• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.943-944
• /
• 2007

In this paper, the development and the test of 13.2kV/630A high-Tc superconducting fault current limiting coil are described. The fault current limiting coil made of Coated Conductor (CC) was fabricated with bifilar winding method for non-inductive characteristics and tested in the distribution power system level in Dec. 2006. In order to determine the length of the superconducting coil, applied voltage per unit length(V/m) was studied analytically and it was verified through experiments. For the volume minimization, the coil was designed with concentrical arrangement method. The short-circuit test was performed with the prospective fault current of asymmetrical 10kA whose maximum fault current was $30kA_{peak}$. In the test, the voltage drop and the current of the coil were measured and the resistance of the coil was obtained. Also, the temperature rise of the coil was calculated with the relationship between the resistance and the temperature of CC. In this paper, the experimental results are analyzed and compared with the simulation.

• The Korean Journal of Ecology
• /
• v.8 no.2
• /
• pp.89-98
• /
• 1985

Correlations between horizontal distributions of bamboos (Bambusaceae) in the Korean peninsula and environmental factors were studied using taxanomic and geographical literatures, both old and current. The vertical distributions of bamboos on Mt. Chiri were also studied, and environmental factors limiting horizontal and vertical distributions were compared. There are 18 species of bamboos (belonging to 5 genera) distributed in the Korean peninsula. The distributional range of each genus were distinct, although overlapped. Northern limit of bamboos of any species was marked by the line connecting Paikryung Island (124。40'E, 38。00'N), Mt. Changsoo, Mt. Myungji, Mt. Myohyung and Myungchum (129。40'E, 41。10'N). The optimum range of bamboos was concluded to be restricted to several southern province, with annual precipitation over 1,200 mm. The limiting factors on the distribution were inferred to be low temperature and duration of it. Mean daily minimum temperature of January and the number of days with daily mean temperatures below zero during January showed close associations with the distributional range, and an environmental factors favouring the distributrion of bamboos appeared to be vicinity of warm sea current, deep and extended snow acculation and southern exposure. The vertical distribution of bamboos on Mt. Chiri was limited by low temperature, unfavorable topographic and edaphic conditions caused by steep slope. Difference in the vertical limits between SE and NW slopes are caused by the differences in temperature and precipitation between the slopes. Bamboos were more abundant in valleys than on the ridge, apparently because the deeper snow in the valleys protected the plants from low temperature, heavy winter winds and desiccation.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.3
• /
• pp.94-101
• /
• 1985

The flame temperature of LPG-air premixture flame was measured by extrapolation of limiting case corresponding to the infinitely thin diameter of Platinum-resistance-hot-wire. LPG-air premixture flame, initially under atmospheric pressure and room temperature, propagates downward from top of the model combustion chamber maintained at constant pressure through the whole combustion process. Analytical calculation technique was also applied to determine full temperature history or spatial temperature distribution from flame reaction zone to burnt gas region.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.9
• /
• pp.584-589
• /
• 2000

We fabricated resistive superconducting fault current limiters (SFCL) based on YBCO thin films grown on a 2-inch diameter Al2O3 substrate. The current limiting element was 1 mm wide and 260mm long meander line prepared by standard photolithography. The minimum quench current of the current limiting element was about 8 Apeak. This SFCL sucessfully controlled the fault current below 14.3 Apeak at the voltage of 100 Apeak which is otherwise to increase up to 141 Apeak. The quench completion time was less than 3 msec. The temperature of the current limiting element rose to about 200 K in 3 cycles after fault. The SFCL showed reproducible quench during hundreds times of repeated experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.5
• /
• pp.53-59
• /
• 1996

Warm deep drawing of single-action dies using local heating has appeared to be an alternative attractive production method of multi-operation die sets generally used at room temperature in deep drawing of rectangular cup. Uniaxial tensile tests and deep drawing tests of various materials are carried out and the effect of temperature on tensile properties and drawability are examined at temperatures up to 200 .deg. C under three kinds of lubricants of teflon film, vinyl film and drawing oil. Good formability is achieved when punch and die temperature were differentiated intentionally in order to get large tensile strength(TS) at punch shoulder protion and small TS at die side. Throughout the experiments, it has been shown that the limiting drawing height of STS316L was increased with heating die and blank holder at 100 .deg. C, but that of STS430 wasn't. When vinyl or teflon film was attached on the plates, the drawability was increased considerably.

• Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.10-17
• /
• 2003

For limitation and interruption of short circuit currents from low voltage to extra high voltage applications, the electrical equipment including fuses and circuit breakers, are widely used today. But in order to anticipate increasing needs for effective and competitive device for limiting the growing fault current in electrical power systems, fault current limitation technologies and fault current limitation devices are widely introduced and investigated in these days. Furthermore, the applications of high temperature superconducting materials (HTSC) into the current limiting devices are new approach for developing of novel and effective col-rent limitation electrical equipment. In this research, the necessities of current limitation technology and the developed and developing current limitation devices for power systems are introduced. Finally, the investigation of resistive type fault current limiters which is under development by LG and KEPCO were introduced.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.839-846
• /
• 2001

Some deep drawing characteristics at elevated temperatures were investigated for the SCPI steel sheets by using a Cr-coated die. For this investigation, six different temperatures between room temperature and 250$\^{C}$, and six different drawing ratios ranging from 2.4 to 2.9 were considered. As a result, the limiting drawing ratio, the maximum drawing force and the maximum drawing depth were found to be affected sensitively by temperature, and more stable through-thickness strain distribution was observed at elevated temperatures. Some experimental results compared favorably with theoretical results obtained by using the finite element method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.63-70
• /
• 1999

Some deep drawing characteristics to the elevated temperatures were investigated for the SCP1 steel sheets by using the Cr-coated die. For this investigations six steps of temperature ranges from room temperature to 25$0^{\circ}C$ and six kinds of drawing ratio from 2.4 to 2.9 were adopted. As a result the limiting drawing ration maximum drawing force and the maximum drawing depth were sensitively affected by the elevated temperatures and the more stable thickness strain distribution was observed to the elevated temperatures, Some experimental results were compared with analytical results using the DYNA-3D code.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.178-178
• /
• 1999

Low temperature Si epitaxy can provide flexibility for a device designer to tailor or optimize the device performance. It is better method for controlling the doping thickness, concentration and profile than ion implantation and diffusion. But there is a limited growth thickness in this method. At a given temperature, the film grows epitaxially for a certain limiting thickness(hepi) and becomes amorphous. The transition from crystalline Si to amorphous Si is abrupt. In this study, Si film was deposited by ion beam sputter deposition on Si (0001) above a limiting thickness and measure the strain in the interface between crystalline Si and amorphous Si. The strain was compressive and the maximum value was about 2%.

• Transactions of Materials Processing
• /
• v.9 no.2
• /
• pp.186-192
• /
• 2000

Some deep drawing characteristics to the elevated temperatures were investigated for the SCPI steel sheets by using the Cr-coated die. For this investigations, six steps of temperature ranges, from room temperature to 25$0^{\circ}C$, and six kinds of drawing ratio, from 2.4 to 2.9 were adopted. As a result, the limiting drawing ratio, maximum drawing force, and the maximum drawing depth were sensitively affected by the elevated temperatures, and the more stable thickness strain distribution was observed to the elevated temperatures. Some experimental results were compared with analytical results using the DYNA-3D code.