• 한국수자원학회논문집
• /
• 제48권4호
• /
• pp.299-308
• /
• 2015

본 연구의 목적은 하천에서 흐름방향 유속의 횡분포식에 기반하여 1차원 종분산계수를 이론적으로 유도하고 이들의 타당성을 검증하는 것이다. 이를 위해 본 논문의 전편 "I. 흐름방향 유속의 횡포식"에서는 SKM을 도입하여 삼각형 단면수로에서 횡분포식을 해석적으로 유도하였다. 본 논문의 후편 "II. 종분산계수"에서는 전편에서 유도된 유속의 횡분포식을 기반으로 1차원 종분산계수 이론식을 새롭게 개발하였다. 개발된 종분산계수 이론식을 검증하기 위해 전편과 동일한 하천에서 수행된 추적자 농도 실험 결과를 이용한 관측 종분산계수와 비교 분석하였다. 또한 개발된 종분산 계수식을 기존의 식들과 비교하여 본 연구에서 개발된 식의 차별점 및 우수성을 검토하였다. 결과적으로 무차원 종분산계수는 무차원 횡확산계수에 반비례하고, 하폭 대 수심비의 제곱에 비례하였다. 그리고 Manning의 조도계수의 제곱에 반비례함을 확인할 수 있었다.

• 상하수도학회지
• /
• 제21권5호
• /
• pp.581-587
• /
• 2007

In order to suggest the methodology for improving the equality of flow distribution in a distribution channel, wet tests were carried out for pilot plant which was scaled down to 1/8 of full scale distribution channel being operated in domestic K_water treatment plant. The correlation between various hydraulic variables and their effects on the equality of flow distribution was evaluated through wet tests using pilot plant. From the results of wet tests, the longitudinal baffle with orifices was installed in the distribution channel, the equality of flow distribution was improved on the condition that the Froude number in pilot plant was similar with that in the full scale channel. Also, the opening ratio of the orifices on the longitudinal baffled did not have influence on the performance of the equality of flow distribution when the average flow velocity and Froud number were relatively low (Froude number ${\fallingdotseq} 0.01$). In the other hand, the performance of the equality of flow distribution was improved with increasing the opening ration of on the longitudinal baffle under conditions of relatively high average flow velocity and high Froud number(${\gtrsim}0.1$)

• 소성∙가공
• /
• 제23권6호
• /
• pp.369-375
• /
• 2014

Flexible roll forming allows profiles to have variable cross-sections. However, the profile may have some shape errors, such as, warping which is a major defect. The shape error is induced by geometrical deviations in both the concave zone and the convex zone. In the current study, flexible roll forming was modeled with FE simulations to analyze the shape error and the longitudinal strain distribution along the flange section over the profile. A distribution of analytically calculated longitudinal strains was used to develop relationships between the shape error and the longitudinal strain distribution as a function of the defined shape parameters for the profile. The FE simulations showed that the shape error is primarily affected by the deviations between the distribution of analytically calculated longitudinal strain and the longitudinal strain distribution of the profile. The results show that the shape error can be controlled by designing the shape parameters to control the geometrical deviations at the flange section in the transition zones.

• 한국수자원학회논문집
• /
• 제39권12호
• /
• pp.1023-1030
• /
• 2006

종방향 유속의 특성을 파악하기 위해서 중심각이 $180^{\circ}$인 순환수로에서 실험을 수행하였으며, 3차원 유속장 측정은 측방 음파 도플러 유속계를 이용하였다. 기존의 종방향 유속식들의 단점들을 검토하였다. 종방향 운동 방정식에 와점성 개념을 도입하여 새로운 종방향 유속의 연직분포 식을 개발하였다. 종방향 유속의 연직분포들을 비교한 결과 잘 일치함을 보여주고 있으며, 곡선수로에서 곡률의 변화는 종방향 유속의 연직분포 변화 및 최대 유속 발생 지점에 영향을 미치는 것을 발견하였다.

• 비파괴검사학회지
• /
• 제29권6호
• /
• pp.586-590
• /
• 2009

Poisson's ratio, one of elastic constants of elastic solids, has not attracted attention due to its narrow range and difficult measurement. Transverse wave velocity as well as longitudinal wave velocity should be measured for nondestructive measurement of Poisson's ratio. Rigid couplants for transverse wave is one of obstacle for scanning over specimen. In the present work, a novel measurement of Poisson's ratio distribution was applied. Immersion method was employed for the scanning over the specimen. Echo signals of normal beam longitudinal wave were collected, and transverse wave modes generated by mode conversion were identified. From transit time of longitudinal and transverse waves, Poisson's ratio was determined without the information of specimen thickness. Poisson's ratio distribution of the carbon steel weldment was mapped. Heat affected zone of the weldment was clearly distinguished from base and filler metals.

