• Journal of the Korean Institute of Gas
• /
• v.26 no.4
• /
• pp.9-17
• /
• 2022

This paper is the continuation of our previous paper, which we refer to as numerical analysis of phase behavior and flow properties in an injection tubing during gas phase CO₂ injection. Our study in this paper show the results during supercritcal CO₂ injection under the same project. Geological CO₂ storage technology is one of the most effective method to decrease climate change due to high injectivity and storage capacity and economics. A demonstration-scale CO₂ storage project was performed in a deep aquifer in the Pohang basin, Korea for a technological development in a large-scale CO₂ storage project. A problem to consider in the early stage design of the project was to analyze CO₂ phase change and flow characteristics during CO₂ injection. To solve this problem, injection conditions were decided by calculating injection rate, pressure, temperature, and thermodynamic properties. For this research, we simulated and numerically analyzed CO₂ phase change from liquid to supercritical phase and flow characteristics in injection tubing using OLGA program. Our results provide discharge pressure and temperature conditions of CO₂ injection combined with a pressure of an aquifer.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.71-75
• /
• 2010

The efficient performance of absorber is of great importance for the absorption heat pump cycle. The experimental study of absorber with spiral tube of tangential feeding of liquid phase has been investigated using methanol-glycerine as a working fluid. The effect of change in absorber operating conditions was analyzed to improve the performance. The increase in solution flow rate and cooling flow rate positively affects the absorber performance while an increse in the solution concentration negatively affects the absorber performance. The results showed that mass absorption flux was in the range of $0.2{\sim}0.6kgm^{-2}sec^{-1}$, the solution heat transfer coefficient between 1.6 and $4.2kwm^{-2}K^{-1}$, the absorber thermal load from 0.9 to 1.5kw and the mass transfer coefficient from 0.9 to 1.7 m/sec.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.3
• /
• pp.265-270
• /
• 2004

Experiment study on a down scaled two-phase catalytic reactor is presented. As a preliminary step for the development of catalytic reactor, nano-particulate catalyst was prepared. Perovskite La$\_$0.8/Sr$\_$0.2/CoO$_3$is chosen and synthesized as a catalyst considering superior catalytic performance in reduction and oxidation process where oxygen is involved among the reagent. Reactor that has a scale of 2${\times}$10${\times}$25mm was made by machining of A1 block as a layered structure considering further extension to micro-machining. Hydrogen peroxide of 70wt% was adopted as reactant and was provided to the reactor loaded with 1.5 g of catalyst. Reactant flow rate was varied by precision pump with a range of 0.15cc/min to 17.2cc/min. Temperature distribution within reactor was recorded by 3 thermocouples and total amount of liquid product was measured. Temperature distribution and factors that affect temperature were observed and relation between temperature distribution and production rate was also analyzed. Relative time scale plays a significant role in the performance of the reactor. To obtain steady state operation, appropriate ratio of flow rate, catalyst mass and reactor geometry is required and furthermore to get more efficient production rate temperature distribution should be evenly distributed. The database obtained by the experiment will be used as a design parameter for micro reactor.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.2
• /
• pp.190-198
• /
• 2008

In this stduy, the column experiments were carried out assuming the soil was contaminated by leakage of gasoline containing MTBE from USTs and pipes around gas stations. Then, characteristics of MTBE transport in the soil were investigated using CXTFIT program. The column experiments with different soil properties, moisture content, organic matter content and flow rate were carried out. Some parameters(D, R, $\beta$, $\omega$) used in two-site non-equilibrium adsorption model were obtained from measuring the MTBE concentration in injection-liquid and in effluent and using CXTFIT program. In addition, The characteristics of MTBE transport in the soil was found using BTCs and obtained parameters. Consequently, the advection decreased as the increase of the content of fine particle and organic, while the MTBE transport by advection was enhanced as increasing flow rate and moisture content.

• Journal of Energy Engineering
• /
• v.8 no.2
• /
• pp.325-332
• /
• 1999

When a rotating heat pipe is in operation, liquid condensate returns from the condenser to the evaporator along the inside surface by both components of gravitational and centrifugal forces. It was known that its performance was largely dependent on how to increase the flow rates of condensate and keep the condensate film thickness as thin as possible. Most of research works were focussed on this goal, and various inner wall structures such as tapered wall, stepped wall or coil inserted pipe etc. were developed. In the present study, a stepped wall structure with 3 internal grooves in the condenser and adiabatic zone was examined. For this system, the condensate would flow down to the evaporator through the grooves, resulting a reduced film thickness over the condenser surface. Experimental data showed an enhancement of heat transfer coefficient in the condenser zone. An analytical solution to the condensate film thickness showed that the analytically calculated values of heat transfer coefficient were considerably higher than the experimental data.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.16 no.1
• /
• pp.46-52
• /
• 2008

