• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.1-10
• /
• 2012

This paper presents an experimental result and suggests the confinement effect of headed cross tie in reinforced concrete(RC) columns subjected to cycling horizontal loads under constant axial load. Five RC columns specimens were manufactured, taking confined type of transverse reinforcement, whether or not using cross tie, end detail of cross tie (hooked or headed), and axial stress in column as major variables, Cyclic horizontal load applied to the columns under constant axial stress and the effect of cross tie to structural capacity of column was evaluated from the test. The column without cross tie failed showing bending deformation of hoop with crack in core concrete at low horizontal load while the column with cross tie showed quite improved strength and ductility by suppressing bending deformation of hoop as well as buckling of longitudinal bar at once even after crack in core concrete. At high lateral displacement, the column with hooked cross tie showed the failure pattern loosing the confining force of cross tie since the $90^{\circ}$ hooked part of cross tie was stretched out and the cracked core concrete lumps were came off. However, the column with headed cross tie showed very stable behavior since the head of cross tie effectively confined the hoop and longitudinal bars even at high lateral displacement.

• The Journal of Engineering Geology
• /
• v.22 no.4
• /
• pp.459-466
• /
• 2012

A difficulty encountered in engineering seismic mapping is that reflection events from shallow discontinuities are commonly overlapped with coherent noise such as air wave, direct waves, head waves, and high-amplitude surface waves. Here, the radial trace transform, a simple geometric re-mapping of a trace gather (x-t domain) to another trace gather (v-t domain), is applied to investigate the rejection effect of coherent linear noises. Two different types of data sets were selected as a representative database: good-quality data for intermediate sounding (hundreds of meters) in a sedimentary basin and very noisy data for shallow (${\leq}50m$) mapping of the weathered zone and bedrock surface. Results obtained with cascaded application of the radial transform and low-cut filtering proved to be as good as, or better than, those produced using f-k filtering, and were especially effective for air wave and direct wave. This simple transform enables better understanding of the characteristics of various types of noise in the RT domain, and can be generally applied to overcoming diffractions and back-scatterings caused by joints, fractures, and faults commonly that are encountered in geotechnical problems.

• The Journal of Engineering Geology
• /
• v.30 no.2
• /
• pp.147-160
• /
• 2020

Unsaturated hydraulic conductivity of near-surface unconsolidated layers depends on the physical properties and water content of the unconsolidated layers. So far, many studies have been conducted on the unsaturated hydraulic conductivity of near-surface unconsolidated layers. However, researches on hydraulic conductivity of unsaturated fractured rocks have been relatively rare. In relation to the construction of a low/intermediate level radioactive waste surface-disposal facility, this study compared and analyzed van Genuchten parameters (α, n) in the laboratory and the hydraulic conductivity obtained in field tests for fractured hornfels at a radioactive-waste disposal site of Korea. The relationship between the field hydraulic conductivity and van Genuchten parameters using data from the ten depth intervals of three boreholes resulted in that the correlation coefficient (R) between the hydraulic conductivity and the van Genuchten parameter α was 0.7607, showing positive correlation whereas the R between the hydraulic conductivity and the van Genuchten shape-defining parameter n was -0.8720, showing negative correlation. Hence, this study confirmed the relationship between the field hydraulic conductivity and the van Genuchten unsaturated functions for the unsaturated fractured hornfels.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.4
• /
• pp.746-754
• /
• 1996

The purpose of this study was to evaluate the fracture strength of porcelain laminate veneer with various lingual extention length when incisal restoring. Sixty recently extracted, intact maxillary incisors were used and stored in a physiologic saline solution from the time of extraction. Seating form was preparation at the labial surface of each tooth with a water-cooled round diamond bur. Standard block was formed with 32 gauge and 24 gauge wax at tooth labial and lingual surface. Lingual extention length differed according to each group. (group I : 0.5mm, group II : 1 mm, group III : 2mm, group IV : 0mm) All tooth specimens were impressioned with examix(GC Inc., Japan). Refractory cast were maked with refractory die material(Ceramco Inc., U.S.A.) Laminate porcelain (Ceramco II Veneer porcelain, Ceramco Inc., U.S.A.) was condensed in refractory die cast and baked according to the manufacturer's recommendations. Each surface was contoured with low speed diamond bur according to guide block. All porcelain specimens were sandblasted and ultrasonically cleaned in distlled water for 3 minutes. Then, all porcelain specimen were etched with 8% hydrofluoric acid for 5 minutes. Sixty specimens were bonded with composite resin cement(Choice Porcelain Veneer System, Bisco Inc., U.S.A.) according to manufacture's directions. The fracture loads of the specimen were measured by Instron universal testing machine. The mean values of fracture loads for the groups were statistically compared by Duncan's multiful range test. The result were as follows : Mean fracture strengths of each group were 86.95Mpa in no lingual extention group, 44.98Mpa in 0.5mm lingual extention group, 27.47Mpa in 1mm lingual extention group, 19.61Mpa in 2mm lingual extention group. There was a statistically significant difference between all group(p<0.01).

