• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.984-990
• /
• 2017

Mesh screen modeling and liquid propellant discharge simulation of surface tension tank were performed using commercial CFD software Flow-3d. $350{\times}2600$, $400{\times}3000$ and $510{\times}3600$ DTW mesh screen were modeled using macroscopic porous media model. Porosity, capillary pressure, and drag coefficient were assigned for each mesh screen model, and bubble point simulations were performed. The mesh screen model was validated with the experimental data. Based on the screen modeling, liquid propellant discharge simulation from PMD tank was performed. NTO was assigned as the liquid propellant, and void was set to flow into the tank inlet to achieve an initial volume flow rate of liquid propellant in $3{\times}10^{-3}g$ acceleration condition. The intial flow pressure drop through the mesh screen was approximately 270 Pa, and the pressure drop increased with time. Liquid propellant discharge was sustained until the flow pressure drop reached approximately 630 Pa, which was near the estimated bubble point value of the screen model.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.105-109
• /
• 2002

The short-term AC breakdown strength of laminated polypropylene insulating Paper (PPLP) has been studied for cold dielectric of high temperature superconductivity power cables. The design and operating conditions of the electrode system for studying of short-term breakdown strength of one-layer and multi-layer PPLP samples are discussed in liquid nitrogen(LN2) state. The influence of various operating factors (geometry and dimension of electrodes, speed of tested voltage, thickness of test sample) on the value of short-term AC breakdown strength at cryogenic temperature has been established.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.145-152
• /
• 2010

The gel polymer electrolyte(GPE) were prepared by in-situ thermal cross-linking reaction of homogeneous precursor solution of perfluorinated phosphate-based cross-linker and liquid electrolyte. Ionic conductivities and electrochemical properties of the prepared gel polymer electrolyte with the various contents of liquid electrolytes and perfluorinated organophosphate-based cross-linker were examined. The stable gel polymer electrolyte was obtained up to 97 wt% of the liquid electrolyte. Ionic conductivity and electrochemical properties of the gel polymer electrolytes with the various chain length of perfluorinated ethylene oxide and different content of liquid electrolytes were examined. The maximum ionic conductivity of liquid electrolyte was measured to be $1.02\;{\times}\;10^{-2}\;S/cm$ at $30^{\circ}C$ using the cross-linker($PFT_nGA$). The electrochemical stability of the gel polymer electrolyte was extended to 4.5 V. The electrochemical performances of test cells composed of the resulting gel polymer electrolyte were also studied to evaluate the applicability on the lithium polymer batteries. The test cell carried a discharge capacity of 136.11mAh/g at 0.1C. The discharge capacity was measured to be 91% at 2C rate. The discharge capacity decreased with increase of discharge rate which was due to the polarization. After 500th charge/discharge cycles, the capacity of battery decreased to be 70% of the initial capacity.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.9-12
• /
• 2010

This paper discusses experimental data for the assessment of flow discharging characteristics of double swirl coaxial injectors operating at fuel-rich conditions. Combustion tests employing liquid oxygen and kerosene (Jet A-1) were conducted and a discharge coefficient was utilized for defining flow characteristics. A mass flow rate, a pressure, and a temperature were measured to estimate discharge coefficients. Fuel injectors revealed a fixed value of a discharge coefficient regardless of matched LOx injector design, chamber pressure, and mixture ratio. However, oxidizer injectors showed varying discharging coefficients depending on chamber pressure and mixture ratio. Flame structure variations seem to affect flow discharging characteristics of the oxidizer side.

