• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.91-96
• /
• 2020

The 33-mode dielectric and piezoelectric properties of Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 piezoelectric single crystals were measured under large electric field and compressive stress. The phase transition from the low temperature rhombohedral to the high temperature tetragonal structure was observed in the range of 110~140℃, and the Curie temperature changing to the cubic structure was about 165℃. The polarization change according to the compressive stress and electric field was measured. Relative dielectric constant was calculated from the slope of the polarization curve applied to the electric field, and the calculated relative dielectric constant increased as the applied stress increased, and the relative dielectric constant decreased as the applied electric field increased. The strain according to the compressive stress and electric field change was measured, the piezoelectric constant was calculated from the slope of the curve, and the phase transition according to the application of pressure was confirmed. In the case of practical application as an underwater or medical ultrasonic actuator, it is necessary to properly design the magnitude of the compressive stress applied to the device and the DC bias in order to maintain linear driving.

• Corrosion Science and Technology
• /
• v.12 no.1
• /
• pp.40-49
• /
• 2013

Effects of magnesium and pH on corrosion of aluminum galvanically coupled to iron have studied by using potentio- dynamic and static tests for polarization curves, Mott-Schottky test for analysis of semiconductor property, and GD-AES and XPS for film analysis. Pitting potential was sensitive to magnesium as an alloying element but not to pH, while passive current was sensitive to pH but not to magnesium. It was explained with, instead of point defect model (PDM), surface charge model describing that the ingression of chloride depends on the state of surface charge and passive film at film/solution interface is affected by pH. In addition, galvanic current of aluminum electrically coupled to iron was not affected by magnesium in pH 8.4, 0.2M citrate solution but was increased by magnesium at the solution of pH 9.1. The galvanic current at pH 9.1 increased with time at the initial stage and after the exposure of about 200 minute, decreased and stabilized. The behavior of the galvanic current was related with the concentration of magnesium at the surface. It agreed with the depletion of magnesium at the oxide surface by using glow discharge atomic emission spectroscopy (GD-AES). In addition, pitting potential of pure aluminum was reduced in neutral pH solution where chloride ion maybe are competitively adsorbed on pure aluminum. It was confirmed by the exponential decrease of pitting potential with log of [$Cl^-$] around 0.025 M of [$Cl^-$] and linear decrease of the pitting potential. From the above results, unlike magnesium, alloying elements with higher electron negativity, lowering isoelectric point (ISE), are recommended to be added to improve pitting corrosion resistance of aluminum and its alloys in neutral solutions as well as their galvanic corrosion resistance in weakly basic solutions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.6
• /
• pp.513-518
• /
• 2015

Salinity gradient power (SGP) has attracted significant attention because of its high potential. In this study, we evaluate reverse electrodialysis (RED) with various compositions of available resources. The polarization curve (I-V characteristics) shows linear behavior, and therefore the power density curve has a parabolic shape. We measure the power density with varying compartment thicknesses and inlet flow rates. The gross power density increases with decreasing compartment thickness and increasing flow rate. The net power density, which is the gross power density minus the pumping power, has a maximum value at a compartment thickness of 0.2 mm and an inlet flow rate of 22.5 mL/min. The power density in RED is also evaluated with compositions of desalination brines, seawater, river water, wastewater, and brackish water. A maximum power density of $1.75W/m^2$ is obtained when brine discharged from forward osmosis (FO) and river water are used as the concentrated and the diluted solutions, respectively.

• Journal of the Korea Concrete Institute
• /
• v.21 no.4
• /
• pp.409-417
• /
• 2009

In this study, autogenous crack healing and artificial crack healing using electrochemical electro deposition method were conducted to compare in the aspects of corrosion monitoring. Furthermore, the analysis of impressed voltage characteristics, galvanic current and linear polarization resistance comparison, and photo image processing technique were performed for quantitative comparisons of healing ratio. As a result, it was found that, in view of impressed voltage of artificial crack healing, the measured voltage was increased as time goes by. From the galvanic test results of artificial crack healing, the current vs. potential distribution value were formed widely in comparison with autogenous crack healing. In this point, it was shown that artificial crack healing has more eleatic resistance capacity than autogenous crack healing technique. Finally, it was found that artificial crack healing was 1.63 times higher than autogenous healing in view of crack healing ratio.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.6
• /
• pp.33-41
• /
• 2004

In this paper, a polarimetric fiber optic current sensor(P-FOCS) is experimented and fabricated, and then a possibility to the commercial utilization of the P-FOCS is also investigated. The P-FOCS measures an applied current by a Faraday rotation linearly proportional to a magnetic field generated by the applied current. The bending-induced linear birefringence in the sensing fiber is minimized by using the low birefringent fiber. Also, all fiber-optic components are used to avoid optical losses coming from the use of bulk components. A signal processing circuit is constructed and used to eliminate the effects of intensity variations in the output signal due to losses coming from misalignments of components such as fiber connectors. Using the optical source of 632.8nm wavelength, Faraday rotation is measured by passing through the sensing fiber within the solenoid of about 1500 turns which is equivalent to a current source of about 7500A. In the range of 1000A to 7500A, the measurement error for linearity is within about 1.5%.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.3
• /
• pp.202-209
• /
• 2014

