• Journal of Korean Port Research
• /
• v.6 no.2
• /
• pp.43-64
• /
• 1992

This study discusses the interacting with deep water waves approaching from deep water based on the linear wave theory and steep sloping sea bottom floor by the numerical procedure. The results of particular interest are particle velocity and acceleration in x, y, z direction wave height amplification factor reflection coefficient and dimensionless pressure distribution on the steep sloping bottom with respect to the various incident wave angle. The wave loads relative to various bottom slopes, incident wave angles and wave periods on submerged breakwater and pipe are represented in comparison with mild sloping bottom the wave load parameters on the steep sloping bottom seemed to be influenced by variation of incident wave angle. In general the particle velocities and accelerations in x, y, z directions on the steep sloping bottom represented larger value or about two than those on the mild sloping bottom according to incident wave angle. However, the wave height amplification factors did not show distinct difference, but the slight variation with respect to the various incident angle showed on mild sloping bottom. The reflection coefficient increased with respect to increase of the incident angle on the steep sloping bottom the results also indicate that the very steep sloping beach produces a rather substantial amount of reflection as we expected. No significant variation of wave pressure was shown on the steep sloping bottom but it represented a certain amount of variation on the mild sloping bottom according to the various incident wave angle. The analysis at the OTEC site also showed similar results.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.57-64
• /
• 1997

The process design of backward and forward extrusion of axisymmetric part has been studied in this paper. The important factors of cold forging process with complex geometry are the design of initial billet shape, the possibility of forming by one-stage operation and the determination of preform shapes, etc. Based on the systematic procedure of process sequence design, the forming operation of cold forged part is analyzed by the commercial finite element program, DEFORM. The design criteria are forming load, geo- metrical filling without defect and a sound distribution of effective strain in final product. It is noted that one step of preform operation is required to obtain the final product. Numerical result is compared with experi- mental one. It is found that the analyzed result is in good agreement with actual forming result.

• Structural Engineering and Mechanics
• /
• v.91 no.3
• /
• pp.251-262
• /
• 2024

Numerical modeling using the finite element method (FEM) offers crucial insights into the mechanical behavior of prostheses, including stress and strain distribution, load transfer, and stress intensity factors. Analyzing cracking in PMMA surgical cement (polymethylmethacrylate) for total hip prostheses (THP) is essential for understanding the loosening phenomenon, as the rupture of orthopedic cement is a primary cause. By understanding various failure mechanisms, significant advancements in cemented total prostheses can be achieved. This study performed a numerical analysis using a 3D FEM model to evaluate stress levels in different THP models, aiming to model damage in the orthopedic cement used in total hip arthroplasty. Utilizing ABAQUS software, FEM, and XFEM, the damage in three types of THPs-Charnley (CMK3), Osteal (BM3), and THOMPSON was modeled under stumbling loading conditions. XFEM allowed for the consideration of crack propagation between the cement and bone, while the GEARING criterion employed a user-defined field subroutine to model damage parameters. The study's findings can contribute to improving implant fixation techniques and preventing postoperative complications in orthopedic surgery.

• Journal of Aerospace System Engineering
• /
• v.18 no.4
• /
• pp.61-69
• /
• 2024

With increasing interest in aviation leisure sports, the demand for ultralight aircraft has increased, highlighting the necessity for robust structural design of the aircraft. In response, this study conducted static structural analysis and free-fall analysis of fuselage frame of ultralight aircraft. Robust design and crashworthiness under operational load conditions and vertical impact scenarios were evaluated by assessing maximum stress and safety factors. Analyses were performed using finite element method-based software ANSYS Workbench. Results including stress distribution and strain were analyzed to verify the safety of the designed fuselage frame. Additionally, this study predicted excessive deformation and failure locations of the fuselage frame during vertical drop impacts.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.1
• /
• pp.235-243
• /
• 2008

The purpose of this study is to find out the effect of Growth Hormone promotin and kinetic factors on Growth Hormone Activated Shoes. The results of the present study were as follows; First, there was a significient difference between a normal shoes and the Growth Hormone activated shoes in the student's GH secretion with running test, and there was a significant interaction effect between shoes and distance. therefore it can be assumed that there is a significant effect of GH secretion in student at growth period during running with Growth Hormine Activated Shoes. Second, Within 4km walking, Growth Hormone secretion was in creased averagely in student. Third, Growth Hormone Activated Shoes make a large load for light motion as walking. For heavy motion as running, it make a large impulsion but good pressure distribution and small loading rate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2037-2047
• /
• 1991

