• Tribology and Lubricants
• /
• v.30 no.1
• /
• pp.9-14
• /
• 2014

In this Part II study, rotordynamic stability analyses were carried out to confirm improvements to the stability of a process high-speed lightweight centrifugal compressor, depending on the effects of tilting pad journal bearing designs. The bearing design variables considered were the clearances, LBPs, LOPs, and preloads. The results showed that the rotordynamic stability of the subject compressor rotor-bearing system improves exactly in accordance with the effects of the bearing design variables, which were determined in the preceding Part I study, owing to reduced bearing stiffnesses. Specifically, it was confirmed that the stability of the rotor system can be greatly improved by increasing both the machined and assembled bearing clearances, but there were no stability improvements by simply changing from an LBP to an LOP design. In addition, it was confirmed that for given fixed machined bearing clearances, the stability can be additionally improved by decreasing the preloads, i.e., by increasing the assembled clearances. In conclusion, it may be necessary to improve the designs of the original tilting pad bearings to obtain a sufficient margin of rotordynamic stability against a possible aerodynamic cross-coupled stiffness in a process high-speed centrifugal compressor. Thus, increasing the machined and assembled bearing clearances and decreasing the preload could be effective solutions.

• Journal of the Korea Concrete Institute
• /
• v.24 no.2
• /
• pp.129-136
• /
• 2012

Compression splices are required for all compression members in almost all of the floors in high-rise buildings. Therefore, a clear understanding of the behavior of compression splices can provide a rational design of compression splices. Tests of compression splices with bearing only and bond only cases were conducted to investigate the component resistance characteristics of compression splices. Test results showed that the circumferential tensile stresses induced by bearing and bond overlapped at the end of the splice length deterred bond and bearing splices from developing target splicing strength when both normal bond and bearing splices were used. In particular, the bearing strength was more significantly reduced than the bond strength since the bearing relied on the limited area near the end of the splice length. However, the strength of the normal splice was always higher than the strength of the bond only or the bearing only case. Consequently, the study results showed that splice strength in compression cannot be improved by means of removing bond or bearing. In addition, the bond strength in bond only splices was nearly same as the bond strength in tension splices and the strength increase of compression splice is attributed to end bearing only characteristic.

• The Journal of Korean Physical Therapy
• /
• v.28 no.6
• /
• pp.381-384
• /
• 2016

Purpose: Previous studies reported changes in the first metatarsophalangeal (MTP) joint angle in relation with and without weight bearing, but it is unclear whether sesamoid bone of the great toe changes in weight bearing conditions particularly in subjects with hallux valgus (HV). To investigate how weight bearing conditions can affect the position of the medial sesamoid bone (MSB), first MTP joint angle, and second intermetatarsal angle (IMA) in the recruited subjects. Methods: Subjects were recruited 24 with HV and 21 without HV in study. X-rays were taken in the weight bearing and non-weight bearing conditions. The distance of the MSB, first MTP joint angle, and second IMA were measured from the radiographs. Data were analyzed by paired and Independent t-test. The statistical significance level was p<0.05. Results: In both groups, the first MTP joint angles and the distance of the MSB were significantly smaller, while the second IMA was significantly greater in the weight bearing condition. The difference in the distance of the MSB between the two postures was significantly greater in the group with HV. Conclusion: Weight bearing can affect the first MTP joint angle, second IMA, and position of the MSB; the change in the position of the MSB in weight bearing was greater in the group with hallux valgus. The difference in these variables between weight bearing and non-weight bearing conditions may be considered when measuring HV.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.6
• /
• pp.412-421
• /
• 2018

The Line array sonar consisting of several hydrophones increases array gain and improves the performance for detecting the direction of the target compared to single hydrophone. However, line array sonar produces the bearing error that makes it difficult to determine the bearing of incoming source signal due to the relation between bearing angle of target and vertical angle of multipath signals. Vertical angles of multipath are varied with the geometry of receiver and target and various underwater environments, therefore it is necessary to consider the bearing error to estimate accurately the bearing of the target. In this study, acoustic modelling was performed to understand the effect of multipath signals on the target signal. The errors of bearing angle estimated from the bottom bounced signals are calculated with several environment. In addition, the expected bearing line, as a function of source-receiver range, compensated for the bearing error is predicted from the estimated bearing angle.

