• Journal of Adhesion and Interface
• /
• v.8 no.4
• /
• pp.1-7
• /
• 2007

Waterborne polyurethane (WPU) which is environment friendly has been rapidly used in coating and adhesive industries. However, the WPU is deficient in chemical resistance, thermal resistance, and mechanical property compared to solvent-based polyurethane. In this study, the WPU was synthesized from two types of polyester polyols, 4,4-dicyclohexylmethane diisocyanate ($H_{12}MDI$), dimethylolpropionic acid (DMPA), triethylamine (TEA) and ethylenediamine (EDA), organophilic nanoclay. The thermal stability, mechanical property of the WPU nanocomposite dispersion increased with increasing clay concentration. Especially, their peel strength showed their maximum value at 3 wt% of organophilic nanoclay contents.

• Journal of Adhesion and Interface
• /
• v.8 no.4
• /
• pp.23-31
• /
• 2007

An atmospheric plasma pre-treatment method was applied to EVA foam, Leather (Action), Rubber and Unwoven to improve its contact angle and adhesion using atmospheric plate type reactor. In order to investigate the optimum reaction condition of plasma treatment, type of reaction gas (nitrogen), rate of gas flow (30~100 mL/min), and reaction time (0~30 sec) were examined in a plate plasma reactor. The result of the surface modification with respect to the treatment procedure was characterized by using SEM. Due to a decrease of the contact angle of various materials, the greatest adhesion strength was achieved at optimum condition such as flow rate of 100 mL/min, reaction time of 10 second for an atmosphere nitrogen gas. Consequently, the atmospheric plasma treatment reduced the contact angle of the EVA foam, Leather (Action) and Rubber also resulted in the improvement of the adhesion.

• Elastomers and Composites
• /
• v.43 no.1
• /
• pp.1-7
• /
• 2008

Far-infrared vulcanization of ethylene-propylene-diene terpolymer(EPDM) compounds has been studied in comparison with hot air vulcanization. Vulcanization characteristics of EPDM compounds were measured by degree of curing and temperature of specimens in vulcanization process. As a result, degree of curing by far-infrared of EPDM compounds was shown to be higher value than that by hot air at the same vulcanization temperature. Especially, degree of curing by far-infrared on 3 mm thickness of EPDM compounds was increased by two times compared to that by hot air. While the increase of thermal conductivity of EPDM compounds highly improved degree of curing by far-infrared, that hardly improved degree of curing by hot air.

• Journal of Fashion Business
• /
• v.23 no.4
• /
• pp.127-139
• /
• 2019

Up-cycling has evolved from its original form of the simple recycling of waste, into an industry of its own that has been gaining momentum. In many developed industries, up-cycling is increasingly seen as an 'environmentally-friendly way of production and ethical way of consumption'. However, an examination of the designs of branded up-cycled products suggests that there is a need for product development fueled by further research on materials. The purpose of this study is to introduce various production methods that can overcome the shortcomings of using waste material and Korean motifs for use in product development, which ultimately contribute to enhancing the potential variety and character of up-cycled products. In order to do so, the up-cycling industry was examined to define key concepts, domestic and overseas markets were surveyed, and case analyses were conducted on domestic and foreign up-cycling brands. In addition, after tracking how leather is discarded and accumulated as waste and then collecting the discarded leather, the properties of the material were analyzed. A study of Korean motifs was followed by the concept summary, and upcycling design expressions that exemplify Korean images were identified. The following two novel methods were used to create six up-cycled bags using collected discarded leather. First, lucky bags and moon pots were selected from various Korean motifs in order to use motifs with identifiable features. Secondly, different variations of cutting and attachment methods were used, including iron mold production methods and presses.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.46-51
• /
• 2019

Intermittent CSR testing was used to investigate the degradation of a NBR O-ring, and also the prediction of its life-time. An intermittent CSR jig was designed taking into consideration the O-ring's environment under use. Degradation of O-rings by thermal aging was observed between $40^{\circ}C$ and $120^{\circ}C$. O-rings showed non-linear degradation behavior under $80^{\circ}C$. At 20% of failure condition, predicted life-times were 32.5 years by Arrhenius plot and 22.6 years by WLF plot.