Strength is not simply a single given value but rather is a statistical one with certain distribution functions. This is because it is affected by many unknown factors such as size, shape, stress distribution, and combined stresses. In this study, a model of loss probability is proposed in view of the fact that one of the fundamental configuration of nature is hexagonal, for example, the shapes of lattice unit, grain, and so on. The model sues the concept of loss of certain element in place of Jayatilaka-Trustrum's length and angle of cracks. Using this model, the loss probability due to each loss of certain elements is obtained. Then, the maximum principal stress is calculated by the finite element method at the centroid of the elements under the tensile load for the 4,095 models of analysis. Finally, the failure probability of the brittle materials is obtained by multiplying the loss probability by the ratio of the maximum principal stress to theoretical tensile strength. Comparison of the result of the Jayatilaka-Trustrum's model and the proposed model shows that the failure probabilities by the two methods are in good agreement. Further, it is shown that the parametric relationship of semi-crack lengths for various degrees of birittleness can be determined. Therefore, the analysis of the failure probability suing the proposed model is shown to be promising as a new method for the study of the failure probability of birttle materials.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.4
• /
• pp.210-220
• /
• 2002

We analysised the effect of harmonics on electric machines of substation power system barred on quantitatively measured harmonics and proposed the methods for prevention of harmonics through checking on transformer, rectifier and cable's capacities against harmonics with reference to KEPCO's electricity service standard. In order to analysis harmoninics of silicon rectifier that is power source in DC substation, computer simulations for a substation with TR of high voltage distribution switchboard are performed. Simulation results show that the total harmonic distortion factor becomes smaller for TR primary and receiving points in order rather than silicon rectifier which is harmonic generation source so that the harmonics generated frets each rectifier are outflowed to power supply and high voltage distribution switchboard The result of higher distortion factors of voltage and current for rectifier with 100% load than those with 50 % and 30% indicates that the waveform of voltage and current for the real substation power system at the office-going and the closing hours with heavy loads might be more distorted. As proposed methods for harmonic reduction, the conventional 6 pulse-type for substation is required to be replaced by 12 pulse-type for reduction of 5th and 7th harmonics. The active filter rather than the passive filter is more effective due to severe variance of rectifier loads, but the high cost is price to be paid. In view of installation area and costs, the use of 12 pulse-type transformer is desirable and then the parallel transformer and the rectifier within the substation must be replaced at the same time. Other substations with parallel feeder can use 6 pulse-type transformer.

• Journal of Korea Water Resources Association
• /
• v.35 no.6
• /
• pp.753-762
• /
• 2002

In-stream vegetation is an essential element of a stream channel. Vegetation plays an important role in flood control and the natural environment in stream channels. This research investigates the relationship between in-stream vegetation and stream changes. This study investigates the distribution characteristic of vegetation in some rivers of Korea. Although there are many physical factors that cause changes to streams, this research verified that in-stream vegetation caused sediment deposition. A hydraulic model experiment was conducted. Tests were conducted in a simulated gravel bed stream (bed slope 1/200) with Phragmites japonica. The average diameter of the bed load used was 0.3 mm and 27 kg were uniformly supplied for 1 hour under same hydraulic conditions. The deposition and scouring as well as the change of flow differed according to the density and arrangement of the Phragmites japonica. In-stream vegetation and stream channel change are closely related because deposition and scouring affects the distribution of vegetation.

• Journal of Korea Multimedia Society
• /
• v.7 no.5
• /
• pp.737-743
• /
• 2004

In this paper, we propose the call control scheme that can improve the capacity of the wireless system for the non-uniform traffic load distribution and the multiple types of services in multiple cells CDMA system. The number of mobile stations that can be served simultaneously in a base station is limited by the amount of total interference received in CDMA system. Further, the average number of mobile stations in each cell may not be uniformly distributed. Considering this factors, the call admission control scheme using the effective bandwidth concept is adapted in this paper. Thus, the bandwidth for a new call can be varied dynamically for reducing the blocking rate of new calls and the dropping rate of handoff calls. The suggested call control scheme is experimented through a simulation by dynamically assigning the bandwidth to new and handoff calls. The simulation results show that the proposed call control scheme can accommodate more mobile stations than the other methods in multiple cells environment.

• Journal of Biomedical Engineering Research
• /
• v.24 no.4
• /
• pp.363-367
• /
• 2003

Contact area and pressure are important factors which directly influence a life of knee implants. Since implant's mechanical functions should be experimentally evaluated for clinical use, many studies using a knee simulator and a pressure sensor system have been conducted. However it has not been reported that the contact pressure's distribution of a knee implant motion was estimated in real-time during a gate cycle. Therefore. the objective of this study was to analyze the contact pressure distribution for the motion of a joint using the knee simulator and I-scan sensor system. For this purpose, we developed a force-controlled dynamic knee simulator to evaluate the mechanical performance of artificial knee joint. This simulator includes a function of a soft tissue and has a 4-degree-of-freedom to represent an axial compressive load and a flexion angle. As axial compressive force and a flexion angle of the femoral component can be controlled by PC program. The pressure is also measured from I-scan system and simulator to visualize the pressure distribution on the joint contact surfaces under loading condition during walking cycle. The compressive loading curve was the major cause for the contact pressure distribution and its center move in a cycle as to a flexion angie. In conclusion, this system can be used to evaluate to the geometric interaction of femoral and tibial design due to a measured mechanical function such as a contact pressure, contact area and a motion of a loading center.