• 한국도로학회논문집
• /
• 제11권1호
• /
• pp.203-215
• /
• 2009

본 연구는 포스트 텐션드 콘크리트 포장(PTCP: Post-Tensioned Concrete Pavement)의 종방향 긴장 설계 방안을 구축하기 위하여 수행되었다. 우선 종방향 긴장으로 인해 PTCP 슬래브에 발생하는 응력분포를 분석하였다. 그리고 설계에 필요한 환경하중과 차륜하중이 PTCP 슬래브에 작용할 때 슬래브에 발생하는 인장응력의 분포를 분석하였다. 또한 슬래브와 하부지반 사이의 마찰저항 및 긴장으로 인해 발생하는 여러 손실원인들을 고려하여 긴장손실량을 산정하였다. 설계에 사용될 발생 인장응력은 각각의 하중에 의해 발생 가능한 최악의 조건에 의해 산정되며 여러 손실들은 현장조건을 최대한 반영하여 산정된다. 이러한 환경 및 차륜하중 등의 설계하중과 긴장 시 발생하는 각종 손실들을 감안한 유효긴장량을 산정하였으며 긴장응력 결정의 기준이 되는 콘크리트 슬래브의 허용인장응력의 영향에 대하여 분석하였다. 궁극적으로 종방향 긴장 설계방안은 설계하중에 대한 슬래브의 응력을 산출한 후 콘크리트 슬래브의 허용인장응력을 감하여 요구되는 긴장응력을 산출하고, 각종 손실이 고려된 유효긴장량과의 비교를 통해 합리적인 긴장간격 및 긴장량을 결정하는 것이다.

• 한국도로학회논문집
• /
• 제10권4호
• /
• pp.257-267
• /
• 2008

본 연구에서는 프리스트레스트 콘크리트 포장에 횡방향으로 프리스트레싱을 가할 때 포장체에 발생하는 응력분포를 분석하여 긴장간격에 따른 특성을 파악하고 종방향과 횡방향 긴장의 상호 영향을 분석하기 위하여 유한요소 모델을 개발하여 구조해석을 수행하였다. 연구결과 횡방향 긴장간격은 작을수록 응력분배를 적절하게 할 수 있고 압축응력의 손실범위를 줄일 수 있으나 경제성 문제를 제고하여 적절한 긴장간격을 선정하여야 한다. 포장체의 노견, 주행위치, 중앙부 등의 여러 위치에서 분석한 횡방향 응력분포는 긴장간격이 넓을수록 평균응력과의 차이가 커지며 그 차이는 슬래브 중앙부로 갈수록 감소하게 된다. 횡방향 긴장을 가하면 종방향으로도 추가 긴장력 이 발생하게 되지만 그 크기는 무시 할 수 있을 정도로 작기 때문에 종횡방향 긴장 설계는 독립적으로 수행하여도 타당하다. 또한 횡방향 긴장 설계 시 이러한 긴장에 의한 응력분포를 이용하는 방안에 대해서도 본 논문에 언급하였다.

• 대한조선학회논문집
• /
• 제44권5호
• /
• pp.496-503
• /
• 2007

Although weld-induced deformation is inevitable in shipbuilding, it is important to reduce it as low as possible during fabrication for a more efficient production of ships' blocks. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates, and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. in order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. Numerical simulation has been also carried out to compare the weld-induced deformation and residual stress. From the present study, it has been found that the tensioning method is very effective on reduction of weld-induced residual stress as well as weld-induced deformation.

• Journal of Welding and Joining
• /
• 제25권6호
• /
• pp.59-63
• /
• 2007

The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates and in addition internal and external constraints have much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. In order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test has been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. From the present experimental study, it has been found that the tensioning method is very effective in reducing the weld-induced residual stress as well as the weld-induced deformation.

• 한국해양공학회지
• /
• 제20권3호
• /
• pp.103-108
• /
• 2006

It has been well appreciated that reducing weld-induced deformation as law as possible is important during fabrication for a more efficient production of blocks. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the weld-induced deformation. In order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. From the present experimental study, it has been found that the tensioning method is very effective on reduction of weld-induced residual stress as well as weld-induced deformation.

• 전기학회논문지
• /
• 제64권10호
• /
• pp.1517-1522
• /
• 2015

Since electric railroad vehicle pass through repeatedly on the railroad bridge, the dynamic load that causes the change of tension of contact wire affect it constantly. In this paper, we measured the dynamic displacement of the railroad bridges to analyze the effect of tension in the catenary. A result of dynamic measurement of the longitudinal displacement, it's maximum value was 39.9mm which was lower than the primary management criteria 378mm. Also on the based of a maximum temperature, it shows a feature that the longitudinal displacement value increased as temperature rise from April to October. In terms of behavior characteristics of a tensioning device, it was confirmed to be the value of 50mm stroke movement when the temperature changes ±5℃.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.127-128
• /
• 2009

본 연구는 프리스트레스트 콘크리트 포장(PSCP: Prestressed Concrete Pavement)의 종방향 긴장설계법을 개발하기 위하여 수행되었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.57-57
• /
• 2010

For thin panel welded structure, the various welding distortions were found due to the low resistance against welding deformation. Especially, buckling distortion induced in the thin panel welded structure produce severe problems related to cost in production stage and safety in service life. So, many researches including mechanical and thermal tensioning method for preventing the occurrence of buckling distortion in the production stage have been performed. The purpose of this study is to identify the behavior of longitudinal residual stress at the SA butt weldment with thin plate of 6mm thickness under tension load by 3 dimensional FEA. For it, mesh design for 3D FEA was constructed with 20 nodes brick element for butt weldment and 8 nodes shell element for base metal. According to FEA results, the longitudinal compressive strain inducing tensile residual stress at the butt weldment decreased. It was because the compressive thermal strain in way of weldment was reduced by tension load. The control effect of residual stress increased with an increase in tension load. So, if the amount of tension load applied to the weldment exceeds 1.5 times of longitudinal shrinkage force, the amount of longitudinal residual stress decreased below the critical value inducing the buckling distortion at the SA butt weldment. Its validity was verified by experiment.

• 대한조선학회논문집
• /
• 제44권6호
• /
• pp.590-597
• /
• 2007

The portion of thin plate is expected to increases as to the development of design and fabrication technology. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates, and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper is aimed at applying the mechanical tensioning method to fillet weld of thin plates to reduce the weld-induced deformation. For this purpose, fillet welding tests have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. From the present study, it has been found that the tensioning method is effective on reduction of weld-induced deformation.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.197-200
• /
• 2006

The portion of thin plate is expected to increases as to the development of design and fabrication technology. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates, and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to fillet weld of thin plates to reduce the weld-induced deformation. For this, fillet welding test have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. From the present study, it has been found that the tenssoning method is effective on reduction of weld-induced deformation.