• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.82-85
• /
• 2000

We introduce pulsed $CO_2$ laser power supply excited by half-wave rectified 60Hz AC discharge some advantage of cost and size compared to a typical pulsed power supply. AC frequency is adjusted from 10Hz to 60Hz to control laser output. In this laser, a low voltage open loop control for high voltage AC discharge circuits is employed to avoid the HV sampling or switching. The control is achieved by using a ZCS circuit and a PIC one-chip microprocessor that control the gate signal of SCR precisely. The pulse repetition rate is limited by 60Hz due to a high leakage inductance. The maximum laser output was obtained about 20W at the condition of total pressure, 18Torr and pulse repetition rate,60Hz.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.8 s.239
• /
• pp.956-962
• /
• 2005

A three-dimensional computation was conducted to make a study about effects of the inlet boundary layer thickness on the total pressure loss in a low-speed axial compressor operating at the design condition ($\phi=85\%$) and near stall condition($\phi=65\%$). Differences of the tip leakage flow and hub corner-stall induced by the inlet boundary layer thickness enable the loss distribution of total pressure along the span to be altered. At design condition, total pressure losses for two different inlet boundary layers are almost alike in the core flow region but the larger loss is generated at both hub and tip when the inlet boundary layer is thin. At the near stall condition, however, total pressure loss fer the thick inlet boundary layer is found to be greater than that for the thin inlet boundary layer on most of the span except the region near hub and casing. Total pressure loss is scrutinized through three major loss categories in a subsonic axial compressor such as profile loss, tip leakage loss and endwall loss using Denton's loss model, and effects of the inlet boundary layer thickness on the loss structure are analyzed in detail.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.1 s.256
• /
• pp.68-75
• /
• 2007

A three-dimensional computation is conducted to simulate a three-dimensional rotating stall in a low speed axial compressor. It is generally known that a tip leakage flow has an important role on a stall inception. However, almost of researchers have taken no interest in a role of the hub-comer-stall on the rotating stall even though it is a common feature of the flow in an axial compressor operating near stall and it has a large effect on the flows and loss characteristics. Using a time-accurate unsteady simulation, it is found that the hub-comer-stall may be a trigger to collapse the axisymmetric flows under high loads. An asymmetric disturbance is initially originated in the hub-comer-stall because separations are naturally unstable flow phenomena. Then this disturbance is transferred to the tip leakage flows from the hub-comer-stall and grows to be stationary stall cells, which adheres to blade passage and rotate at the same speed as the rotor. When stationary stall cells reach a critical size, these cells then move along the blade row and become a short-length-scale rotating stall. The rotational speed of stall cells quickly comes down to 79 percent of rotor so they rotate in the opposite direction to the rotor blades in the rotating frame.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.4
• /
• pp.349-356
• /
• 2007

The present study investigated local heat/mass transfer characteristics on the tip of the rotating turbine blade with various incoming flow incidence angles. The experiments are conducted in a low speed annular cascade with a single stage turbine. The blade has a flat tip with a mean tip clearance of 2.5% of the blade chord. The incoming flow Reynolds number is $1.5{\times}10^5$ at design condition. To examine the effect of off-design condition, the experiments with various incidence angles ranging between $-15^{\circ}$ and $+7{\circ}$ were conducted. A naphthalene sublimation method is used to measure detailed mass transfer coefficient on the blade. The results indicated that the incidence angle strongly affects the behavior of tip leakage flow around the blade tip and consequently plays an important role in determining heat transfer characteristics on the tip. For negative incidence angles, the heat/mass transfer in the upstream region on the tip decreases by up to 20%. On the contrary, for positive incidence angles, much higher heat transfer coefficients are observed even with small increase of incidence angle.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.215-223
• /
• 2009

A design methodology for transformers including integrated and center-tapped structures for LLC resonant converters is proposed. In the LLC resonant converter, the resonant inductor in the primary side can be merged in the transformer as a leakage inductance. And, the absence of the secondary filter inductor creates low voltage stress on the secondary rectifiers and is cost-effective. A center-tapped structure of the transformer secondary side is widely used in commercial applications because of its higher efficiency and lower cost than full-bridge structures in the rectifying stages. However, this transformer structure has problems of resonance imbalance and transformer inefficiency caused by leakage inductance imbalance in the secondary side and the position of the air-gap in the transformer, respectively. In this paper, gain curves and soft-switching conditions are derived by first harmonic approximation (FHA) and operating circuit simulation. In addition, the effects of the transformer including integrated and center-tapped structures are analyzed by new FHA models and simulations to obtain an optimal design. Finally, the effects of the air-gap position are analyzed by an electromagnetic field simulator. The proposed analysis and design are verified by experimental results with a 385W LLC resonant converter.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.436-446
• /
• 2016