• KSTLE International Journal
• /
• v.7 no.2
• /
• pp.35-44
• /
• 2006

Turbocharger bearings are under the circumstance of high temperature, moreover rotated at high speed. It is necessary to be designed overcoming the high temperature. So the type of oil inlet port, the inlet oil temperature and the sort of engine oil should be designed, controlled and selected carefully in order to reduce the bearing inside temperature. In this study, the influence of aerated oil on a high-speed journal bearing is also examined by using the classical thermohydrodynamic lubrication theory coupled with analytical models for viscosity and density of air-oil mixture in fluid-film bearing. Convection to the walls and mixing with supply oil and re-circulating oil are considered. The considered parameters for the study of bubbly lubrication are oil inlet port's type, oil aeration level and shaft speed. It is found that the type of oil inlet ports and shaft speed play important roles in determining the temperature and pressure, then the friction and load of journal bearing at high speed operation. Also, the results show that, under extremely high shaft speed, the high shear effects on aerated oil and the high temperature effects are canceled out each other. So, the bearing load and friction show almost no difference between the aerated oil and pure oil.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.203-210
• /
• 2006

Two kinds of crankshaft oil supply system which were called continuous and discontinuous oil sup-ply system have recently been adopted in engine developing process. In order to clarify the lubrication characteristics for theses systems, in this paper, the comparison studies on supplied oil temperature, pressure, aspect ratio of bearings, and radial clearance were carried out for the main and the connecting rod bearing using computational fluid dynamic analysis.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.274-281
• /
• 2000

In this paper, linearized dynamic characteristics of parallel line pivoted pad thrust bearing (here-inafter refer to PLP thrust bearing) was analyzed by perturbation method with inlet pressure. Inlet pressure and excitation frequency influence dynamic characteristics of PLP thrust bearing at all operating conditions, such as angular pivot position, mass of pad. Therefore, the characteristics have to be analyzed with inlet pressure, excitation frequency, mass of pad and thickness of pad. Otherwise, the analysis may be over or under estimate.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.24-28
• /
• 1999

This paper describes a new pivoting technique to improve bearing performance in pivoted pad thrust bearings. This new technique adjusts the pivot line in a line pivoted pad thrust bearing to be parallel to the trailing edge of a sector shaped pad. Bearing performance factors such as load carrying capacity, frictional torque and flow rate are numerically investigated for conventional point-pivoted and line-pivoted pads and for the new parallel-line pivoting technique. It is shown that the load carving capacity can be maximized with the new technique.

• Tribology and Lubricants
• /
• v.27 no.5
• /
• pp.256-263
• /
• 2011

Bearings of marine engines are operated under severe conditions because of dynamic load and low sliding speed. This paper deals with lubrication analysis of a crank pin bearing for a marine diesel engine. Journal center locus and oil film thickness are compared of crank pin bearing. In the past researches, journal bearings have been studied only about the surface of bearing. In addition to this conventional research, this paper analyzes the effect of roundness error of a journal and a bearing on the minimum film thickness. Numerical analysis has been studied by using Reynolds equation and also Half-Sommerfeld condition is applied as boundary condition. Futhermore, this study investigates the effect of roundness error change on the minimum film thickness. The results demonstrate that the bigger amplitude of roundness error yields, the lower minimum oil film thickness is. In comparison to previous research considered a journal and a bearing individually, the results considering a journal and a bearing together show that amplitude of roundness error of journal has very little effect on the minimum oil film thickness.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.189-193
• /
• 2008

Performance of refrigerant oil at the thrust-bearing and at the journal-bearing of a scroll compressor is a significant factor. This paper presents the friction and anti-wear characteristics of nano oil with a mixture of a refrigerant oil and carbon nano particles in the journal bearing of scroll compressors. The characteristics of friction and anti-wear using nano-oil is evaluated using the disk on disk tester and the journal bearing tester for measuring friction surface temperature and the coefficient of friction at the journal bearing tester. In journal bearing test, the average friction coefficient of high concentration nano-oil was decreased down to 18% compared to raw oil under 4,500 N and 3,600 rpm. It is believed that nano particles can be coated on the wear surfaces and the interaction of nano particles between surfaces can be improved the lubrication in the friction surfaces. Worn surfaces of frictional specimen were measured with straightness. carbon nano oil enhances the characteristics of the anti-wear and friction at the joural bearing of scroll compressors.