• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.122-129
• /
• 2004

Finite element analysis was performed to analyze structural safety of a new heavy-duty direct injection diesel engine. A half section of the in-line 6-cylinder engine was selected as a computational domain. A mapping method was used to project heat transfer coefficients from CFD results of engine coolant flow onto the FE model. The accurate setting of thermal boundary condition on the FE model was expected to result in improved prediction of temperature, cylinder bore distortion, and stresses. Characteristics of high cycle fatigue were investigated by assuming the engine was operated under the following five loading conditions repeatedly; assembly force, assembly force with thermal loading, alternating maximum gas pressure loading at each cylinder combined with assembly force and thermal loading. Distribution of fatigue safety factor was calculated by using it Haigh diagram in which the maximum and the minimum stresses were selected from the five loading cases.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.1-10
• /
• 2002

As the preliminary stage for the countermeasure of thermal loading in miller cycle engine, coolant flows in the cylinder head of base engine including exhaust valve bridge were visualized and analyzed by using PIV technique. It was found that low coolant velocity regions were around exhaust valve bridge, around which stagnation of the coolant flow was observed due to the complex geometry configuration of water jacket. And velocity variation between each cylinder was remarkable. For the countermeasure of these, it is necessary to enhance coolant flow around exhaust valve bridge and to improve the deviation of coolant flow between each cylinder.

• 한국지진공학회논문집
• /
• 제1권2호
• /
• pp.31-37
• /
• 1997

삼국시대 이후 근대까지 민가의 가장 보편적인 형태였던 초가삼가의 평균적인 상세 구조를 제시하였다. 목조 프레임이 주로 사용되었으며 프레임의 조인트는 사개맞춤이 일반적이었다. 초가삼간을 구성하는 평주 및 고주 프레임의 정적 수평내력을 1:1 실험모델을 통하여 평가하였다. 기둥 상부 조인트의 형태 및 심벽이 수평내력에 미치는 영향과 조인트의 파괴모드를 분석하였다. 실험결과 평주 프레임의 극한 수평내력은 1,090N, 파괴시 최대 수평변위는 400mm(1/6 rad)이었다. 고주 프레임의 경우 이들 값은 각각 4,160 N 및 250 mm(1/9.6 rad)이었다. 프레임의 거동은 모두 조인트의 거동에 지배되었으며 매우 큰 비선형을 보였다. 조인트의 파괴모드는 평주 프레임의 경우 화통가지의 전단파괴, 고주프레임의 경우 화통가지의 휨파괴가 주요한 모드였다.

• 한국정밀공학회지
• /
• 제25권1호
• /
• pp.145-150
• /
• 2008

One of the unresolved questions in articular cartilage biomechanics is the magnitude of the dynamic modulus and tissue compressive strains under physiological loading conditions. The objective of this study was to characterize the dynamic modulus and compressive strain magnitudes of bovine articular cartilage at physiological compressive stress level and loading frequency. Four bovine calf shoulder joints (ages 2-4 months) were loaded in Instron testing system under load control, with a load amplitude up to 800 N and loading frequency of 1 Hz, resulting in peak engineering stress amplitude of ${\sim}5.8\;MPa$. The corresponding peak deformation of the articular layer reached ${\sim}27%$ of its thickness. The effective dynamic modulus determined from the slope of stress versus strain curve was ${\sim}23\;MPa$, and the phase angle difference between the applied stress and measured strain which is equivalent to the area of the hystresis loop in the stress-strain response was ${\sim}8.3^{\circ}$. These results are representative of the functional properties of articular cartilage in a physiological loading environment. This study provides novel experimental findings on the physiological strain magnitudes and dynamic modulus achieved in intact articular layers under cyclical loading conditions.