A novel step-up DC-DC converter with a switched-coupled-inductor-capacitor (SCIC) which successfully integrates three-winding coupled inductors and switched-capacitor techniques is proposed in this paper. The primary side of the coupled inductors for the SCIC is charged by the input source, and the capacitors are charged in parallel and discharged in series by the secondary windings of the coupled inductor to achieve a high step-up voltage gain with an appropriate duty ratio. In addition, the passive lossless clamped circuits recycle the leakage energy and reduce the voltage stress on the main switch effectively, and the reverse-recovery problem of the diodes is alleviated by the leakage inductor. Thus, the efficiency can be improved. The operating principle and steady-state analyses of the converter are discussed in detail. Finally, a prototype circuit at a 50 kHz switching frequency with a 20-V input voltage, a 200-V output voltage, and a 200-W output power is built in the laboratory to verify the performance of the proposed converter.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.407-410
• /
• 2002

As a part of electro-mechanical totally implantable artificial heart, a transcutaneous energy transmission system has been developed. By mutual magnetic induction between the first coil on the skin and the subcutaneously implanted second coil, the system transfers electrical power through the skin. This research aimed a minimizing the size of the implanted part as well as maximizing the transfer efficiency. When an air gap is 1$\sim$2cm, voltage gain and current gain low and it is hard to transfer energy due to large leakage flux. That is, the required input voltage and input current must be large compared with the output voltage and output current, respectively, This paper research the inverter topology and the control method in order to increase the voltage gain and the current gain. For this purpose, this inverter employs double tune to compensate the large leakage inductance of primary and secondary of the transcutaneous transformer. And the output energy of transcutaneous energy transmission system supply for Lithium-ion battery charger.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.12
• /
• pp.1016-1022
• /
• 2001

This study presents the microstructure-electrical property relationship of reactive-sputtered Ta$_2$O$_{5}$ MIM capacitor structure processed by annealing in a vacuum and $O_2$ ambience. A microstructural investigation showed the existence of amorphous phase in as-deposited condition and the formation of preferentially oriented-Ta$_2$O$_{5}$ in $700^{\circ}C$ annealing. On annealing under the $O_2$ atmosphere, the Ta$_2$O$_{5}$ film exhibited the trend of its composition\`s approaching to stoichiometry from off-stoichiometry, analyzed by EPMA, the leakage current decrease and the enhanced temperature-capacitance characteristic stability. In the case of low temperature vacuum-annealing treatment, the leakage current behavior was stable irrespective of applied electric field. In the high temperature-annealed film at a vacuum condition, the electrical properties was observed to deteriorate. The results state that in Ta$_2$O$_{5}$ film annealed at $O_2$ atmosphere, gives rise to improvement of electrical characteristics in the capacitor were improved by reducing oxygen-vacancy and dandling Ta-O bond.-O bond.

• Korean Journal of Environmental Agriculture
• /
• v.39 no.3
• /
• pp.273-279
• /
• 2020

BACKGROUND: After transplanting, the recent abnormal low temperature caused physiological disorders of pepper seedlings. This study was conducted to evaluate the effects of UV-A LED, a physical elicitor, on the chilling tolerance of pepper seedlings. METHODS AND RESULTS: Seedlings were continuously irradiated with 370 and 385 nm UV-A LEDs with 30 W·m^-2 for 6 d. After that, seedlings were exposed to 4℃ for 6 h and then recovered under the normal growing condition for 2 d. There were no significant differences in growth characteristics of UV-A treatments compared to the control. Fv/Fm values of two UV-A treatments were below 0.8. Electrolyte leakage in the control was increased by chilling stress, while 385 nm UV-A had the significantly lowest value. Total phenolic content and antioxidant capacity of two UV-A treatments significantly increased due to UV-A radiation. However, total phenolic content and antioxidant capacity of the control increased due to chilling stress and tended to decrease again during the recovery time. CONCLUSION: We confirmed that UV-A light was effective to induce the chilling tolerance of pepper seedling, and the supplemental radiation of 385 nm UV-A LED before transplanting could be used as a cultivation technique to produce high quality pepper seedlings.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.388-388
• /
• 2012

In this letter, We have investigated cell characteristics of the alloy FePt-NDs charge trapping memory capacitors with high-k $Al_2O_3$ dielectrics as a blocking oxide. The capacitance versus voltage (C-V) curves obtained from a representative MOS capacitor embedded with FePt-NDs synthesized by the post deposition annealing (PDA) treatment process exhibit the window of flat-band voltage shift, which indicates the presence of charge storages in the FePt-NDs. It is shown that NDs memory with high-k $Al_2O_3$ as a blocking oxide has performance in large memory window and low leakage current when the diameter of ND is below 2 nm. Moreover, high-k $Al_2O_3$ as a blocking oxide increases the electric field across the tunnel oxide, while reducing the electric field across the blocking layer. From this result, this device can achieve lower P/E voltage and lower leakage current. As a result, a FePt-NDs device with high-k $Al_2O_3$ as a blocking oxide obtained a~7V reduction in the programming voltages with 7.8 V memory.