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.601-610
• /
• 2007

Statement of problem: The adhesion between titanium and ceramic is less optimal than conventional metal-ceramic bonding, due to reaction layer form on cast titanium surface during porcelain firing. Purpose: This study characterized the effect of titanium-ceramic adhesion after gold and TiN coating on cast and wrought titanium substrates. Material and method: Six groups of ASTM grade II commercially pure titanium and cast titanium specimens$(13mm{\times}13mm{\times}1mm)$ were prepared(n=8). The conventional Au-Pd-In alloy served as the control. All specimens were sandblasted with $110{\mu}m\;Al_2O_3$ particles and ultrasonically cleaned for 5min in deionized water and dried in air before porcelain firing. An ultra-low-fusing dental porcelain (Vita Titankeramik) was fused on titanium surfaces. Porcelain was debonded by a biaxial flexure test at a cross head speed of 0.25mm/min. The excellent titanium-ceramic adherence was exhibited by the presence of a dentin porcelain layer on the specimen surface after the biaxial flexure test. Area fraction of adherent porcelain (AFAP) was determined by SEM/EDS. Numerical results were statistically analyzed by one-way ANOVA and Student-Newman-Keuls test at ${\alpha}=0.05$. Results: The AFAP value of cast titanium was greatest in the group 2 with TiN coating, followed by group 1 with Au coating and the group 3 with $Al_2O_3$ sandblasting. Significant statistical difference was found between the group 1, 2 and the group 3 (p<.05). The AFAP value of wrought titanium was greatest in the group 5 with TiN coating, followed by the group 4 with Au coating and the group 6 with $Al_2O_3$ sandblasting. Conclusion: No significant difference was observed among the three groups (p>.05). The AFAP values of the cast titanium and the wrought titanium were similar. However the group treated with $Al_2O_3$ sandblasting showed significantly lower value (p<.05).

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.2
• /
• pp.368-382
• /
• 1998

The purpose of this study is to evaluate and compare the results of argon laser for 5 seconds, argon laser for 10 seconds, and visible light for 40 seconds photo-polymerization in compressive strength, microhardness, curing depth, temperature rising during polymerization, and polymerization shrinkage. Hybrid type composite resin(Z-100) and compomer(Dyract) were used to be compared. The compressive strength was measured by an Instron(1mm/min cross head speed) in 60 specimens and the microhardness of the surface was expressed by Vickers Hardness Number(VHN) in 30 specimens. The curing depth was evaluated comparing the different values of upper and lower VHN according to irradiation time and thickness for the light source polymerization in 60 specimens. The temperature rising during photopolymerization was observed by the temperature change with thermocouple sensitizer beneath 40 specimens at the argon laser for 10 seconds and visible light 40 seconds irradiation. The polymerization shinkage was evaluated by calculating the decrease of % volume by using a dilatometer in 30 specimens. The results were as follows ; 1. In the case of compressive strength, the argon laser polymerization groups were higher than visible light group in Z-100 (p<0.05). In Dyract, the argon laser 5 seconds group did not show a significant difference with the visible light 40 seconds group. The argon laser 10 seconds group showed the markedly low value when compared with other groups (p<0.05) 2. In microhardness, Z-100 was better than Dyract when comparing by VHNs (p<0.05); however, there was not a significant difference between two materials in the visible light 40 seconds group and the argon laser 10 seconds group. 3. In the study of curing depth, Z-100 showed the consistent polymerization in argon laser irradiation because there was no difference in the VHN decrease according to the thickness change. Over the thickness control, the results did not show a significant difference between visible light and argon laser group in Z-100; however, in the case of Dyract, the visible light 40 seconds group was better than the argon laser groups(p<0.05). 4. There was a significant difference between the two materials in temperature rising during polymerization (p<0.05), but not a significant difference between irradiation times, 5. There was not a significant difference between the two materials in polymerization shrink age. The argon laser 5 seconds group was smaller than the other groups (p<0.05). It could be concluded that Z-100 polymerization was recommended to use the argon laser for reduction of the irradiation time while Dyract was recommended to use the visible light polymerization.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.2
• /
• pp.37-55
• /
• 1997