• Smart Structures and Systems
• /
• 제19권3호
• /
• pp.309-322
• /
• 2017

In this paper, the buckling, and free vibration analysis of tapered functionally graded carbon nanotube reinforced composite (FG-CNTRC) micro Reddy beam under longitudinal magnetic field using finite element method (FEM) is investigated. It is noted that the material properties of matrix is considered as Poly methyl methacrylate (PMMA). Using Hamilton's principle, the governing equations of motion are derived by applying a modified strain gradient theory and the rule of mixture approach for micro-composite beam. Micro-composite beam are subjected to longitudinal magnetic field. Then, using the FEM, the critical buckling load, and natural frequency of micro-composite Reddy beam is solved. Also, the influences of various parameters including ${\alpha}$ and ${\beta}$ (the constant coefficients to control the thickness), three material length scale parameters, aspect ratio, different boundary conditions, and various distributions of CNT such as uniform distribution (UD), unsymmetrical functionally graded distribution of CNT (USFG) and symmetrically linear distribution of CNT (SFG) on the critical buckling load and non-dimensional natural frequency are obtained. It can be seen that the non-dimensional natural frequency and critical buckling load decreases with increasing of ${\beta}$ for UD, USFG and SFG micro-composite beam and vice versa for ${\alpha}$. Also, it is shown that at the specified value of ${\alpha}$ and ${\beta}$, the dimensionless natural frequency and critical buckling load for SGT beam is more than for the other state. Moreover, it can be observed from the results that employing magnetic field in longitudinal direction of the micro-composite beam increases the natural frequency and critical buckling load. On the other hands, by increasing the imposed magnetic field significantly increases the stability of the system that can behave as an actuator.

• 제어로봇시스템학회논문지
• /
• 제16권7호
• /
• pp.632-638
• /
• 2010

This paper presents an optimum tire force distribution method for 6WD/6WS(6-Wheel-Drive and 6-Wheel-Steering) electric vehicles. Using an independent steering and driving system, the performance of 6WD/6WS vehicles can be improved, as, for example, with respect to their maneuverability under low speed and their stability at high speed. Therefore, there should be a control strategy for finding the optimum tire forces that satisfy the driver's command and minimize energy consumption. From the driver's commands (steering angle and accelerator/brake pedal stroke), the desired yaw moment, the desired lateral force, and the desired longitudinal force were obtained. These three values were distributed to each wheel as the torque and the steering angle, based on the optimum tire force distribution method. The optimum tire force distribution method finds the longitudinal/lateral tire forces of each wheel that minimize the cost function, which is the sum of the normalized tire forces. Next, the longitudinal/lateral tire forces of each wheel are converted into the reference torque inputs and the steering wheel angle inputs. The proposed method was tested through a simulation, and its effectiveness was verified.

• 유통과학연구
• /
• 제20권11호
• /
• pp.89-98
• /
• 2022

Purpose: Increasing competition in the higher education sector has prompted universities to enhance their marketing efforts and understand their potential customers. The study aims to explore how information sources are used and changed among prospective Vietnamese students during the decision-making process. Research Design, Data, and Methodology: This study undertakes a longitudinal study involving multiple rounds of data collection to better understand the decision-making process of prospective students. Data was collected from 12th -grade students in Vietnam through two rounds of quantitative surveys with 251 students and one round of qualitative interviews, spanning the duration of their senior year. The three stages of the decision-making process correspond to the three stages of pre-purchase period. Results: Most students decide that attending open days, taking career assessments, and looking up information online are the most important information sources to consider. The WOM sources are more important in the early stages, while university-generated sources and events are important in the later stages. Conclusion: Implications from this study may contribute to the design of more effective marketing communications campaigns as university marketers gain a better understanding of the distribution of information sources utilized for each specific stage of the decision-making process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.101-103
• /
• 1996

Multiply-twist cable is used for a large capacity superconducting cable because it is helpful to reduce AC losses and to increase transport current. In a multiply-twisted cable, the axis of a strand does not coincide with that of cable. Therefore, the longitudinal field is generated by the transport current. The longitudinal field changes the current distribution in the strand and generates additional AC loss. This paper calculates the longitudinal field that is applied to a strand in the multiply-twisted cable. Current distribution of a strand in the cable is also presented. 2nd level superconducting cable is chosen as an analysis model, whose current capacity is 2000A. Calculation result shows the longitudinal field cannot be neglected in low field machines such as superconducting transformer.

• Steel and Composite Structures
• /
• 제22권4호
• /
• pp.837-853
• /
• 2016

This paper presents the experimental and numerical study on the distribution of transverse and longitudinal residual stresses in cold-formed thick-walled structural steel rectangular hollow sections manufactured by indirect technique. Hole-drilling method is employed to measure the magnitude of the transverse and longitudinal surface residual stress distribution, and the effects of the residual stresses are evaluated qualitatively by sectioning method. It is shown that compared to normal cold-formed thin-walled structural hollow sections (SHS), the cold-formed thick-walled SHS has similar level of residual stress in the flat area but higher residual stresses in the corner and welding areas. Both the transverse and longitudinal residual stresses tend to open the section. In order to predict the surface residual stresses in the corners of the cold-formed thick-walled SHS, an analytical model is developed. 2D finite element simulation of the cold bending process is conducted to validate the analytical approach. It is shown that in analyzing bending for thick-walled sections, shifting of neutral axis must be considered, since it would lead to nonlinear and non-symmetrical distribution of stresses through the thickness. This phenomenon leads to the fact that cold-formed thick-walled SHSs has different distribution and magnitude of the residual stresses from the cold-formed thin-walled SHSs.