• Journal of Wetlands Research
• /
• v.9 no.2
• /
• pp.57-69
• /
• 2007

This study focused on coastal water quality response to land-based and sediment pollution loads and estimation of the carrying capacity in Masan Bay using an ecological model with the data in summer of 2002. A residual current was simulated to have a slightly complicated pattern with ranging from 0.1 to 1.5 cm/s. In Masan Bay, pollutant materials cannot flow from the inner to the outer bay easily because of residual currents flow southward at surface and northward at the bottom. The simulation results of COD distribution showed high concentrations over 3 mg/L in the inner part of Masan Bay related pollutant discharge. For improvement seawater quality grade I in Masan Bay, it is necessary to reduce the organic and inorganic loads from point sources by more than 80%. For improvement seawater quality grade II, it is necessary to reduce the organic and inorganic loads from point sources by more than 50% and ameliorate severe polluted sediment. The carrying capacity for COD is 2.32 ton/day and 7.16 ton/day for each grade.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.9
• /
• pp.1669-1673
• /
• 2008

A new cycle ergometer using a Magneto-Rheological (MR) rotary brake system has been developed for rehabilitation of hemiplegia patients to reduce uneven pedaling characteristics. For this purpose, a control method to adjust the resistance of the MR rotary brake in real time based on the magnitude of the muscular force exerted by the subject has been devised so that the mechanical resistance to the pedaling can be minimized when the affected leg was engaged for pedaling. A series of experiments were carried out with and without the engagement of this real-time control mode of MR rotary brake at different pedaling rate to find out the effect of the real-time control mode. The characteristics of the pedaling for these specific conditions were analyzed based on the variations in angular velocities of the pedal unit. The results showed that the variations in the angular velocities were decreased by 42.9% with the control mode. The asymmetry of pedaling between dominant and non-dominant leg was 19.63% in non-control mode and 1.97% in the control mode. The characteristics of electromyography(EMG) in the lower limbs were also measured. The observation showed that Integrated EMG(IEMG) reduced with the control mode. Therefore, the new bicycle system using MR brake with the real time control of mechanical resistance was found to be effective in recovering the normal pedaling pattern by reducing unbalanced pedaling characteristics caused by disparity of muscular strength between affected and unaffected leg.

• KIISE Transactions on Computing Practices
• /
• v.21 no.2
• /
• pp.138-143
• /
• 2015

The Boyer-Moore algorithm is a single pattern string matching algorithm that is widely used in various applications such as computer and internet security, and bioinformatics. This algorithm is computationally demanding and requires high-performance parallel processing. In this paper, we propose a parallelization and performance optimization methodology for the BM algorithm on a GPU. Our methodology adopts an algorithmic cascading technique. This results in significant reductions in the mapping overheads for the threads participating in the parallel string matching. It also results in the efficient utilization of the multithreading capability of the GPU which improves the load balancing among threads. Our experimental results show that this approach achieves a 45-times speedup at maximum, in comparison with a serial execution.

• Journal of Information Processing Systems
• /
• v.5 no.1
• /
• pp.33-40
• /
• 2009

Ever since the network-based malicious code commonly known as a 'worm' surfaced in the early part of the 1980's, its prevalence has grown more and more. The RCS (Random Constant Spreading) worm has become a dominant, malicious virus in recent computer networking circles. The worm retards the availability of an overall network by exhausting resources such as CPU capacity, network peripherals and transfer bandwidth, causing damage to an uninfected system as well as an infected system. The generation and spreading cycle of these worms progress rapidly. The existing studies to counter malicious code have studied the Microscopic Model for detecting worm generation based on some specific pattern or sign of attack, thus preventing its spread by countering the worm directly on detection. However, due to zero-day threat actualization, rapid spreading of the RCS worm and reduction of survival time, securing a security model to ensure the survivability of the network became an urgent problem that the existing solution-oriented security measures did not address. This paper analyzes the recently studied efficient dynamic network. Essentially, this paper suggests a model that dynamically controls the RCS worm using the characteristics of Power-Law and depth distribution of the delivery node, which is commonly seen in preferential growth networks. Moreover, we suggest a model that dynamically controls the spread of the worm using information about the depth distribution of delivery. We also verified via simulation that the load for each node was minimized at an optimal depth to effectively restrain the spread of the worm.