최근 선진국가들에서는 전자파 장애 증후군에 관심이 집중되고 있는데, 전자파에 장기 노출 되는 인구에서 뇌암이나 유방암, 백혈병 등의 발생률이 높다는 보고(Kolmodin-Hedman 등, 1988 ; Demers등, 1991)가 있어서 전자제품의 생산업체는 물론이고 사용자에 대해서도 불안한 관심사가 되 어 있다. 전자파가 생체에 미치는 영향은 열적 효과와 비열적 효과에 의한 것으로 구분된다. Microwave는 약 300MHz에서 300GHz 사이(파장 1m에서 1mm사이)의 주파수를 가지는 전자파로서 이온의 운동이나 쌍극자분자(dipole molecule)들을 진동시키므로서 조직에 열이 발생한다. 열이 과도하게 발생하면 세포 단백질이 응고하게 되는 등 일반적으로 생각할 수 있는 고열로 인한 여러 가지 유해환경이 조직 에 조성될 수 있다. 실제로 고전압의 전자파에 노출된 안구의 수정체에 백내장 등의 병변이 발생한 것 으로 보고된 바 있다(Adey,1981). 일반적으로 전자파의 생체에 대한 작용으로는 이렇듯 조직에 흡수 되는 전자파의 에너지에 의한 열작용이 지배적인 것으로 생각되어 왔다. 그러나 초저주파역대(Extre- mely low frequency, EMF)의 변조 및 펄스파 등의 영향에 관해서도 조직의 온도상승으로는 설명할 수 없는 현상이 보고된 바 있다. 이러한 비열적 효과가 신경계에 끼치는 영향에 대해서는 혈액뇌관문 의 투과성 변화(Oscar와 Hawkins, 1977), 뇌종양 발생, 칼슘대사 이상 및 신경전달물질에 대한 영향 등이 주장(Anderson, 1993)되고 있으나 아직 그 분명한 기전이 밝혀져 있지 않은 상태이다. 또한 그 영향의 평가에 서도 일정한 기준이나 지표가 정해지지 않은 실정이다. 그러므로 신경계에 대한 대체적인 소개와 더불어 전자기파의 영향에 대한 이제까지의 보고를 종합 하고 향후 연구의 방향을 소개하고자 한다.> 이온이 공동 첨가제로 더 적합하다.u(30 .angs. )/CoFe(35 .angs. )/NiO(800 .angs. ) 구조를 갖는 spin-valve 박막은 극대 MR비 6.3%, 유효자기장감응도 약 0.5(%/Oe)를 보여 spin-valve head 재료로 적합함을 알 수 있었다.다.다.다.는 각각 148 meV .angs. $^{2}$, 103.8 meV .angs. $^{2}$와 1.77 * $10^{-6}$ erg/cm, 0.67 * $10^{-6}$ erg/cm 였다.다.자 노인들을 영주권자와 귀화 시민권자의 구분없이 하나의 집단으로 간주하고 분석해 왔던 것을 볼 때, 앞으로의 연구는 이론적으로나 방법론적으로 시민권의 유무가 주거형태에 끼치는 영향도 함께 고려해야 할 것이다.에 나타난 인도의 영향은 여성복식과 남성복식에 있어서 서로 유사점과 차이점이 보이는데, 인도의 영향이 여성복식에 있어서 그 빈도가 더 높고, 종류가 더 다양함을 볼 수 있다. 여성복식에 있어서는 12가지의 다양한 인도복식스타일이 나타났으며, 그중 가장 많이 보이는 스타일은 Indian Shirt/Blouse/Smock/ Dress이며, 그 뒤를 이어 Madras, Indian lowery등을 볼 수 있다. 남성복식애 나타난 7가지의 스타일 중에는 Madras가 가장 빈도가 높으며 그외의 스타일들은 그 빈도가 매우 낮음을 볼 수 있다. 인도의 영향의 정도 (Attribution Categories) 있어서는 여성과 남성복식 모두에 있어서 인도에서 직접 수입된(originated) item이 각각 전체의 90%와 81%를 차지하여, 인도복식의 영향은 받았으나 미국내에서 제작된(attributed and connotated) item 보다 휠씬 더 많은 수를 보였다. 인도복식스타일이 가장

• Restorative Dentistry and Endodontics
• /
• v.24 no.3
• /
• pp.465-472
• /
• 1999