• Journal of Animal Environmental Science
• /
• v.7 no.1
• /
• pp.1-12
• /
• 2001

This study was conducted to develope an automatic liquid feeder for early weaning piglets and to test the efficacy of the system. The liquid feeder consists of water heating and discharge unit, dry diet storing and discharge unit, mixing and discharge unit, mixed liquid feed-delivering unit, and the central control part which control each unit, feeding frequency and the amount of feeding. For investigating the possibility of practical use, a feeding trial was carried out using eighteen three way crossbred piglets weaned on 19 days of age for the experimental period of six weeks. Experimental diet was provided in liquid form using the automatic liquid feeder for the first three weeks and in dry form for the later three weeks. The water heating and discharge unit exactly supplied warm water by 27 $m\ell$/s, into the mixing unit. The dry diet storing and discharge unit supplied dry feed by 3.7g/s, into the mixing unit. Being compared with the standard growth rate suggested by NRC, average daily gain of the piglets during the first three weeks of liquid feeding was lower by 10%, while it was higher during three weeks of dry feeding and over the whole experimental period by 24 and 17%, respectively. Feed/gain was 1.09, 2.14 and 1.89 for the first 3 weeks, later 3 weeks, and whole period, respectively. Diarrhea was observed for three days from day 3 to day 7 after feeding liquid diet, but no pig died of it. In conclusion, a preliminary test for the newly developed an automatic liquid feeder using 19 days of age weaning piglets showed that the unit was successfully operated without any major problems. Piglets raised on a liquid diet through the unit developed grew less during the first three weeks, but their growth and feed intake were greatly improved thereafter, indicating the developed automatic liquid feeder may be practically used in swine industry.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.58-63
• /
• 1996

A study is drawn up its result's tables and graphs by measuring tools(outside micrometer cylinder gauge and dial caliper gauge) on the difference of diameter volumes from before-discharge and after-discharge under 52 Kind's experimental condition by cupper and graphite electrode of CNC EDM. The EDM is attached with A.V.R. and memory scope for keep up accuracy and the fixed table of work piece is used in order to eliminate the noise by the internal resistance of it and forcing to eradicate the discharge liquid. It is analyzed cutting conditions to compare its wave value and pulse time.(Ton Toff) through voltage and current for decreasing working error.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.1
• /
• pp.66-71
• /
• 2016

In this study, electrical and spectroscopic characteristics were investigated in the pin to plate discharge of 0.9% weight per unit volume saline solution. The positive and positive- and negative-going dc pulse with 5% duty ratio were applied to tungsten pin electrode. The more amount of discharge current flew in negative discharge. The temperature, which is considered as a local value in the vicinity of vapor of discharge, was about 3,000K which is much higher than the value recommended to be controlled. It can be suggested that not only the temperature of liquid but also the local temperature of vapor is monitored to investigate damages on tissue or cells in biological application.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.1
• /
• pp.8-13
• /
• 2011

Interfacial compatibility between the Si-Cu electrode and diluted ionic liquid electrolyte containing 50 vol.% of 1M lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)/1-methyl-1-propylpyrrolidinium bis(trifluoromethylsulfonyl)imide (MPP-TFSI) and 50 vol.% dimethyl carbonate (DMC) in a lithium cell and dilution effect on surface chemistry are examined. ex-situ ATR FTIR analysis results reveal that the surface of the Si-Cu electrode cycled in the diluted ionic liquid electrolyte is effectively passivated with the SEI layer mainly composed of carboxylate salts-containing polymeric compounds produced by the decomposition of DMC. Surface species by the decomposition of TFSI anion and MPP cation are found to be relatively in a very low concentration level. Passivation of electrode surface with the SEI species contributes to protect from further interfacial reactions and to preserve the electrode structure over 200 cycles, delivering discharge capacity of > 1670 $mAhg^{-1}$ and capacity retention of 88% of maximum discharge capacity.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.05a
• /
• pp.425.1-425
• /
• 2001

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.17-19
• /
• 2009

The voltage and frequency dependence of voltage holding ratio (VHR) in a homogeneously-aligned liquid-crystal (LC) cell is studied in this paper. The discharge curves with different scan frequencies are obtained and the saturation phenomenon of VHR is observed under specific amplitudes of driving voltage. Our results suggest a reasonable concept to improve the VHR in LC displays without increasing the frame rate.