• Wind and Structures
• /
• 제22권1호
• /
• pp.65-87
• /
• 2016

The wind velocity profile over the height of a structure in high intensity wind (HIW) events, such as downbursts, differs from that associated with atmospheric boundary layer (ABL) winds. Current design codes for lattice transmission structures contain only limited advice on the treatment of HIW effects, and structural design is carried out using wind load profiles and response factors derived for ABL winds. The present study assesses the load-deformation curve (capacity curve) of a transmission tower under modeled downburst wind loading, and compares it with that obtained for an ABL wind loading profile. The analysis considers nonlinear inelastic response under simulated downburst wind fields. The capacity curve is represented using the relationship between the base shear and the maximum tip displacement. The results indicate that the capacity curve remains relatively consistent between different downburst scenarios and an ABL loading profile. The use of the capacity curve avoids the difficulty associated with defining a reference wind speed and corresponding wind profile that are adequate and applicable for downburst and ABL winds, thereby allowing a direct comparison of response under synoptic and downburst events. Uncertainty propagation analysis is carried out to evaluate the tower capacity by considering the uncertainty in material properties and geometric variables. The results indicated the coefficient of variation of the tower capacity is small compared to those associated with extreme wind speeds.

• 산업경영시스템학회지
• /
• 제35권2호
• /
• pp.30-36
• /
• 2012

This study is aimed to show that an asymmetric load in the frontal plane leads to an increase in low back loading and fatigue in comparison with a symmetric load when workers lift an external weight by investigating previous studies and verifying the phenomenon with an experiment. Ten male subjects are required to lift and hold an given external load at 70cm height during 50sec, then the EMG amplitude and median frequency on bilateral low back muscle groups (Longissimus, Iliocostalis, and Multifidus) are recorded and analyzed. Independent variables are two-level load weight (13kg, 20kg) and three-level LCG (Center, 6.5cm to the right, and 13cm to the right), and dependent variables are EMG amplitude average, difference, and Fatigue Index (FI). Results show that load weight increases significantly amplitude average and FI, but LCG does significantly amplitude difference and FI significantly (P-value < 0.05). Also the correlation coefficient between amplitude difference and FI is over 0.99. These implies that trunk loading should be explained by not EMG amplitude but muscle fatigue aspect since the association between an external load and amplitude is linear, but the relationship between an external load and median frequency as muscle fatigue index is almost exponential.

• 한국지반공학회논문집
• /
• 제20권8호
• /
• pp.41-48
• /
• 2004

이 연구에서는 아직 국내에서는 시공실적이 없는 쇄석다짐말뚝(Gravel Compaction pile)공법의 적용성을 판단하기 위하여 SCP와 GCP의 모형토조시험을 수행하였다. 즉, 원통형 압밀상자(지름 20cm, 높이 40cm)에 치환율 30, 40, 50, 60, 70%로 달리 조성하여 원심력 압밀시험기를 이용하여 압밀시킨 후, 재하시험을 통하여 두 공법의 지지력 특성을 비교 검토하였다. 또한 모형시험을 통해 얻어진 극한지지력을 기존에 제안된 SCP 및 GCP 시공지반의 극한지지력 산정식을 이용한 계산값과 비교하였다. 모형시험 결과 GCP 시공지반이 SCP 시공지반에 비해 지지력 측면에서 더 우수한 것으로 나타났다.

• Computers and Concrete
• /
• 제28권5호
• /
• pp.479-486
• /
• 2021

Reinforced concrete (RC) slabs are exposed to several static and dynamic effects during their period of service. Accordingly, there are many studies focused on the behavior of RC slabs under these effects in the literature. However, impact loading which can be more effective than other loads is not considered in the design phase of RC slabs. This study aims to investigate the dynamic behavior of two-way RC slabs under sudden impact loading. For this purpose, 3 different simply supported slab specimens are manufactured. These specimens are tested under impact loading by using the drop test setup and necessary measurement devices such as accelerometers, dynamic load cell, LVDT and data-logger. Mass and drop height of the hammer are taken constant during experimental study. It is seen that rigidity of the specimens effect experimental results. While acceleration values increase, displacement values decrease as the sizes of the specimens have bigger values. In the numerical part of the study, artificial neural networks (ANN) analysis is utilized. ANN analysis is used to model different physical dynamic processes depending upon the experimental variables. Maximum acceleration and displacement values are predicted by ANN analysis. Experimental and numerical values are compared and it is found out that proposed ANN model has yielded consistent results in the estimation of experimental values of the test specimens.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2022년도 춘계학술대회
• /
• pp.346-348
• /
• 2022

적재폐기물에서 발생하는 발효열의 발화요인 분석 자료를 기반으로 발생 원인을 규명하는 모니터링 시스템을 구성하였다. 화재 조기경보 유형별 시나리오의 구성과 신속성을 위해 실시간 런타임 환경을 제공하기 위한 유니버설미들웨어를 활용하였다. 적재폐기물의 적재 높이와 압력, 대표적인 구성폐기물인 목재, 건전지, 플라스틱 폐기물의 건조, 표면의 탄화변화를 동적으로 인지해야 한다. 따라서, 저온발화 화재 가능성 데이터 분석을 위한 IoT 상황인지 플랫폼을 동적으로 구성하여 제시하였다.

