• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.330-332
• /
• 2009

Highly stable bottom gate thin film transistors(TFTs) with a zinc indium tin oxide(Zn-In-Sn-O:ZITO) channel layer have been fabricated by rf-magnetron co-sputtering using a indium tin oxide(ITO:90/10), a tin oxide and a zinc oxide targets. The ZITO TFT (W/L=$40{\mu}m/20{\mu}m$) has a mobility of 24.6 $cm^2$/V.s, a subthreshold swing of 0.12V/dec., a turn-on voltage of -0.4V and an on/off ratio of >$10^9$. When gate field of $1.8{\times}10^5$ V/cm was applied with source-drain current of $3{\mu}A$ at $60^{\circ}C$, the threshold voltage shift was ~0.18 V after 135 hours. We fabricated AM-OLED driven by highly stable bottom gate Zn-In-Sn-O TFT array.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.9-14
• /
• 2005

In this study, we investigated the actual conditions of illumination environment of study rooms in detached houses. From the results, fluorescent lamp as a lighting source and direct lighting method were mainly used. The additional use of local lighting was 48.2[%], and it was not efficient for detailed work. The average illuminance of general lighting and local lighting were 131.41[lx] and 322.57[lx], respectively, and these level were only 54[%] of the lowest illumination standard. This indicates that the lighting levels and the environment are so poor. The satisfaction level of users, however, was relatively high, suggesting insufficient recognition of importancy of lighting for efficient work.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.11-20
• /
• 2011

PSALI is referred to the supplementary lighting for the interior lighting under the daily lighting situation, and pursuant to the pertinent regulations in energy savings design standard and others in recent architecture works, the importance thereof has been increasing gradually coupled with the energy performance index (EPI), energy savings plan and the like as well as expansion of submittal and implementation policies. However, this type of PSALI studies indeed have a number of limitations since it has surrounding environmental conditions in direction, season, region, climate, time, opening rate, window area ratio, actual index, reflection rate of finishing materials and others in the architecture work as well as frequent changes in interior lighting environment for variables in daily light volume flowing into the interior, and others. Therefore, this study has analyzed existing advance research cases to produce the actual-sized model and scaled-down model, and installed the artificial lighting of LED light source possible to reproduce with same capability on both models. As a result of comparison and analysis of the artificial lighting with the key light, it has certain level of error rate from the scaled down lighting device in certain rate and actual model butit was noticeably significant within specific scope.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.7
• /
• pp.1-7
• /
• 2013

LED lamps are appropriate to the light source for use in broadcasting lighting. When the lighting frequency of LED lamp is different from the shutter frequency of camera, however, the flicker appears on the moving image which is taken by the camera under the dimmed light of LED lamp with conventional dimming methods. In this study, a new dimming method for the LED lamps used as the broadcasting lighting is proposed to minimize the flicker. A lighting period in the proposed dimming method is divided into the several sub-periods which have weight of the bits. Also, the proposed dimming method has characteristics that are optimizing the turn-on timings of two LED lamps to reduce the turn-off periods of the lamps and not to overlap the turn-on periods of the lamps. In the experiments, the incidence of the flicker is taken by the camera under several lighting conditions of the conventional dimming methods and the proposed dimming method. In addition, the brightness values of the frames are obtained in the moving image, and incidence of the flicker is evaluated and compared with conventional methods. From the results, the incidence of the flicker in the proposed method is more improved than the conventional methods.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.2
• /
• pp.284-288
• /
• 2015

The color temperature flexibility-typed Lighting Emitting Diode(LED) lighting control system proposed in this thesis employs Pulse Width Modulation(PWM) technique to control the brightness of LED lighting. The LED lighting used as a light source has 20W downlight composed of two types of LED chips: one is Warm White and the other is Cool white. One multi-sensor module consisting an infrared sensor, an illumination sensor, and a temperature sensor was made, to which Bluetooth wireless communication technique was applied to enable a smartphone application to control lighting brightness and identify the information collected from the sensor. CS-1000, a spectroradiometer, was used to measure LED dimming control and the changing values of a color temperature in eight steps. According to a test, it was found that it was possible to change a color temperature from 3187K of Warm White LED to 5600K of Cool White LED.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.3
• /
• pp.255-260
• /
• 2023

