• 한국레이저가공학회지
• /
• 제3권3호
• /
• pp.13-19
• /
• 2000

The stencil is a thin stainless sheet in which a pattern is formed, which is placed on a surface of plate to reproduce the pattern of electric circuit. Conventionally the stencil has been produced by etching process. This process has many anti-environmental factors. In this study, Nd : YAG laser cutting process has been applied for stencil manufacturing. The study is focused on estimating kerf width of laser cut stencil by E.B.P.(Error Back-Propagation). This algorithm is good for estimating target value from input value. In this paper, target value was kerf width, and input values were frequency, pulse width, cutting speed and laser power. E.B.P. after teaming input and target could estimate kerf width from some variables precisely.

• 한국레이저가공학회지
• /
• 제4권3호
• /
• pp.30-39
• /
• 2001

This work was tamed out to apply a laser welding technique in joining between a Zn coated low carbon steel plate(SECC) and a free cutting carbon steel shaft(SUM24L) with or without W coating. Experiments were carried out and analysed by applying the FD(factorial design)method to obtain the optimum Laser welding condition. Optical microscopy, SEM, TEM and XRD analyses were performed in order to observe the microstructures in the fusion zone and the HAZ. Mechanical properties of the welded specimens were examined by microhardness test, tensile test and twist test. There was no flawed Zn in the fusion zone by EDS analysis. This means that during the welding process, Zn gas could be eliminated by appropriate shielding gas flow rate and butt welding gap. Ni coating itself did not influence on the tensile strength and hardness. However, twist bending strength and the weld depth of the Ni-coated free cutting carbon steel were lower as compared with those of the uncoated free cutting carbon steel. It was attributed to a lower absorbance of laser beam to the shin Ni surface. According to the results of the factorial design tests, the twist bending strength of welded specimens was primarily affected by pulse width, laser power, frequency and speed.

• 한국정밀공학회지
• /
• 제12권10호
• /
• pp.130-137
• /
• 1995

With the rapid growth of the die and mold, the new die making method has been developed. Especially, the laser is very useful, because it has a very fast cutting speed and is possible to manufacture complicated geometry. The quality of the laser cut is to be evaluated with respect to some characteristic quality parameters such as kerf width geometry, roughness and heat affected zone. This paper describes the laser cut characteristic(heat-affected zone) of the alloy tool steels(STD11) and the prediction of the kerf width genmetry by the FEM. On using the oxidation heat and laser beam, the prediction of kerf geometry is more accurate than that only by the laser beam. After laser cutting, the heat-affected zone is generated on the cutting cross section. The magnitude of hardness on the cutting cross section was similar to that of the heat treatment. It was possible to predict heat-affected zone by using the FEM program.

• 한국산학기술학회논문지
• /
• 제16권9호
• /
• pp.5748-5755
• /
• 2015

스크라이빙 공정은 LED 칩 생성을 위한 절단 공정으로 칩의 특성 및 생산량을 결정하는 중요한 공정이다. 기존의 기계적 방식 및 레이저 방식의 스크라이빙 공정은 칩의 열 변형 및 강도 저하, 절단 영역의 제한 등의 문제점이 있다. 이러한 문제를 해결하기 위해 웨이퍼 내부에 공극을 생성하여 자가 균열을 유도하는 내부 레이저 스크라이빙 공정이 연구되고 있으나 LED 칩 제작을 위한 사파이어 웨이퍼의 절단에 대한 연구는 미비한 실정이다. 본 논문은 LED 칩 제작에 사용되는 사파이어 웨이퍼의 내부 레이저 스크라이빙 공정을 적용하기 위해 주요 가공 변수를 정립하고 가공 실험을 통하여 절단 특성을 분석함으로써 내부 레이저 스크라이빙 시스템 구축을 위한 기초 가공 조건을 확립하였다.

• 반도체디스플레이기술학회지
• /
• 제18권4호
• /
• pp.62-68
• /
• 2019

The optoelectronic display units such as TFT-LCD or OLED require many thin optical plastic films and their mass manufacturing processes employ CO2 laser cutting of those thin films in a large quantity. However, laser film cutting could generate fume particles through melt shearing, vaporization, and chemical degradation and those particles could be of great concern for film surface contamination. In order to appreciate the fume particle dispersion behaviors in laser film cutting, this study relies on random particle simulations by probabilistic distributions of particle size, ejection velocity and angles coupled with Basset-Boussinesq-Oseen model of particle trajectory in low Reynolds number flows. Here, up to one million particles of random sampling have been tested to effectively show fume particles dispersed on the film surface. The computational results could show that particular range of fume particle size could easily disperse into the pixel region of processed optical films.

