• 한국식품과학회지
• /
• 제21권3호
• /
• pp.331-337
• /
• 1989

항균력을 지닌다고 보고된 겨자유는 김치의 주요 유산균인 락토바실루스 플란타룸(Lactobacillus plantarum), 락토바실루스 브레비스(Lactobacillus brevis), 페디오코커스 세레비지에 (Pediococcus cerevisiae), 로이코너스톡 메세테로이데스(Leuconostoc mesenteroides)에 항균력을 지니고 있었으며, 김치제조시 겨자유 및 겨자분을 첨가하였을 때 적숙기에 이르는 시간이 지연되었다. 겨자유의 매운맛은 배추, 무우의 매운맛 성분과 잘 조화되어 풍미에 좋은 영향을 줄 뿐 아니라 신맛을 약화시키는 효과도 지니고 있었다. 저온 열처리+겨자+과산화수소 처리 병용은 숙성이 완만하게 진행되어서 대조군에 비해 김치 적숙기에 이르는 시간이 2.5배 정도 연장되었다. 저온 열처리+겨자+과산화수소+후처리 병용군은 $15^{\circ}C$에서 저장하는 동안 발효가 천천히 진행되어 저장 15일 후에도 pH 4.32, 산도 0.4%로서 숙성 초기단계에 머물러 있었으며 대조군에 비해 김치적숙기에 이르는 시간이 5배 정도 연장되었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.229-234
• /
• 2006

The oxy-fuel combustion heating characteristics is investigated experimentally by measuring furnace and steel temperature variations for batch type furnace simulator with a specially designed low NOx oxy-fuel burner. Economics of using oxy-fuel combustion is confirmed and, the furnace and steel temperature variations for different heating conditions are compared to deduce optimal heating control pattern for energy savings and rapid uniform heating. High $CO_2$ concentration (> 80-90%), low NOx (< 40ppm) and CO (< 10ppm) are measured in the flue gas. Temperature differences (< $30^{circ}C$) inside the furnace and steel are reduced relatively by increasing the burner jet momentum.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.253-254
• /
• 2007

In this study, in order to develop low temperature sintering multilayer piezoelectric actuator, PMN-PNN-PZT system ceramics were fabricated using $Li_2CO_3-Bi_2O_3$-CuO as sintering aids and their piezoelectric and dielectric characteristics were investigated as a function of heating rate. At sintering temperature of $900^{\circ}C$, with increasing heating rate, electromechanical coupling factor(kp), mechanical quality factor(Qm) and dielectric constant $({\varepsilon}_r)$ were increased.

• 한국태양에너지학회 논문집
• /
• 제33권2호
• /
• pp.70-77
• /
• 2013

Recently the radiant panel heating and cooling system has been regarded as an alternative of low temperature heating and high temperature cooling by applying the renewable energy sources to the heating and cooling of buildings. Especially this system can be used as HVAC system alternatives in super high-rise buildings for energy saving and thermal comfort. Also it can be possible to reduce the plenum space because the minimum ventilation air will be supplied into the space. This study focused on the evaluation the basic characteristics of thermal output in prefabricated steel wall panel system for radiant heating and cooling. In order to evaluate the thermal output according to both various supply water temperatures and supply water flow rates, three-dimensional dynamic heat transfer analysis was performed. As results, for the heating mode, thermal output increased by 26% with the supply temperature increasing by $5^{\circ}C$. The surface temperature of panels range within $1{\sim}3^{\circ}C$. For the cooling mode, thermal output decreased by 18.2% with the supply temperature increasing by $2^{\circ}C$. The surface temperature of panels range within $0.5{\sim}1^{\circ}C$ and it was shown the even temperature distribution.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.173-181
• /
• 1994

A Cold spot temperature control system for the batch annealing furnace has been estabilished in order to reduce energy consumption to improve productivity and stabilize the propertics of products. Therefore we confirmed a relation between annealing cycle time and atmospheric gas, variation of coil cold spot temperature with time during heating and actual temperature measurements at mid-width of each coil during heating and actual temperature measurements at mid-width of each coil during soaking. The results of the tempaeature variation effect on the batch annealing are as follows. 1) Heating time is reduced to one half with increasing atmospheric gas flow rate and changing of atmospheric gas component from HNx to Ax gas, and annealing cycle time is reduced to 2.7 times. 2) In case of short time healing, the slowest heating part is the center of B coil, in case of long time heating, the low temperature point moves from the center of coil to inside coil. And the temperature in this part is higher than other parts when cooling. When finished heating, the cold spot is located 1/3 of coil inside in case of HNx atmospheric gas. But center of coil in case of Ax atmospheric gas. 3) The outside of top coil is the highest temperature point when heating, which becomes the lowest temperature point when cooling. So, this point becomes high temperature zone at heating and low temperature zone at cooling, It has relation according to atmospheric gas component and flow rate. 4) Soaking time at batch annealing cycle determination is made a decision by the input coil width, and soaking time for quality homogenization of 1214mm width coil must be 2.5 hours longer than that of 914mm width coil for the same ciol weight. 5) Annealing cycle time with Ax atmospheric gas is extended 1 hour in of slow cooling during 5 hours in order to avoid rapid cooling.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권4호
• /
• pp.132-139
• /
• 2017

