• 한국강구조학회 논문집
• /
• 제18권2호
• /
• pp.225-237
• /
• 2006

김 등(2005a, b)의 연구를 확장시켜 시스템 좌굴 고유치해석법을 이용한 유효좌굴길이 산정법과 2차 탄성해석기법을 이용한 2차모멘트를 이용하여 축력과 휨모멘트를 받는 라멘구조의 보-기둥부재에 대한 개선된 좌굴설계법을 제안한다. 이를 위하여 먼저 국내도로교설계기준, AISC-LRFD, SRC의 각 설계기준에 제시된 내하력 기준식을 이용하여 응력-변형율 관계를 유도하고, 이를 이용한 탄성 및 비탄성 좌굴 고유치해석을 이용한 유효좌굴길이 산정법을 고찰한다. 또한 라멘구조에 대하여 AISC-LRFD에서 제시하고 있는 좌굴 안정성 검토식과 본 연구에서 제시하는 안정성 검토식을 해석예제를 통하여 비교, 검토를 행한다.

• 동력기계공학회지
• /
• 제6권1호
• /
• pp.20-26
• /
• 2002

The purpose of this study is preventing the stick, scuffing, scratch between piston and cylinder in advance, and obtaining data for duration test in actual engine operation. The temperature gradient in cylinder bore according to coolant temperature were measured using $1.5{\ell}$ class diesel engine. 20 thermocouples were installed 2mm deep inside from cylinder wall near top ring of piston in cylinder block, at which points major thermal loads exist. It is suggested as proper measurement points for engine design by industrial engineers. Under full load and $70^{\circ}$, $80^{\circ}C$ and $90^{\circ}C$ coolant temperature conditions, the temperature in cylinder block and engine oil increased gradually according to the increase of coolant temperature, the siamese side temperature of top dead center is $142^{\circ}C$ in peripheral distribution, that is about $20^{\circ}C$ higher than that at thrust, anti-thrust, and rear side temperature, respectively. The maximum pressure of combustion gas in $70^{\circ}C$ coolant temperature is about 2 bar lower than those of $80^{\circ}C$ and $90^{\circ}C$ coolant temperature. The engine torque in $80^{\circ}C$, $90^{\circ}C$ coolant temperature condition is about 4.9Nm higher than that of $70^{\circ}C$ coolant temperature.

• 한국도로학회논문집
• /
• 제18권1호
• /
• pp.63-72
• /
• 2016

PURPOSES : The use of roller-compacted concrete pavement (RCCP) is an environmentally friendly method of construction that utilizes the aggregate interlock effect by means of a hydration reaction and roller compacting, demonstrating a superb structural performance with a relatively small unit water content and unit cement content. However, even if an excellent structural performance was secured through a previous study, the verification research on the environmental load and long-term durability was conducted under unsatisfactory conditions. In order to secure longterm durability, the construction of an appropriate internal air-void structure is required. In this study, a method of improving the long-term durability of RCCP will be suggested by analyzing the internal air-void structure and relevant durability of roller-compacted concrete. METHODS : The method of improving the long-term durability involves measurements of the air content, air voids, and air-spacing factor in RCCP that experiences a change in terms of the kind of air-entraining agent and chemical admixture proportions. This test should be conducted on the basis of test criteria such as ASTM C 457, 672, and KS F 2456. RESULTS : Freezing, thawing, and scaling resistance tests of roller compacted concrete without a chemical admixture showed that it was weak. However, as a result of conducting air entraining (AE) with an AE agent, a large amount of air was distributed with a range of 2~3%, and an air void spacing factor ranging from 200 to $300{\mu}m$ (close to $250{\mu}m$) coming from PCA was secured. Accordingly, the freezing and thawing resistance was improved, with a relative dynamic elastic modulus of more than 80%, and the scaling resistance was improved under the appropriate AE agent content rate. CONCLUSIONS : The long-term durability of RCCP has a direct relationship with the air-void spacing factor, and it can be secured only by ensuring the air void spacing factor through air entraining with the inclusion of an AE agent.