• 한국정밀공학회지
• /
• 제23권7호
• /
• pp.30-38
• /
• 2006

Laser cutting technology is one of flexible rapid manufacturing technologies with various advantageous including a high cutting speed, manufacturing of parts with a complex shape and others. The quality of the cut part and the optimum cutting conditions are highly dependent on the combination of the process parameters. The objective of this research works is to investigate the influence of process parameters, such as power of laser, cutting speed of laser and material thickness, on the surface roughness and the striation formation of the cut section for the case of cutting of CSP 1N sheet using high power Nd:YAG Laser with a continuous wave (CW). In order to find the relationship between process parameters and the surface roughness and the striation formation of the cut section, several experiments are carried out. Through the investigation of the empirical results, it has been shown that the surface roughness is highly related to the striation formation, including the frequency and angle of the striation, of the cut section. From the results of experiments, an optimum cutting speed for each cutting condition has been obtained to improve both the quality of the cut surface and the cutting efficiency.

• Journal of Electrical Engineering and Technology
• /
• 제7권4호
• /
• pp.576-581
• /
• 2012

A 23 W continuous wavelength $CO_2$ laser system exited by a high-frequency LCC resonant converter is adapted to cut a biodegradable rope fabricated with polybutylene succinate. As the biodegradable rope consists of three twisted strands, the thickness changes relative to the position of the laser beam and we thus propose a method to determine exact cutting depth. In order to obtain the parameters related to the rope cutting, the experimental and theoretical cutting depths are compared and analyzed for a range of laser heat sources. The melted thickness and groove width of the cut biodegradable rope are also examined. The proposed theoretical cutting depth depends on the incident power and target velocity ratio. From these experimental results, the biodegradable rope with a diameter of 22 mm can be cut with a heat source of 50 J/cm resulting in a melted thickness of 1.96 mm and a groove width of 0.65 mm. The laser system is shown to be perfect tool for the processing of biodegradable rope without the occurrence of raveling.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 추계학술대회 논문집
• /
• pp.81-85
• /
• 1992

Quality of cut is strongly dependent on the cutting pressure, so this relationship can be identified by pressure measuring system. In this paper, the experiments presented were performed with the devised pressure measuring system and the laser cutting of STS 304. Convergent type and convergent-divergent type nozzle were used for pressure variation of the distance between nozzle and workpiece. In laser cutting of STS 304, 1.0 kW CO $\_$2/ laser used. The convergent type nozzle(1.0 mm diameter) pressured above 3 kgf/cm $\^$2/, the MSD(Mach Shock Disk) created, which caused the the pressure variations of the distance between nozzle and workpiece. The maximum cutting pressure exists in accordance with the variation of distance. In spite of far distance the maximum cutting pressure is achieved by using the pressure measuring system. The higher cutting pressure beneath the workpiece the less quantity of dross and the kerf width. Since the higher cutting pressure helps to remove the quantity of dross and to stop the exothermic energy into the material. The optimum laser cutting parameter of STS 304(2.0 mm thickness) with the convergent type nozzle(1.0 mm diameter)is 0.75 mm and 2.5 mm distance between nozzle and workpiece, 4 kgf/cm $\^$2/ cutting pressure. In 3.0 mm thickness case, 1.5 mm and 2.25 mm distance is achieved for good quality.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.33-38
• /
• 2012

An experimental study was carried out to observe the characteristics of impingement of assist gas from a rectangular supersonic nozzle on kerf surface in laser machining. A micro-scale supersonic (Mach number 2.0) rectangular nozzle system was designed and fabricated for the purposes, and hot tests of the performance of the nozzle system was proceeded in the ITI corporation laboratory. For various related parameters such as laser powers, nozzle pressures and cutting speeds, the quality of the frontal view of cut edge surfaces was observed by a microscope. In the study, it was shown that the application of the present micro-rectangular supersonic nozzle in an off-axis configuration made it possible to cut a mild steel, by combinations of relatively low laser - powers, large standoff distances, and assist gas with no oxygen, which was not achieved by conventional laser cutting processes.

• 한국정밀공학회지
• /
• 제26권9호
• /
• pp.127-134
• /
• 2009

Laser-assisted machining uses primarily laser power to heat the local area before the material is removed. It not only efficiently reduces the cutting force during the manufacturing process but also improves the machining characteristics and accuracy with regard to difficult-to-machine materials. The prediction of relative deformations between the cutting tool and workpiece is important to improve the accuracy of machined components. This paper presents the deformation errors caused for a cylindrical workpiece by thermal effects in the laser-assisted machine tool using finite element method. The results can be used to increase the cutting accuracy by compensating thermal distortion prior to laser-assisted machining.