven times by storms over the monitoring period, which disturbed its environment and led to its lower treatment rates. The increase of SS concentration in effluent after inundation of the system was attributed to the falls of soil particles onto its water surface, which had been attached to the emergent plants by floods. Purification rates for T-N were relatively low for the period of late fall through winter until early spring due to lower water temperature which may have retarded microbial nitrification and denitrification mechanisms. Reduction in T-P concentration during fall and winter was relatively higher than that during summer and spring, which may have resulted from no system perturbations by floods and heavy storms during fall and winter.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.13-16
• /
• 2008

Solid oxide fuel cell(SOFC) is an electrochemical energy conversion system with high efficiency and low-emission of pollution. In order to reduce the operating temperature of SOFC system under $800^{\circ}C$, the thickness reduction of YSZ electrolyte to be as thin as possible, e.g., less than 10 ${\mu}m$ are considered with the microstructure control and optimum design of unit cell. Methods for reducing the thickness of YSZ electrolyte have been investigated in coin cell. Moreover, a large unit cell($8cm{\times}8cm$) for SOFC was fabricated using an anode-supported electrolyte assembly with a thinner electrolyte layer, which was prepared by a tape casting method with a co-sintering technique. we studied the design factors such as active layer, electrolyte thickness, cathode composition, etc,. by the coin type of unit cell ahead of the fabrication process of a large unit cell and also reviewed about the evaluation technique of a large size unit cell such as interconnect design, sealing materials and current collector and so forth. Electrochemical evaluations of the unit cells, including measurements such as power density and impedance, were performed and analyzed. Maximum power density and polarization impedance of coin cell were 0.34W/$cm^2$ and $0.45{\Omega}cm^2$ at $800^{\circ}C$, respectively. However, Maxium power density of a large unit cell($5cm{\times}5cm$) decreased to 0.21W/$cm^2$ at $800^{\circ}C$ due to the increase of ohmic resistance. However, It was found that the potential value of a large unit cell loaded by 0.22A/$cm^2$ showed 0.76V at 100hrs without the degradation of unit cell.

• 펄프종이기술
• /
• 제48권3호
• /
• pp.51-56
• /
• 2016

The most widely used glue in a corrugator is starch, which is a natural polymer. This material needs thermal energy to achieve a binding force, so a heating section is installed in a corrugator. However, this heating section can cause quality problems in linerboards and corrugating medium and increase the production cost because of the high cost of fossil resources. Therefore, a new adhesive that provides the binding force at lower temperatures than the conventional one must be developed. In this study, SB-latex was selected as a co-adhesive and added to the starch solution. The addition of the SB-latex was determined based on the viscosity of the new adhesive. The adhesive strength and the drying energy reduction of a corrugated board were measured to evaluate the functionalities of the new adhesive. The addition of SB-latex was determined to be under 20% of the oven-dried starch based on the viscosity of the new adhesive. The adhesive strength was improved and the drying energy was reduced by applying the new adhesive.

• 한국주조공학회지
• /
• 제31권2호
• /
• pp.66-70
• /
• 2011

Hot dip aluminizing (HDA) is widely used in industry for improving corrosion resistance of material. The formation of intermetallic compound layers during the contact between dissimilar materials at high temperature is common phenomenon. Generally, intermetallic compound layers of $Fe_2Al_5$ and $FeAl_3$ are formed at the Al alloy and Fe substrate interface. In case of cast iron, high contact angle of graphite existed in the matrix inhibits the formation of intermetallic compound layer, which carry with it the disadvantage of a reduced reaction area and mechanical properties. In present work, the process for the removal of graphite existed on the surface of specimen has been investigated. And also HDA was proceeded at $800^{\circ}C$ for 3 minutes in aluminum alloy melt. The efficiency of graphite removal was increased with the reduction of particle size in sanding process. Graphite appears to be present both in the region of melting followed by re-solidification and in the intermetallic compound layer, which could be attributed to the fact that the surface of cast iron is melted down by the formation of low melting point phase with the diffusion of Al and Si to the cast iron. Intermetallic compound layer consisted of $Fe(Al,Si)_3$ and $Fe_2Al_5Si$, the layer formed at cast iron side contained lower amount of Si.

• 한국진공학회지
• /
• 제7권3호
• /
• pp.167-272
• /
• 1998

ECR plasma CVD를 이용한 SiOF박막은 낮은 유전상수를 가지고 있으며, 기존의 공정과의 정합성이 우수해 다층배선 공정에 채용이 유망한 재료이지만 수분의 흡수로 인한 유전율의 상승과 후속공정의 안정성이 문제점으로 부각되고 있다. 따라서 본 연구에서는 SiOF박막의 내흡습성과 후속공정에서의 안정성을 향상시키기 위하여 SiOF박막을 증착한 후 후속 산소 플라즈마 처리를 행하였다. SiOF박막은 산소 플라즈마 처리를 수행함으로써 SiOF박막의 밀도가 증가하고, 수분과의 친화력이 강한 Si-F 결합이 감소하는 것이 주요한 원인으로 사료된다. 하지만 플라즈마 처리 시간이 5분 이상으로 증가하면 유전율의 증가가 일어난다. 따라서 본 실험에서는 산소 플라즈마 처리조건이 마이크로파 전력이 700W, 공정 압력이 3mTorr, 기판온도가 $300^{\circ}C$일 경우 플라즈마 처리시간은 3분이 적당한 것으로 생각 된다.