본 연구에서는 저온환경에서 콘크리트 동해를 방지하기 위해 생석회의 화학반응을 활용한 발열시트 및 단열재를 사용하여 제작한 거푸집 특성을 실험을 통해 평가하였다. $-10^{\circ}C$ 정온조건에서 거푸집 실험 결과, 발열시트가 부착된 거푸집의 경우 발열시트 내부 생석회의 발열로 인해 타설 초기에 일반거푸집에 비해 $10^{\circ}C$이상 높은 온도이력을 보여주었고 단열재를 부착한 거푸집의 경우 콘크리트 수화열을 보존하여 지속적으로 높은 온도를 유지하는 특징을 나타냈다. 아이소핑크와 발열시트를 부착한 거푸집과 진공단열재를 붙인 거푸집이 압축강도나 적산온도에서 가장 높은 값을 가졌다. 압축강도 측정시 진공단열재 및 아이소핑크와 발열시트를 부착한 거푸집이 재령 3일에서 약 5 MPa로 가장 높게 측정되었다. 몽골 현지 외기온도에서도 실험을 하였는데 앞선 결과와 마찬가지로 발열시트, 단열재를 함께 붙인 거푸집이 48시간 동안 $25^{\circ}C$ 이상으로 가장 높은 온도이력를 나타내었다. 따라서 거푸집에 발열시트 및 단열재 부착을 함으로써 발열 및 단열효과로 인해 저온환경에서 콘크리트 강도발현에 도움을 주는 것을 확인할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.111-114
• /
• 2011

Waterprooping Method with sheet need to study technology and multilateral verification considering the arctic conditions as low temperature and humidity, which is the result only considered of material aspects without environmental condition in construction But there are no measures up until now. To solve this problem by using high frequency induction heating method developed waterproof sheets, cold (5 ℃ or less) can be applied in a more stable environment, water-resistant materials and construction methods were studied for development. The results of the test showed that high frequency induction heating method is effective for usability in low temperature condition and securement of proper quality than existing Waterprooping Method with sheet need.

• Elastomers and Composites
• /
• 제51권4호
• /
• pp.280-285
• /
• 2016

The purpose of this study is to get optimum design and operation conditions of the heating rubber roller for laminating process. The cause of performance degradation of heating rubber roller is delamination of rubber on metal tube, rubber aging due to high temperature. We measured the material properties of thermal expansion, thermal conductivity, specific heat and density and analyzed thermal distributions of rubber layer using finite element method. As a result of heat/flow analysis, the density distribution of heating coil must shorten the stabilization time by reducing the temperature deviation on the length direction at the temperature rising section after increasing the density of the area contacting with the laminate film at the center part which is an opposite of the current composition while enabling to maintain the temperature of heater to be consistent while maintaining the temperature deviation to be low when heat loss is created. Finally, we determined optimum heating method of heating rubber roller.

• Journal of Biosystems Engineering
• /
• 제32권2호
• /
• pp.102-108
• /
• 2007

Heat pump systems are recognized to be heating and cooing systems. In this study, to check the practical application possibility of heat pump systems as low temperature storage systems and get basic data, apples of a long term storage items were stored and performance of low temperature storage and quality changes of apples were evaluated. Cooling coefficient of performance of the system was from 1.1 to 1.3. Although ambient air temperature varied widely from $-13^{\circ}C$ to $29.6^{\circ}C$ during low temperature storage period from January to June, the average temperature of low temperature storage chamber was $1.1^{\circ}C$ at setting temperature of $1.5^{\circ}C$. Sucrose of apples stored by the heat pump decreased from initial sucrose of 15.4% (Brix number) to final sucrose of 14.3%. Weight loss ratio of apples was 9.7% and internal and external view of apples after low temperature storage were very satisfactory with the naked eye.

• 한국태양에너지학회 논문집
• /
• 제27권3호
• /
• pp.79-85
• /
• 2007

This paper addresses the indoor air quality when radiant floor heating is applied in large space. Radiant heat exchange between surfaces depends on the orientation and the temperature of the surfaces. Also, the temperature and the radiant characteristic of the wall and the roof that face the floor have great influence on the indoor air environment due to the largeness of the wall and the roof in large spaces. In this study, we simulate a test-cell(25X20X10) using a ies YE And using a CFD(microflo in VE), an indoor air environment was investigated to establish the optimum temperature of floor. At the first time of the heating, high floor temperature is demanded. At the middle of the heating, however, the temperature of the residential space was formed appropriately, although the temperature of the floor was set low.