• 토지주택연구
• /
• 제2권4호
• /
• pp.387-395
• /
• 2011

국내 건축구조물의 내진설계기준에 의하면 현장탄성파시험으로 전단파속도를 측정하여 지반을 5종으로 분류하고 이에 의해 건축물에 작용하는 지진하중을 산정하고 있으나 공정상 성토지반에 대해서는 현장탄성파시험을 할 수 없다. 이에 실내에서 간편하게 현장의 상황을 고려하여 전단파속도를 추정할 수 있는 방법을 찾고자 공진주/비틂전단시험과 각종 현장 탄성파 시험결과를 비교 분석하였다. 분석결과 성토체의 구속압을 적절히 고려할 경우 현장탄성파 시험결과와 매우 유사한 결과를 얻을 수 있었다. 또한, 공진주/비틂전단시험에 의해 최대 전단탄성계수와 구속압의 영향평가를 실시한 결과 n값이 0.434~0.561의 일반적 범위의 값을 나타내어 공진주/비틂전단시험으로도 현장지반 전단탄성계수를 유용하게 추정할 수 있는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제32권3호
• /
• pp.101-105
• /
• 2016

Trap effect of groove is evaluated in a lubricating system using computational fluid dynamics (CFD) analysis. The simulation is based on the standard k-ε turbulence model and the discrete phase model (DPM) using a commercial CFD code FLUENT. The simulation results are also capable of showing the particle trajectories in flow field. Computational domain is meshed using the GAMBIT pre-processor. The various grooves are applied in order to improve lubrication characteristics such as reduction of friction loss, increase in load carrying capacity, and trapping of the wear particles. Trap effect of groove is investigated with variations in cross-sectional shape and Reynolds number in this research. Various cross-sectional shapes of groove (rectangular, triangle, U shaped, trapezoid, elliptical shapes) are considered to evaluate the trap effect in simplified two-dimensional sliding bearing. The particles are assumed to steel, and defined a single particle injection condition in various positions. The “reflect” boundary condition for discrete phase is applied to the wall boundary, and the “escape” boundary condition to “pressure inlet” and “pressure outlet” conditions. The streamlines are compared with particles trajectories in the groove. From the results of numerical analysis in the study, it is found that the cross-sectional shapes favorable to the creation of vortex and small eddy current are effective in terms of particle trapping effect. Moreover, it is found that the Reynolds number has a strong influence on the pattern of vortex or small eddy current in the groove, and that the pattern of the vortex or small eddy current affects the trap effect of the groove.

• 한국수자원학회논문집
• /
• 제35권6호
• /
• pp.753-762
• /
• 2002

본 연구에서는 치수안전도의 정확한 평가는 물론 자연환경에 대한 평가에 중요한 하천식물군락에 주목하였다. 특히, 본 연구에서는 하천식물군락과 유사거동에 따른 하도변화와의 상관관계의 규명에 관심을 두었다. 하도수리학 관점에서 하천내 식생분포 특성에 대한 하도현장을 조사한 결과, 하도변화를 야기하는 여러 물리적 요인이 있지만, 하천식생에 의한 하도변화, 특히 하천식물군락에 의한 유사퇴적이 하상변동을 야기시키고 있음이 확인되었다. 이를 수리학적으로 규명하기 위하여 수리모형실험을 실시하였다. 실험에서 하상경사 1/200인 자갈하천에 우점하는 달뿌리풀을 대상으로 하였다. 실험의 내용은 평균입경 0.3 mm의 소류사를 총 1 시간동안 27 kg을 균등하게 공급한 결과, 거의 동일한 수리량 조건하에서 식물군락의 밀도와 배치에 따라 흐름의 변화와 퇴적/세굴양상이 분명히 다르게 나타났다. 따라서, 하도내 퇴적 및 세굴이 하천식물군락의 분포 특성에도 영향을 미치므로 하천식물군락과 유사거동에 따른 하도변화는 상호 밀접한 관계가 있을 것으로 평가할 수 있었다.