The aim of this study was to determine the shear bond properties of four dentin bonding systems to internal cervical dentin, and to investigate the effect of the pretreatment for removing smear layer and position of dentin on shear bond strength of dentin bonding agents. The materials tested in this study were consisted of four commercially available dentin bonding systems[Allbond 2(AB), Clearfil Linerbond 2(CL), Optibond FL(OP), Scotchbond Multi-purpose(SB)], a restorative light-cured composite resin[Z100]J and a chelating agent[RC-prep(RC)]. Fifty-six freshly extracted human molars were used in this study. Dentin specimens were prepared by first cutting the root of the tooth 1mm below the cementoenamel junction with a diamond bur in a high speed handpiece under air-water coolant, and then removing occlusal part at pulp horn level by means of a second parallel section, The root canal areas were exposed by means of cutting the dent in specimens perpendicular to the root axis. Dentin specimens were randomly assigned to two groups(pretreated group, not-pretreated group) based on the pretreatment method of dentin surface. In pretreated group, RC was applied to dentin surface for 1minute and then rinsed with NaOCl. In not-pretreated group, dentin surface was rinsed with saline Each groups were subdevided into four groups according to dentin bonding systems. Four dentin bonding systems and a restorative resin were applied according to the directions of manufacturer. The dentin-resin specimens were embedded in a cold cure acrylic resin, and were cut with a low speed diamond saw to the dimension of $1{\times}1mm$. The cut specimens were divided into three groups according to the position of internal cervical dentin. The shear bond properties of dentin-resin specimens were measured with Universal testing machine (Zwick, 020, Germany) with the cross head speed of 0.5mm/min. From this experiment. the following results were obtained : 1. In case of shear bond strength, there was no significant difference among dentin bonding systems in not-pretreated groups, whereas in pretreated groups, the shear bond strengths of AB and of SB were statistically significantly higher than those of CL and of OP. 2. The shear bond strengths of AB and of SB in pretreated groups were significantly higher than those in not-pretreated groups. 3. The shear bond strengths of radicular layer of OP were higher than those of occlusal layer of OP in not-pretreated groups, and of AB in pretreated groups. The shear bond strengths of radicular layer of AB and of CL in not-pretreated groups were higher than those in pretreated group.

• Restorative Dentistry and Endodontics
• /
• v.22 no.2
• /
• pp.751-760
• /
• 1997

Resin-modified glass ionomers were introduced in 1988 to overcome the problems of moisture sensitivity and low early mechanical strengths of the conventional glass ionomers, and to maintain their dinical advantages. The purpose of this study was to evaluate the bi-axial fracture strength of four resinmodified glass-ionomers(Fuji II LC, Vitremer, Dyract, VariGlass), one resin composite material(Z-100), and one conventional glass-ionomer(Fuji II). Three specimens of each material and shade combination were made according to the manufacturers' instructions. Materials were condensed into metal mold with a diameter of 10mm and a thickness of 2.0mm and pressed between two glass plates. Resin-modified glass ionomers were polymerized using a Visilux II light curing unit by irradiating for 60 seconds from both sides, and conventional glass ionomer was cured chemically. After specimens were removed from the molds, surfaces were polished sequentially on wet sandpapers up to No. 600 silicone carbide paper. The specimens were thermocycled for 2,000 cycles between $5^{\circ}C$ and $55^{\circ}C$ distilled water. After thermocycling, bi-axial fracture strengths were measured using a compressive-tensile tester(Zwick 1456 Z020, Germany) with the cross head speed of 0.5mm/minute. The results were as follows: 1. Two factors of the kind and color of materials had a main effect on bi-axial fracture strength (p<0.01), and bi-axial fracture strength was influenced significantly by the kinds of materials (p<0.01). But there was no significant interaction between two variables of the kind and color of materials (p>0.05). 2. Comparing the mechanical properties of the materials, the elastic modulus of Z100 was higher than any other material, and there was no difference in the displacement at fracture among materials. The bi-axial fracture strength of Z100 was significantly higher than any other material, and that of resin-modified glass ionomers was significantly higher than that of conventional glass ionomer (p<0.05). 3. In the same material group, the color of material had little influence on the mechanical properties.

• Korean Journal of Agricultural Science
• /
• v.12 no.1
• /
• pp.55-61
• /
• 1985

This study was carried out to investigate reproductive traits and sex hormone levels by growth in Korean native goats. Serum levels of FSH, LH, prolactin, estradiol-$17{\beta}$ and progesterone were determined every 15 days from the 70 days of age to 190 days by radioimmunoassay. The age and weight at sexual maturity were 183.6 days and 14.3 kg; the length of estrous cycle and estrus period were 20.3 days and 36.7 hours, respectively. The gestation period, litter size and body weight at birth were 148.4 days, 1.4 head and 1.8 kg, respectively. The levels of serum LH were highest with 3.93 mIU/ml at 70 days of age, thereafter decreased gradually to 1.21 mIU/ml at 190 days of age. The concentrations of FSH in serum were below 1.25 mIU/ml throughout the experimental period. The levels of prolactin were lowest with 3.09ng/ml at 85 days of age and highest with 4.65 ng/ml at 175 days of age. The serum levels of estradiol-$17{\beta}$ were increased with age, thus highest with 7.95 pg/ml at 190 days of age. The serum progesterone concentrations were maintained low levels (below 1.0 ng/ml) throughout the experimental period.