In this paper, we analyzed the effects by multi-stacking superstrates over the circular-polarized patch antenna. The previous works considered a single-layered superstrate or a superstrate with multiple layers, and did not almost consider the axial ratio at the performance analysis. First, the effect of center frequency shift is analyzed by the variation of air-gap height between patch antenna and superstrate. The center frequency is down-shifted at the smaller air-gap height and has almost the same frequency as patch antenna at the air-gap height of $005{\lambda}_0$. Second, the antenna performance is analyzed by multi-stacking superstrates with the air-gap height of $005{\lambda}_0$. As the number of multi-stacked superstrates increase, antenna gain has a linear increase and axial ratio is exponentially deteriorated. In addition, it has also been observed that the antenna performance has the same trend with the number of multi-stacked superstrates as the thickness of superstrate increases. Finally, we confirmed that it is possible to design the CP patch antenna with the scalable gain and less than 3dB axial ratio by stacking the superstrate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.8
• /
• pp.766-773
• /
• 2016

This paper proposes an aircraft-installed compact offset-parabolic-reflector antenna for the spinning direction-finding applications. The feeder of the reflector antenna is a LPDA antenna that has the ultra-wideband characteristics and the $45^{\circ}$ slant linear polarization. The reflector is designed to be slanted by $5^{\circ}$ in the elevation and to be small in size on the basis of the reference parabolic shape for the purpose of the high gain and mounting on the underside of aircraft fuselage. Over the ultra-wideband 20:1 bandwidth from S to Ka band, the measured average gain of the proposed antenna is 27.97 dBi, and the average half-power beam width is $4.55^{\circ}$ in the azimuth and $4.3^{\circ}$ in the elevation which is the pencil-beam radiation pattern. All the measured data are similar to the simulation results. The designed compact offset-parabolic-reflector antenna that is installed in the limited area has the ultra-wideband and high-gain characteristics. We expect that the newly designed antenna can be applied to the spinning direction-finding antenna system installed in an aircraft.

• Journal of the Korean Chemical Society
• /
• v.21 no.4
• /
• pp.276-283
• /
• 1977

Reduction of dichromate at a platinum cathode in acid solution was studied by cyclic voltammetry and controlled potential electrolysis. Cathodic polarization curve consisted of three waves in unbuffered solution of potassium dichromate having initial pH ranges 1.5∼4.0, with sodium sulfate as the supporting electrolyte. Relative heights of the first and the second waves were, respectively, a function of chromium (Ⅵ) concentration and activity of hydrogen ion, but that of the third wave was not proportional to both of them. The current of the first two peaks were proportional to the sweep rate of potential (${\nu}$), while that of the last peak vs. ${\nu}^{1/2}$ was linear at the sweep rate of less than 50mV/sec. By the controlled potential electrolysis, the reduction of chromium (Ⅵ) was almost completely suppressed at potentials more negative than the last peak and at initial pH's above ca. 2.3 of unbuffered solution. Therefore, these peaks represented, respectively, $Cr_2O_7^{2-}{\to}Cr^{3+},\;2H^+{\to}H_2$ and the formation of a cathodic film.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.661-667
• /
• 2008

In this study, cholesteric liquid crystal (CLC) was synthesized and applied as a polarizing component on the optical film of back light units (BLU) for LCDs. After mixing CLC with nematic liquid crystal, this mixture was fulfilled in the module consisting of two films and then its amplifying efficiency and polarizing ability for a planarly emitted light were examined to apply as a BLU polarizer film for increasing the brightness of light. The properties of CLC compound were tested by UV/Visible spectroscopy and polarizing optical microscopy (POM). Flexible spacer was made by linear carboxylic acid group of cholesteric derivatives between cholesterol mesogen units for one-axis orientation in each layer. The CLC containing film could be used as a module to increase the ability of polarization and to enhance brightness of BLU and to widen wavelength range by stacking the films.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.542-548
• /
• 2001

A robust, accurate, broad-band, alternating current sensor using fiber-optics is being developed as a part of optical over current protection relay system. The sensor uses the Faraday effect in optical fiber and polarimetric measurements tc sense electrical current. The current sensing coil consists of a length of twisted optical fiber and Faraday rotator mirror to suppress the linear birefringence effect. Due to its single-ended closed path structure, it can not only be easily installed to the target with great isolation from other fields in the vicinity, but the sensitivity can be increased by using multiple turns. This paper reports on the theoretical backgrounds of the sensor design and the preliminary experimental results.