• Restorative Dentistry and Endodontics
• /
• v.14 no.1
• /
• pp.179-188
• /
• 1989

The purpose of this study was to measure Micro vicker's hardness of 4 kinds of anterior Composite resins (Pyrofil light bond anterior, Lite-fil anterior, Photo clear fil anterior, Silux) and 6 kinds of posterior Composite resin (Pyrofil light bond posterior. Lite-fil posterior, Photo clear fil posterior, Occlusin posterior, Palfique light posterior, P-30, posterior) according to deference of depth and distance of light tip from surface of composite resin. Each composite resin was filled into Teflon tube of 5mm in diameter and 5mm in depth, celluloid matrix was covered and the light in accordance with each composite resin was irradiated in distance of zero millimeter and 1 cm from light tip to surface of composite resin for 30 seconds. Specimens were sectioned longitudinally with cutting device. Microvicker's hardness measurements ware made at the depth of surface, 1mm, 2mm, 3mm, 4mm and 5mm from the surface to deep portion. Vicker's hardness numbers were taken on each depth under 200gm load for 30 seconds with MVK-E. The following results were: 1. The highest hardness value was measured at 1 mm depth. Then the deeper the depth, the lesser the hardness was observed. 2. The hardness value of anterior composite resins is lower than one of posterior composite resins. 3. Hardness number of composite resin irradiated in distance of zero millimeter from surface of composite resin was higher than one of 1 cm from surface of composite resin. 4. The pattern of hardness change at varying depth was similar to all the experimental material with no relation to distance of light from specimen.

• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.2
• /
• pp.293-301
• /
• 1998

The purpose of this study was to investigate the effects of load on root that was applied to edentulous area in three simulated situation, in each case the guiding planes of abutment were right vertical, 95 degrees, or 100 degrees to residual ridge. The 2-dimensional finite element method was used and the finite element model was prepared as fellows. Right mandibular 1st and 2nd molar was lost and the 2nd premolar with distal rest was used as primary abutment which had three different degrees of guiding plane. Then 150N of compressive force was applied to central fossae of the 1st and 2nd molars and von Mises stress and displacement was measured. The results were as follows; 1. Irrespective of slopes of guiding planes, the stress was concentrated on mesial side of root apex and distal side of coronal portion of root, in particular on junction with distal alveolar bone. As slopes of guiding planes were increased. stress on root and compact bone surrounding abutment was increased but no considerable effect was seen on compact bone of residual ridge. 2. Distal side of coronal portion of root limited by periodontal ligament was displaced distally and mesial side of apical portion was mesially. With slope of guiding plane increasing, the pattern of displacement was similar with one another but the quantity was increased. 3. Both abutment & alveolar bone were displaced downward and root of abutment, especially distal side of coronal portion, was displaced severely. As the guiding plane was tiffed more mesially over $90^{\circ}$, the degree of displacement was also increased.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.4
• /
• pp.209-219
• /
• 2007

The purpose of this study was to analyze biomechanical mechanism (posture, moment of back joint, EMG) when athletes (Judo, Ssirum) and lay people lifted a load according to two different lift methods; backlift and leglift. The number of subjects was 12; 8 athletes (4 for Judo, 4 for Ssirum) and 4 lay people. We recorded a lift motion in backlift and leglift using 7 real time infrared cameras (vicon) and analyzed EMG pattern of major muscles for a lift (lattisimus dorsi, erector spinae, biceps femoris). In a backlift Judo players showed a biggest range of back flexion and extension motion and lay people flexed more than other groups at phase 2 in which an interaction between groups and events was statistically significant (p=.024). In a leglift Ssirum players more flexed their back in a barbell lift and there was a statistical significance (p=.021) between groups and events. For moment of back joints, 1) in a backlift a larger loading on back joints in all three groups at phase 2 when lifting down a barbell, 2) in a leglift a larger loading on back joints when lifting down a barbell in two athlete groups but a larger loading when lifting up a barbell in lay people group, and all groups did not show any statistical significance. For EMG, right lattisimus dorsi muscle in a backlift was statistical significant (p=.006) in an interaction between groups and phase but left lattisimus dorsi muscle was insignicant, and there was not any significance in a leglift. Generally atheletes (Judo and Ssirum) used more their muscles of lower extremity in lifting up and down and lay people did more their ones of upper extremity.