• 소성∙가공
• /
• 제24권3호
• /
• pp.205-211
• /
• 2015

The current investigation was performed to study sliding-wear-rate deviation (wear-rate data scatter) in carbon steels with various microstructures. Pure iron, 0.2 wt. % C steel, 0.45 wt. % C steel, and bearing steel (AISI52100) were used for the investigation. These steels possess different microstructures. Microstructures of the pure iron, two carbon steel and the bearing steel were full ferrite, ferrite + pearlite and full pearlite, respectively. Depending on the carbon content, the carbon steel had different pearlite-volume fractions. Dry sliding wear tests of the steel were conducted using a ball-on-disk wear tester at a sliding speed of 0.1 m/s using a bearing ball (AISI52100) as a counterpart. Applied load and sliding distance were 100 N and 300 m, respectively. More than three (up to twelve) tests were conducted for each steel under the same conditions, and the mean deviations in the wear rate of the steel (microstructure) were compared. The wear-rate deviation in the steel with ferrite + pearlite microstructure was higher than that with ferrite microstructure, and the deviation decreased with the increase of pearlite volume fraction. The pure iron and the bearing steel specimens showed much less deviation. The high deviation observed from the ferrite + pearlite steel was attributed to irregular subsurface-crack nucleation and growth at the interface between the two micro constituents (ferrite and pearlite) during the wear test.

• Journal of Welding and Joining
• /
• 제23권6호
• /
• pp.49-54
• /
• 2005

Inner Structured and Bonded(ISB) panel, a kind of metallic sandwich panel, consists of two thin skin plates bonded to a micro-patterned inner structure. Its overall thickness is $1\~3mm$and it has attractive properties such as ultra-lightweight, high efficiency in stiffness-to-weight and strength-to-weight ratio. In many previous studies, resistance welding, brazing and adhesive bonding are studied for joining the panel. However these methods did not consider productivity, but focused on structural characteristics of joined panels, so that the joining process is very complicated and expensive. In this paper, a new joining process with resistance welding is developed. Curved surface electrodes are used to consider the productivity and the stopper is used between electrodes during welding time to maintain the shape of inner structure. Welding time, gap of electrodes and distance between welding points are selected as the process parameters. By measuring the tensile load with respect to the variation of welding time and gap of electrodes, proper welding conditions are studied. Welding time is proper between 1.5-2.5cycle. If welding time is too long, then inner structures are damaged by overheating. Gap of electrode should be shorter than threshold value fur joint strength, when total thickness of inner structure and skin plate is 3.3mm, the threshold distance is 3.0mm.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.1015-1022
• /
• 2001

The objective of this paper is to develop an expert system called NPIES for nuclear piping integrity. This paper describes the structure and the development strategy of the NPIES system. The NPIES system consists of 3 part; the data input part, the analysis part and the output part. The data input part consists of the material properties database module and the suer interface module. The analysis part consists of the LEFM, CDFD, J/T, limit load modules and the 12 analysis routines for different cracks and loading conditions are provided respectively. Analysis results are presented to screen, printer and text file in the output part. Several case studies on circumferentially cracked piping were performed to evaluate the accuracy and the usefulness of the code. Maximum piping loads predicted by the NPIES system agreed well with those by the 3-dimensional finite element analysis. In addition, even if the material properties were not fully given, the NPIES system provided reasonable evaluation results with the predicted material properties inferred from the material properties database module.

• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.787-793
• /
• 2002

In this study, a bar impact test of low velocity was carried out to gain an insight into the damage mechanism and sequence induced in alumina plates(AD 85 and AD 90) under impact conditions. An experimental setup utilizing an instrumented long bar impact was devised, that can measure directly the impact force applied to the specimen and supply a compressive contact pressure to the specimen. During the bar impact testing, the influences of the contact pressure applied along the impact direction to the specimen on the fracture behavior were investigated. The measured impact force profiles explained well the damage behavior induced in alumina plates. The higher contact pressure to the specimen led to the less damage due to the suppression of radial cracks due to the increase in the apparent flexural stiffness of plate. It had produced the change of damage pattern developed in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates. The observed results showed the following sequence in damage developed: The development of cone crack at impact region, the formation of radial cracks from the rear surface of plate depending on the plate thickness, the occurrence of crushing within the cone envelope and the fragmentation.