Oils and chlorinated solvents leaking to the subsurface are entrapped in the soil pore and these are called as nonaqueous phase liquids (NAPL). NAPL entrapped in porous media acts as a continuous source for surface and ground water contamination. This study visualized dissolution of trichloroethylene (TCE) entrapped in porous media and quantified the velocity of TCE dissolution using an image analysis technique. As the water velocity increased, the level of dissolution increased. The results imply that a TCE contaminated region having a high infiltration rate and groundwater velocity may result in severe groundwater contamination. Microscopic images of TCE entrapped in porous media showed that TCE present in the preferential flow paths was easily dissoluted into the water phase. However, TCE present in the stagnant flow region was visualized for long time. The results imply that TCE would be still present in the soil if TCE is detected in goundwater.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.5
• /
• pp.407-414
• /
• 2001

In this study, the absorption kinetics of $CO_2$onto a mixture of AMP (2-amino-2-methyl-1-propanol) MEA (monoethanolamine) water were investigated at 30 and 4$0^{\circ}C$ using a packed absorption tower. Solubility and absorption rate of $CO_2$into alkanolamine solutions and optimal condition of $CO_2$absorption process were investigated. The experimental conditions are as follows; temperature of 30 and 4$0^{\circ}C$, gas flow rate of 3ι/min for the absorption tower, and liquid flow rate of 0.1ι/min. Feed gas was a mixture of 85% $N_2$and 15% $CO_2$. The experimental results showed that AMP had greater solubilities and faster absorption rates than MEA and DEA. In addition, MEA had the fastest initial reaction rate. To improve the properties of AMP which have low initial reaction rate and high cost, AMP was used with MEA. The mixing ratio was also changed in constant total molarity of 1,2,3 and 4. The experimental results can be summarized as follows: (1) in solubility experiment, the addition of MEA in constant total polarity decreased the solubility of $CO_2$in AMP/MEA mixture. (2) from 0 to about 0.3 in mixing ratio, the solubility of $CO_2$in AMP/MEA mixture had little differences compared with the sum of solubility of AMP only and solubility of MEA only . (3) mixing ratio of 0.3 was found to be an optimal point with the fastest $CO_2$absorption rate.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.3 no.2
• /
• pp.18-24
• /
• 2000

A two-dimensional numerical method for inviscid two-fluid flows with a significant entrainment into both directions is established, and the oil leakage from a non-pressurized underwater pipe is studied. The interface between two fluids is modeled at a vortex sheet. The flow field and the subsequent interface evolution are solved by using the vortex-in-cell method. For longer flow simulation with a realistic two fluids interaction, an efficient merging scheme is introduced. In the Boussinesq limit, the speed of the external fluid intrusion into the pipe is very close to the existing mathematical models, and the lock exchange is observed in spite of a significant roll-up of the interface and entrainments. It is believed that the developed method can be utilized effectively for further detailed studies on various two-fluid flows which are encountered in many different marine oil spill problems.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.1
• /
• pp.73-79
• /
• 2010

Propellant tank pressurizing gas injector is used in the pressurization system of liquid propellant rocket to reduce incoming gas velocity and distribute the gas in the tank. Temperature distribution in the propellant tank ullage is varied according to the gas injector shape, and it has influence on the required pressurant gas and thermal phenomena in the tank. In this paper, diffuser type gas injector was studied to make the ullage have stratified temperature distribution. Injected gas flow at the outlet of prototype diffuser was visulized using particle image velocimetry method and it was compared with the results of calculation. Calculation was well agreed with measurement and was used as an inlet condition of propellant tank ullage calculation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.2
• /
• pp.143-148
• /
• 2007

An impulse turbine, which is a main component of a liquid rocket engine, needs to be a small size with light weight and generate large power. Since the impulse turbine is being operated under complicated supersonic conditions, flow analysis and performance prediction largely depend on CFD technique. In order to increase the reliability of the prediction code, however, it often requires an experimental data to compare. In this research a rotating turbine rotor with multiple blades is simulated with a two-dimensional stationary cascade to check the effect of major flow parameters. Mach number is measured at nozzle exit by using a pitot tube and the blade thrust was also measured with a load cell. The measured thrust coefficient and the power are compared well with the designed conditions, which proves the design procedures are properly taken.