• Tribology and Lubricants
• /
• v.32 no.4
• /
• pp.119-124
• /
• 2016

In the sapphire wafering process, lapping is a crucial operation in order to reduce the damaged layer and achieve the target thickness. Many parameters, such as pressure, velocity, abrasive, slurry and plate, affect lapping characteristics. This paper presents an experimental investigation on the effect of the plate groove on the material removal rate and roughness of the wafer. We select the spiral pattern and rectangular type as the groove shapes. We vary the groove density by controlling the groove shape dimension, i.e., the groove width and pitch. As the groove density increases to 0.4, the material removal rate increases and gradually reaches a saturation point. When the groove density is low, the pressing load is mostly supported by the thick film, and only a small amount acts on the abrasives resulting to a low material removal rate. The roughness decreases on increasing the groove density up to 0.3 because thick film makes partial participations of large abrasives which make deep scratches. From these results, we could conclude that the groove affects the contact condition between the wafer and plate. At the same groove density, the pitch has more influence on reducing the film thickness than the groove width. By decreasing the groove density with a smaller pitch and larger groove width, we could achieve a high material removal rate and low roughness. These results would be helpful in understanding the groove effects and determining the appropriate groove design.

• Transactions of Materials Processing
• /
• v.17 no.8
• /
• pp.633-642
• /
• 2008

It's important to measure quantitative properties about thermal-nano behavior of polymer for producing high quality components using Nanoimprint lithography process. Nanoscale indents can be used to make the cells for molecular electronics and drug delivery, slots for integration into nanodevices, and defects for tailoring the structure and properties. In this study, formability of polymethylmetacrylate(PMMA) and polycarbonate(PC) were characterized Polymer has extreme variation in thermo mechanical variation during forming high temperature. Because of heating the polymer, it becomes softer than at room temperature. In this case it is particularly important to study high temperature-induced mechanical properties of polymer. Nanoindenter XP(MTS) was used to measure thermo mechanical properties of PMMA and PC. Polymer was heated by using the heating stage on NanoXP. At CSM(Continuous Stiffness Method) mode test, heating temperature was $110^{\circ}C,120^{\circ}C,130^{\circ}C,140^{\circ}C$ and $150^{\circ}C$ for PMMA, $140^{\circ}C,150^{\circ}C,160^{\circ}C,170^{\circ}C$ and $180^{\circ}C$ for PC, respectively. Maximum indentation depth was 2000nm. At basic mode test, heating temperature was $90^{\circ}C$ and $110^{\circ}C$ for PMMA, $140^{\circ}C,160^{\circ}C$ for PC. Maximum load was 10mN, 20mN and 40mN. Also indented pattern was observed by using SEM and AFM. Mechanical properties of PMMA and PC decreased when temperature increased. Decrease of mechanical properties from PMMA went down rapidly than that of PC.

• Parasites, Hosts and Diseases
• /
• v.52 no.3
• /
• pp.273-280
• /
• 2014

The changing patterns of goblet cell hyperplasia, intestinal epithelial cell turnover, and intestinal motility were studied in ICR and C57BL/6 mice infected with Gymnophalloides seoi (Digenea: Gymnophallidae). Whereas ICR mice retained G. seoi worms until day 7 post-infection (PI), C57BL/6 mice showed a rapid worm expulsion within day 3 PI. Immunosuppression with Depo-Medrol significantly delayed the worm expulsion in C57BL/6 mice. Goblet cell counts were increased in both strains of mice, peaking at day 1 PI in C57BL/6 mice and slowly increasing until day 7 PI in ICR mice. In C57BL/6 mice infected with G. seoi, newly proliferating intestinal epithelial cells were remarkably increased in the crypt, and the increase was the highest at day 1 PI. However, in ICR mice, newly proliferating intestinal epithelial cells increased slowly from day 1 to day 7 PI. Intestinal motility was increased in G. seoi-infected mice, and its chronological pattern was highly correlated with the worm load in both strains of mice. Meanwhile, immunosuppression of C57BL/6 mice abrogated the goblet cell proliferation, reduced the epithelial cell proliferation, and suppressed the intestinal motility. Goblet cell hyperplasia, increased intestinal epithelial cell turnover, and increased intestinal motility should be important mucosal defense mechanisms in G. seoi-infected C57BL/6 mice.