• Corrosion Science and Technology
• /
• 제3권4호
• /
• pp.172-177
• /
• 2004

Biaxially oriented polyethylene terephthalate copolymer(BO - PET)film laminated aluminiums have been applied for chip condenser case. The BO PET film is characterized by high molecular which gives high corrosion resistance, good adhesion and high heat resistance. The higher orientation lowers formability of the film. So, optimum orientation has to be controlled during the laminating process. And to confirm the adhesion between BO PET and aluminium and to guarantee the formability of PET laminated aluminums, we have controlled the chromium oxides weight on the aluminium and laminating condition ( laminating temperature, soaking temperature and lag time after nip roll and quenching conditions) This paper discusses the effect of the laminating conditions on the formability of laminated aluminums. As results, it is clear that the orientation of the BO PET film decreased with an increase in the strip temperature. When the film temperature is over the melting point of the film, its orientation drastically decreased.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.169-173
• /
• 2003

We demonstrated the applicability of dry film photoresist (DFR) in photolithography process for fine pitch solder bumping on the polytetrafluoroethylene (PTFE/Teflon) printed circuit board (PCB). The copper lines were formed with $100\;{\mu}m$ width and $18\;{\mu}m$ thickness on the PTFE test board, and varying the gaps between two copper lines in a range of $100-200\;{\mu}m$. The DFRs of $15\;{\mu}m$ thickness were laminated by hot roll laminator, by varying laminating temperature from $100^{\circ}C\;to\;150^{\circ}C$ and laminating speed. We found the optimum process of DFR lamination on PTFE PCB and accomplished the formation of indium solder bumps. The optimum lamination condition was temperature of $150^{\circ}C$ and speed of about 0.63 cm/s. And the smallest size of indium solder bump was diameter of $50\;{\mu}m$ with pitch of $100\;{\mu}m$.

• Transactions on Electrical and Electronic Materials
• /
• 제9권1호
• /
• pp.33-37
• /
• 2008

This paper describes the development of a new $5.0{\times}3.2mm$ SAW filter bank which is consist of 12 L, C matching components and 4 SAW bare chips on PCB substrate with CSP technology. We improved the manufacturing cost by removing the ceramic package through direct flip bonding of $LiTaO_3$ SAW bare chip on PCB board after mounting L, C passive element on PCB board. After that we realized the hermitic sealing by laminating the epoxy film. To confirm the confidentiality and durability of the above method, we have obtained the optimum flip bonding & film laminating condition, and figured out material property and structure to secure the durability & moisture proof of PCB board. The newly developed super mini $5.0{\times}3.2mm$ filter bank shows the superior features than those of existing products in confidence, electrical, mechanical characters.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.597-598
• /
• 2006

This paper describes a development of a new $1.4{\times}1.1$ and $2.0{\times}1.4mm$ RF SAW filters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• Journal of Astronomy and Space Sciences
• /
• 제2권2호
• /
• pp.153-174
• /
• 1985

The one of critical factor in gas turbine engine performance is high turbine inlet gas temperature. Therefore, the turbine rotor has so many problems which must be considered such as the turbine blade cooling, thermal stress of turbine disk due to severe temperature gradient, turbine rotor tip clearance, under the high operating temperature. The purpose of this study is to provider the temperature distribution and heat flux in turbine disk which is required to considered premensioned problem by the Finite Difference Method and the Finite Element Methods on the steady state condition. In this study, the optimum aspect ratio of turbine disk was analysed for various heat conductivity of turbine disk material by Finite Difference Method, and the effect of laminating method with high conductivity materials to disk thickness direction by Finite Element Methods in order to cool the disk. The laminating method with high conductivity material on the side of the disk is effective.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1253-1259
• /
• 1996

In the fabrication of alumina-based multilayer ceramics sintering shrinkages with lamination conditions such as lamination pressure temperature and laminating with and without press die were compared. The sintering shrinkage was affected substantially by lamination pressure and temperature and in the case of laminatino without press die the lower laminated density and a large difference in shrinkage with direction were observed. These results can be explained by introducing a new factor which is the ratio of the changes of areas before and after lamination.

• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.21-28
• /
• 2004

Polytetrafluoroethylene (PTFE/Teflon ) 인쇄회로기판용 미세 피치 솔더 범프 형성을 위해 dry film photoresist (DFR)를 photolithography 공정에 적용하였다. DFR lamination을 위한 test board는 폭 100$\mu\textrm{m}$와 두께 18$\mu\textrm{m}$의 copper line들이 100-200$\mu\textrm{m}$의 간격으로 배열된 형태로 디자인하였다. 15$\mu\textrm{m}$의 두께를 갖는 DFR을 hot roll laminator를 사용하여 lamination 온도와 속도를 변화시켜가면서 lamination 공정 실험을 수행하였다. 실험 결과, PTFE 인쇄회로기판에 DFR을 lamination하는 공정의 최적 조건은 lamination 온도 $150^{\circ}C$, 속도 약 0.63cm/s였다. UV exposure 및 development 공정을 거쳐 저융점 솔더 재료인 인듐을 증착하였다. DFR 박리 순서에 따른 두 가지 다른 reflow 공정을 통해 최소 지름 50$\mu\textrm{m}$, 최소 피치 100$\mu\textrm{m}$를 갖는 인듐 솔더 범프를 형성하였다.

• 대한전자공학회논문지SD
• /
• 제43권11호
• /
• pp.8-13
• /
• 2006

최근 RF용 탄성표면파 필터는 HTCC 패키지를 이용한 칩스케일 패키지 공법으로 제작되고 있다. 본 연구에서는 HTCC 패키지를 이용하는 대신에 BT 레진 계열의 PCB 기판을 이용하여 $1.4{\times}1.1$과 $2.0{\times}1.4mm$ 규격을 가지는 새로운 SAW RF 필터를 개발하였다. 본 기술을 적용하여 기존대비 약 40% 이상의 재료비 절감효과를 얻을 수 있다. 다층 PCB 기판과 $LiTaO_3$ 탄성표면파 기간간의 플립 본딩 조건을 최적화하였고, 적절한 PCB 재료선정을 통하여 PCB 기판 및 에폭시 라미네이팅 필름간의 열팽창계수 차이로 인해 발생하는 응력을 최소화시켰다. 이렇게 개발된 탄성표면파 필터는 기존의 제품에 비해 신뢰성 및 전기적 특성면에서 향상된 특성을 보였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.67-70
• /
• 2007

LTCC (Low Temperature Co-fired Ceramic) has been emerged as a promising technology in packaging industry. In this technology the lamination and the sintering process are very important because they change the permittivity of ceramics and the dimension of metal pattern which have influences on electric property. In this paper we studied on influence of the permittivity and the dimension change by lamination pressure and sintering temperature of LTCC process. As a results, permittivity increase along with increasing of lamination pressure and sintering temperature.

• 소성∙가공
• /
• 제16권5호통권95호
• /
• pp.396-400
• /
• 2007

LTCC(Low Temperature Co-fired Ceramic) which offers a good performance to produce multilayer structures with electronic circuits and components has emerged as an attractive technology in the electronic packaging industry. In LTCC module fabrication process, the lamination and the sintering are very important processes and affect the electrical characteristics of the final products because the processes change the permittivity of ceramics and the dimension of the circuit patterns which have influences on electronic properties. This paper discusses the influence of lamination pressure and sintering temperature on the permittivity and the dimensional change of LTCC products. In the present investigation, it is shown that the permittivity increases along with increasing of the lamination pressure and the sintering temperature.