In order to spread LED lighting, LED lighting technology directly driven by alternating current (AC) commercial power has recently been introduced. Since current does not flow at a voltage lower than the threshold voltage of the LED, a non-conductive section occurs in the current waveform, and the higher the threshold voltage of the LED, the more discontinuous current waveforms are generated. In this paper, multi-LED modules are connected in series so that the threshold voltage can be adjusted according to the number of LED modules. A small number of LED modules are driven at a low instantaneous rectified voltage, and a large number of LED modules are driven at a high instantaneous rectified voltage to lengthen the overall lighting time of AC-LED lighting, thereby minimizing the luminance deviation of AC-LED lighting. In addition, the load current flowing through the LED module is adjusted to be the same as the design current even at the maximum rectified voltage higher than the design voltage, so that the light brightness of the LED module is kept constant. Therefore, even if the rectified voltage applied to the LED module changes, the AC-LED lighting in which the light brightness is constant and the luminance deviation is minimal has been realized.

• International Journal of Advanced Culture Technology
• /
• v.8 no.1
• /
• pp.207-212
• /
• 2020

The human centric lighting (HCL) control is a major focus point of the smart lighting system design to provide energy efficient and people mood rhythmic motivation lighting in smart buildings. This paper proposes the HCL control using indoor surveillance camera to improve the human motivation and well-beings in the indoor environments like residential and industrial buildings. In this proposed approach, the indoor surveillance camera video streams are used to predict the day lights and occupancy, occupancy specific emotional features predictions using the advanced computer vision techniques, and this human centric features are transmitted to the smart building light management system. The smart building light management system connected with internet of things (IoT) featured lighting devices and controls the light illumination of the objective human specific lighting devices. The proposed concept experimental model implemented using RGB LED lighting devices connected with IoT features open-source controller in the network along with networked video surveillance solution. The experiment results are verified with custom made automatic lighting control demon application integrated with OpenCV framework based computer vision methods to predict the human centric features and based on the estimated features the lighting illumination level and colors are controlled automatically. The experiment results received from the demon system are analyzed and used for the real-time development of a lighting system control strategy.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.1
• /
• pp.31-36
• /
• 2015

In this paper, an LED lighting system that is capable of automatic or maunal dimming control using a ultrasonic sensor and Bluetooth wireless communication technology is presented. The LED lighting system consists of a ultrasonic sensor, microcontroller unit, Bluetooth wireless communication, LED driver, and LED light source. By using the implemented LED lighting system sample, it is shown that the automatic and manual dimming control is realized. By using the ultrasonic sensor, the LED lighting is automatically brighter or dimmer depending on the distance between the sensor and an object. When using a smartphone that includes Bluetooth wireless communication function, one can not only manually control the brightness of the LED lighting from level 1 to 10, but also monitor the distance between the sensor and object on the smartphone.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.6
• /
• pp.70-76
• /
• 2016

Commercialization of surface lighting using Light Emitting Diodes (LED) has embraced the advance to Organic Light Emitting Diode (OLED) technology. This is necessary to achieve light-efficiency-improvement and longer component life. The range of application of LED lighting for both interior and outdoor lights has been gradually expanding. Automobiles and home appliances are now included. In the case of LED surface lighting in a domestic refrigerator, achieving high efficiency requires optimization of the number of LEDs in a pack. Optimization is also required in the design stage of development with regard to the conversion of the light source type from point light sources to the surface light type. This paper addresses these design problems. It presents a study of brightness variations for design solutions that differ from the existing technology in both the number of LED packages and use of Light Gathering Power (LGP) information. The intention is to facilitate production of high brightness LED surface lighting for domestic refrigerators.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.7B
• /
• pp.606-612
• /
• 2012

Visible light communications (VLC) uses modern solid-state LEDs to broadcast information. Emerging white-light LEDs allows the combination of lighting and optical wireless communication in one optical source. In this paper, a new LED lighting using one-chip-type white LED is proposed for efficient illumination and optical wireless communications. Performance analysis such as horizontal illuminance, 3-dB cut-off frequency, inter-symbol interference, signal-to-noise ratio and bit-error rate shows the effects of the shapes of LED lighting. Performance of the proposed LED lighting under the existence of obstacles is superior to that of the existing LED lighting in illumination and optical wireless communication.