• Composites Research
• /
• v.35 no.5
• /
• pp.309-316
• /
• 2022

The demand for cold-resistant cable material is increasing due to the rapid increase in the development of devices that operate in a low temperature environment. Cold tolerance of a thermoplastic polymer largely depends on the type and content of about 20 or more additives used to make the polymer. The phenomenon of polymer hardening at low temperature can be classified into hardening by simple temperature effect, embrittlement at the glass transition temperature, and hardening by crystallization of polymers that tend to crystallize. In this study, a thermoplastic polymer having a low glass transition temperature, a flame retardant, and an additive were mixed to evaluate the mechanical properties of a thermoplastic polymer composite material for electric wires. It has been confirmed that mechanical properties and processability are determined depending on the additives and compatibilizers added, and this study is considered to be useful as basic data for optimization to meet the performance requirements of wires developed for low-temperature use.

• Journal of Adhesion and Interface
• /
• v.13 no.3
• /
• pp.116-120
• /
• 2012

In this study, waterborne polyurethane was prepared from polyester polyol, $H_{12}MDI$, DMPA and sulfopropylated polypropyleneglycol-${\alpha}$,${\omega}$-diamine (SP). The $T_g$ of waterborne polyurethane was increased as the SP content increased, while it was decreased at the NCO/OH ratio of 1.8. Also the hydrolysis-resistance and tensile strength were increased as the SP content increased. The tensile strength decrement of WPU-SP was 2~5% with the exception of WPU-SP-1.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.1
• /
• pp.83-90
• /
• 2017

The polyurethane resin used for the garment skin leather surface coating was synthesized by varying the content of polyethylene glycol (PEG) in [NCO] / [OH] mole % ratio. The mechanical properties of the synthesized polyurethane resin were analyzed by SEM, FT-IR, UTM. As the [NCO] / [OH] mole % ratio of nonionic poly ethylene glycol (PEG) increased, there was no change in flexural resistance (dry, wet) and abrasion resistance and tensile strength measurement value were lowered. In contrast, the elongation property values were increased. The result of viscosity measurement showed that the viscosity became thinner with increasing [NCO] / [OH] mole % of PEG.

• Journal of Adhesion and Interface
• /
• v.17 no.4
• /
• pp.136-140
• /
• 2016

In this study, a series of dimer acid-based polyamides with different diamines were synthesized by condensation polymerization and the polyamides were characterized by Fourier transform infrared spectroscopy (FT-IR). Effects of diamine structures on mechanical and thermal properties of polyamides were investigated. The tensile strength and lap shear adhesion strength of aromatic-based polyamide (DAP) were higher than those of aliphatic-based polyamide (DAH). In DSC thermogram, DAP has a high $T_g$ and $T_m$ compared with DAH. DAP's and DAH's softening point were $112-115^{\circ}C$ and $98-121^{\circ}C$, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.1
• /
• pp.109-117
• /
• 2011

In this study, we experimented that how influence chain extension to waterborne urethane-epoxy hybrid resin for leather garment coatings. First of all, We had analyzed datas by FT-IR, SEM and machanical properties. By instruments analysis measurement we confirmed that synthesis of epoxy and hybrid resin. In this experiment we knew that polyurethane-epoxy hybrid resin have 5 grades of solvent resistance. Tensile strength measured in the polyurethane-epoxy resin(EDA 5.37g, 2.386 $kg_f/mm^2$) had the most strong strength.. Also polyurethane-epoxy hybrid resin had better result(EDA 5.37g. 37.4 mg. loss) than other hybrid resins. As hight proportion of EDA in hybid resin, we obtained low elongation and low flexibility. In this result, chain extension of waterborne polyurethane-epoxy hybrid resin showed that how effect in leather coating by ratio of EDA.