• Geomechanics and Engineering
• /
• 제32권1호
• /
• pp.97-110
• /
• 2023

The coefficient of lateral earth pressure at rest in loose sand during virgin loading, K₀ , and during unloading, K'₀ , have been determined from laterally confined load-unload tests. The tests included measurement of lateral pressure with null pressure gauges, side wall friction with newly designed friction meters and applied pressure and base pressure with load cells. The importance of accounting for side-wall friction when evaluating the distribution of vertical pressure over the height of the soil specimen was demonstrated. Relatively uniform friction was observed during loading, but this was not the case during unloading unless friction reduction measures were employed. While the measured value of K₀ was found to be close to, if slightly higher than the value commonly estimated on the basis of friction angle, φ', the ratio of K'₀ to K₀ was found to reasonably fit an expression of the form K'₀/K₀ = 1 + C·log(OCR), with C equal to 1 in the present tests.

• 수산해양기술연구
• /
• 제47권3호
• /
• pp.241-247
• /
• 2011

Marine casualties of vessel are said to be in most case caused by human error, but it would be valid for the assumption that the ship is built with high quality and then should be acceptable to the safety standards. It means that the inherent characteristics of a ship should be the first consideration on the safety of ship. Therefore it is basically necessary for navigator to grasp the inherent stability of his ship and ensure that the ship complies with the minimum statutory standards of stability. This study is to realize the stability of the Korean offshore large purseiner varying with loading conditions by the inclining data and some calculations. The author compared the stability of the ship with IMO criteria and domestic rule, and proposed some improvement for the safety of the ship. The results are summarized as follows ; The values of GM of the ship according to the loading condition in navigation satisfy both of the IMO criteria and the domestic rule, but in case of the area under the GZ curves between the heel angles of $30^{\circ}$ and $40^{\circ}$, and the heel angle occuring the maximum righting lever not satisfy the IMO rule at the fishing ground departure and arrival conditions in the haul in net situation. The initial metacentric height of the ship is very large, but the range of stability and the occurring angle of the maximum GZ are very small, so even small inclining can bring about the beam end. The best method of improvement for that is to increase the freeboard of the model among the variables.

• 대한토목학회논문집
• /
• 제40권2호
• /
• pp.197-208
• /
• 2020

본 연구에서는 콘크리트 원형 교각의 동적거동 특성을 향상시키기 위하여 최적의 탄소섬유강화 플라스틱 설치 방법에 대해서 해석적 기법을 적용하여 평가하였다. 범용구조해석 프로그램인 ABAQUS가 해석연구에 사용되었으며, 소성 및 손상 콘크리트 재료특성을 적용하여 구조물의 비선형해석을 실시하였다. CFRP 적용에 따른 내진성능 향상도를 분석하고자 교각높이와 보강된 높이 비율, 교각 지름 대비 CFRP 보강 두께를 해석변수로 고려하여 거동특성과 연성도를 비교 분석하였다. 해석결과를 토대로 보강에 따른 정량적인 성능향상을 확인할 수 있었으며, 보강 재료 두께 증가보다는 교각높이 대비 보강높이 비율이 보다 성능에 큰 영향을 미치는 것을 알 수 있었다.

• 대한인간공학회지
• /
• 제26권2호
• /
• pp.35-44
• /
• 2007

Work-related musculoskeletal disorders (WMSDs) are a major problem in industries in which manual materials handling is performed by workers. To prevent these WMSDs, it is necessary to understand the muscular strength capability and use this knowledge to design job and selection and assignment of workers. Even though two-hands lifting activity of manual materials handling tasks are prevalent at the industrial site, many manual materials handling tasks which require the worker to perform one-hand lifting are also very common at the industrial site and forestry and farming. However, a few researches have been done for one-hand lifting activity of manual materials handling tasks. The objective of this study is to compare one-hand and two-hands lifting strength in terms of static and dynamic strength of the lifting activity for the ranging from the height of knuckle to elbow. It is shown in this study that the isometric lifting strength of one-hand is ranging from 54.7 to 63.3% of the one of two-hands. However, it is found that there is no significant difference between a person's isometric lifting strength for left-hand and right-hand. It is also shown that there is no significant difference between the peak force under the dynamic sub-maximal loading with one-hand and two-hands lifting activity. Similar results were obtained for the peak acceleration and peak velocity under the dynamic sub-maximal loading with one-hand and two-hands lifting activity. Isometric lifting strength at the height of knuckle was ranging from 2 to 3 times of the dynamic peak force during sub-maximal lifting. It is concluded that the dynamic peak forces under the sub-maximal loading are not highly correlated with the isometric lifting strength in similar postures.

• Geomechanics and Engineering
• /
• 제19권2호
• /
• pp.105-114
• /
• 2019

In this paper, simulation tests were conducted with similar materials to study the distribution of residual voids in longwall goaf. Short-time step loading was used to simulate the obvious deformation period in the later stage of arch breeding. Long-time constant loading was used to simulate the rheological stage of the arch forming. The results show that the irregular caving zone is the key area of old goaf for the subsidence control. The evolution process of the stress arch and fracture arch in stope can be divided into two stages: arch breeding stage and arch forming stage. In the arch breeding stage, broken rocks are initially caved and accumulated in the goaf, followed by the step deformation. Arch forming stage is the rheological deformation period of broken rocks. In addition, under the certain loads, the broken rock mass undergoes single sliding deformation and composite crushing deformation. The void of broken rock mass decreases gradually in short-time step loading stage. Under the water lubrication, a secondary sliding deformation occurs, leading to the acceleration of the broken rock mass deformation. Based on above research, the concept of equivalent height of residual voids was proposed, and whose calculation equations were developed. Finally, the conceptual model was verified by the field measurement data.