• Geomechanics and Engineering
• /
• 제16권5호
• /
• pp.463-469
• /
• 2018

In offshore engineering, lateral cyclic loading may induce excessive lateral movement and bending strain in pile foundations. Previous studies mainly focused on deformation mechanisms of single piles due to lateral cyclic loading. In this paper, centrifuge model tests were conducted to investigate the response of a $2{\times}2$ pile group due to lateral cyclic loading in clay. After applying each loading-unloading cycle, the pile group cannot move back to its original location. It implies that residual movement and bending strain are induced in the pile group. This is because cyclic loading induces plastic deformation in the soil surrounding the piles. As the cyclic load increases from 62.5 to 375 kN, the ratio of the residual to the maximum pile head movements varies from 0.30 to 0.84. Moreover, the ratio of the residual to the maximum bending strains induced in the piles is in a range of 0.23 to 0.82. The bending strain induced in the front pile is up to 3.2 times as large as that in the rear pile. Thus, much more protection measures should be applied to the front piles to ensure the serviceability and safety of pile foundations.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.664-667
• /
• 1995

The purpose of this paper is to consider the disk failure phenomenon based on the second kind Fredholm integral equation and numerical inversion of Laplace transform when the head hit disk asperities at HDI under antiplane impact loading. The model for analysis is a two layeered half-space with a circumferential surface edge crack. The optimum design parameters to reduce the disk failure due to impact are presented

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 춘계학술대회 논문요약집
• /
• pp.140-140
• /
• 2004

마이크로 기술을 대변하는 Micro-Electro-Mechanical-Systems (MEMS)와 반도체, 각종 micro-sensor 및 actuator 등은 실리콘 위에 박막 코팅한 재료를 주로 사용하고 있다. 따라서 1 Um 이하의 박막코팅에 의해 원하는 성능을 얻으려는 시도가 널리 진행되고 있다 Hard Disk Drive (HDD)의 Head-Disk Interface (HDI)와 MEMS 접촉면에서는 발생하는 마찰 및 마멸에 대한 문제 등은 중요한 고려대상이다. 특히 코팅 층의 표면 파손 현상은 코팅 층의 파손 특성과 코팅 층과 기판 사이의 결합상태가 큰 영향을 미친다.(중략)

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권5호
• /
• pp.762-772
• /
• 2004

Fatigue life of a Piston for large liquid Petroleum liquid injection(LPLi) bus engines is analyzed considering effects of cooling condition parameters : temperature of cooling water, and heat transfer coefficients at oil gallery and bottom surface of piston head. Temperature of the piston is analyzed with varying cooling conditions Stresses of the piston from two load cases of pressure loading. and pressure and thermal loading are analyzed Fatigue life under repeated peak pressure and thermal cycle is analyzed by the strain-life theory. For the two load cases, required loading cycles for engine life are defined, and loading cycles to failure and partial damages are calculated. Based on the resulting accumulated fatigue usage factors, endurance of the piston is evaluated and effects of varying cooling condition Parameters are discussed.

• 자동차안전학회지
• /
• 제12권1호
• /
• pp.39-45
• /
• 2020

The express/intercity bus models have been developing for wheelchair users to provide the preferable long-distance travels by the Korean government research. In the previous studies, evaluation method was set up for the wheelchair users' safety and the study for wheelchair occupants' safety was performed under various crash loadings mimic to real accidents, frontal crash, side impact and rollover, etc. This study was focused on the evaluation of occupant behaviors and injuries (head and chest) during vehicle impact loading cases in order to ensure the safety of wheelchair passengers in the bus. The occupant response and belt loading data during the sled FE simulation were compared with those of the sled test. The simulation results showed overall safety tolerances of wheelchair occupants under the severe frontal deceleration, side impact loading based on the FMVSS 214 configuration and bus rollover loading.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.28-38
• /
• 2003

Finite element analysis of cylinder heat/block compound under assembly, thermal and firing condition were performed. FE model including two cylinders with gasket, head bolts, liners and valve seats was used. FE modeling method and boundary conditions were introduced. Stress distribution and deformation of cylinder head and block under each loading condition were presented. Gasket pressure distribution and bore distortion level were predicted. Measured data of bore distortion was compared with the analysis results. The analysis result showed similar trends with the experimental data. High cycle fatigue analysis on the basis of this result has been performed in order to find the critical areas of the engine assembly.