• 보존과학회지
• /
• 제18권
• /
• pp.33-50
• /
• 2006

영산강유역이라는 지역적 연계성을 가진 영광 군동, 무안 인평고분군, 무안 구산리고분군, 함평 국산유적에서 출토된 유물 중 백제식 묘제인 횡혈식석실분 출현 이전으로 편년되는 철기유물 6점을 선정하여 미세조직을 분석하였다. 분석 결과, 고대 영산강유역에서는 저온환원법에 의해 괴련철을 생산하는 기술이 주를 이루고 있었으며, 아울러 탄소를 제거시켜 강소재를 생산하는 기술체계가 이루어졌을 가능성도 확인되었다. 또한 강도를 필요로 하는 부위에만 담금질을 함으로써 높은 강도를 가짐과 동시에 담금질 조직이 가지는 취성을 담금질이 안된 부위에 분산시켜 철기가 깨지는 것을 방지하고 인성을 부여하는 기술이 이루어지고 있었다고 생각된다. 이러한 기술은 2세기대로 편년되는 영광 군동 출토 철부 미세구조에서 확인되고 있어 높은 기술체계를 가진 집단이 2세기 이전에 존재하고 있었고 5세기 말까지 이어졌을 가능성이 높다고 판단된다. 낮은 탄소함량의 괴련철로 철기를 제작하는 경우 성형-침탄-열처리-단타를 반복적으로 행하는 제작 공정이 이루어진 것으로 보인다.

• Journal of Microbiology and Biotechnology
• /
• 제28권4호
• /
• pp.534-541
• /
• 2018

Kimchi (a traditional Korean fermented vegetable) was prepared with a starter, Lactobacillus zymae GU240 producing ${\gamma}$-aminobutyric acid (GABA), and one precursor of GABA (glutamic acid, glutamic acid monosodium salt (MSG), or kelp extract). L. zymae GU240, an isolate from kimchi, can grow at 7% NaCl and low temperature. Five different kimchi samples were fermented for 20 weeks at $-1^{\circ}C$. Kimchi with starter alone could not produce GABA. The GABA content was highest in kimchi with co-inoculation of the starter and MSG (1% (w/w)). Kimchi co-inoculated with the starter and kelp extract powder (3% (w/w)) had the second highest GABA content. Addition of glutamic acid powder (1% (w/w)) caused a reduction in the pH level of kimchi and growth inhibition of lactic acid bacteria and yeasts. Kimchi samples with MSG or kelp extract showed improvement of sensory evaluation scores. The results demonstrate the possibility to produce kimchi with improved functionality and taste by using L. zymae GU240 as a starter along with a suitable precursor such as MSG or kelp extract.

• 한국응용과학기술학회지
• /
• 제28권4호
• /
• pp.472-481
• /
• 2011

It is known that the content of saturated fatty acids methyl ester (SFAME) affect the pour point of biodiesel at low temperature. In this study, biodiesel (BD) was produced from beef tallow (TAL) by alkali catalyst. To reduce the saturation in BD, acetone fractionation was applied. Besides, TAL was also solvent-fractionated to reduce the saturated fatty acid (SFA) content for further producing BD. With acetone, TAL or TAL methyl ester (5:1 v/w) were fractionated at 10, 0, -10, and $-15^{\circ}C$, respectively. At $-10^{\circ}C$, 17.35% of SFA was observed in fractionated TAL (liquid part, -10TAL) when 5:1 solvent ratio was used for 24 hr. Under the same condition, fractionated BD (liquid part, -10BD) showed SFA (33.14%) with 78wt % yield. Also, fractionation of BD with different concentration of crystallizer 209 (0.1, 0.5, and 1%) along with different time (2, 6, 12, and 24 hr.) was observed. The best condition for reducing the SFA was 0.5% of crystallizer 209 addition for 12 hr of fractionation time at $-10^{\circ}C$, in which 30.14% of SFA content was observed in BD (liquid part). Among different crystallizer, ps 66 showed the least content of SFA content (23.28%) in BD after fractionation ($-10^{\circ}C$ and 24 hr) with 0.5wt% addition.

• Korean Chemical Engineering Research
• /
• 제48권3호
• /
• pp.355-358
• /
• 2010

유도 결합 저온 플라즈마를 사용하여 폴리카보네이트 시료를 처리한 후 표면 특성 변화를 분석하였다. 표면 거칠기는 플라즈마 공정조건에 상관없이 표면 처리 후에 모두 증가하였으나, 산소 분위기에서 플라즈마 처리했을 때 가장 크게 증가하였다. 표면의 화학 결합 분석에서 플라즈마 처리 전 시료의 산소 함량이 산소 플라즈마 처리 후에 43% 증가하여 표면에 친수성 극성기의 형성이 촉진되었다. 공정 변수 중, 처리 시간에 따른 접촉각 변화는 산소 분위기에서 가장 낮은 접촉각 $9.17^{\circ}$을 얻을 수 있었고, 방전 전력의 증가는 같은 처리 시간에서 빠르게 접촉각의 감소를 보여 플라즈마 표면처리 시간을 단축시키는 효과를 주었다. 그러나 방전기체 유량의 증가에 대한 접촉각 변화에 대한 영향성이 크지 않았다.