• Composites Research
• /
• 제28권6호
• /
• pp.348-355
• /
• 2015

접착 조인트는 환경조건 및 작업자의 숙련도에 따라 접착강도가 크게 변화될 수 있으므로 이에 대한 비파괴 검사법은 매우 중요하다. 최근 접착제에 1-2 wt%의 CNT를 첨가하고 저항변화를 측정하여 접착 체결부의 내부 결함을 검출하는 전기저항법이 제시되었다. 전기저항법에서는 동일조건에서 접착조인트의 저항값이 일정하도록 하기 위하여 CNT의 균일한 분산이 매우 중요하며 이에 따라 결함 검출의 정확도가 좌우된다. 본 연구에서는 4가지 분산 방법으로 CNT를 접착제에 분산시켜 접착조인트을 제작하고 전기적 물리량을 측정하였다. 초음파를 이용한 CNT의 전처리 및 기화과정, 물리적 교반 방법등을 선정하여 효율적인 분산방법을 정립하고 분산성을 평가할 수 있는 척도를 제시하였으며 일반적인 분산 방법 대비 선정된 분산 방법을 적용했을 때 전기저항법의 결함검출능을 비교하였다.

• Nuclear Engineering and Technology
• /
• 제55권11호
• /
• pp.4066-4076
• /
• 2023

Pressure resistance welding is usually used to seal the connection between the cladding tube and the end plug made of zirconium alloy. The seal welded joint has a direct effect on the service performance of the fuel rod cladding structure. In this paper, the pressure resistance welded joints of zirconium alloy tube-plug structure were obtained by thermal-mechanical simulation experiments. The microstructure and microhardness of the joints were both analyzed. The effect of processing parameters on the microstructure was studied in detail. The results showed that there was no β-Zr phase observed in the joint, and no obvious element segregation. There were different types of Widmanstätten structure in the thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ) of the cladding tube and the end plug joint because of the low cooling rate. Some part of the grains in the joint grew up due to overheating. Its size was about 2.8 times that of the base metal grains. Due to the high dislocation density and texture evolution, the microhardnesses of TMAZ and HAZ were both significantly higher than that of the base metal, and the microhardness of the TMAZ was the highest. With the increasing of welding temperature, the proportion of recrystallization in TMAZ decreased, which was caused by the increasing of strain rate and dislocation annihilation.

• Structural Engineering and Mechanics
• /
• 제67권1호
• /
• pp.1-8
• /
• 2018

Shake table tests performed on five 1:3 reduced scale two story RC moment resisting frames having construction defects, have shown severe joint damageability in deficient RC frames, resulting in joint panels' cover spalling and core concrete crushing. Haunch retrofitting technique was adopted herein to upgrade the seismic resistance of the deficient RC frames. Additional four deficient RC frames were built and retrofitted with steel haunch; both axially stiffer and deformable with energy dissipation, fixed to the beam-column connections to reduce shear demand on joint panels. The as-built and retrofitted frames' seismic response parameters are calculated and compared to evaluate the viability of haunch retrofitting technique. The haunch retrofitting technique increased the lateral stiffness and strength of the structure, resulting in the increase of structure's overstrength. The retrofitting increased response modification factor R by 60% to 100%. Further, the input excitation PGA was correlated with the lateral roof displacement to derive structure response curve that have shown significant resistance of retrofitted models against input excitations. The technique can significantly enhance the seismic performance of deficient RC frames, particularly against the frequent and rare earthquake events, hence, promising for seismic risk mitigation.

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권4호
• /
• pp.16-24
• /
• 2022

Applications of REBa₂Cu₃O_7-δ tapes require joints with a simple manufacturing process, low resistance and good mechanical properties. In the present study, we successfully developed a copper diffusion joint between Cu-stabilized REBa₂Cu₃O_7-δ tapes that meets the above requirements without solder simply by applying flux, heat and pressurization. After a 3 min thermocompression process at approximately 150 δ and 336 MPa in air, two tapes were directly connected between Cu stabilizers by copper diffusion, which was proven by microstructure analysis. The specific resistivity of the copper diffusion joint reached 5.8 nΩ·cm² (resistance of 0.4 nΩ for a 306 mm splicing length) at 77 K in the self-field. The axial tensile stress reached 200 N without critical current degradation. The results show promise for the preparation of copper diffusion joints to be used in coils, attached tapes, and wire/cable terminals.

• 대한기계학회논문집A
• /
• 제35권7호
• /
• pp.799-804
• /
• 2011

본 논문에서는 칩저항을 실장하는 솔더에 대한 온도사이클 시험을 수행하고, 그 결과로부터 고장 예지 실현을 위한 열하중에서의 솔더실장의 고장메커니즘을 연구하였다. 시험 중 솔더의 고장을 모니터링하기 위하여 실장된 칩저항 양단간의 저항 변화를 데이터 측정기로 실시간 관찰하였다. 관찰 데이터로부터 솔더의 크랙 진전 중과 크랙 진전 완료 시점의 고장 메커니즘을 제시하였다. 제시된 고장 메커니즘을 유한요소법으로 검증하여 솔더의 크랙이 진전 중에는 저온조건에서 크랙이 열리고 저항이 증가하며, 크랙의 진전이 완료된 후에는 고온조건에서 크랙이 열리고 저항이 증가하는 조건으로 바뀜을 보였다. 이런 결과에 기반하여 온도 사이클에서 저항측정을 통해 칩저항 실장 솔더의 고장예지가 가능함을 제시하였다.

• International Journal of Internet, Broadcasting and Communication
• /
• 제12권1호
• /
• pp.81-89
• /
• 2020

The purpose of this study is to investigation the effects of functional compression clothing on muscle function by comparing the iEMG response of muscle during exercise according to the wearing of taping applied functional clothing. Six men in their twenties in Chungcheongnam-do were selected for the study. Resistance exercise was performed by cross-distributing the conditions of wearing and not wearing functional clothing. Resistance exercises for iEMG measurements are biceps curl, wrist curl, reverse wrist curl, kickback and push-up. iEMG measurement muscles were the biceps brachii, triceps brachii, extensor carpi ulnaris, flexor carpi radialis. During biceps curl exercise, the iEMG of triceps brachii, biceps brachii wearing condition was lower than the non-wearing condition. During kickback exercise, the iEMG of triceps brachii, extensor carpi ulnaris wearing condition was lower than the non-wearing condition. During reverse wrist curl exercise, the iEMG of extensor carpi ulnaris wearing condition was lower than the non-wearing condition. During wrist curl exercise, the iEMG of flexsor biceps brachii, carpi radialis wearing condition was lower than the non-wearing condition. During push-up exercise, the iEMG of triceps flexsor biceps brachii, carpi radialis, brachii, biceps brachii non-wearing condition was lower than the wearing condition.

• 한국응용곤충학회지
• /
• 제31권3호
• /
• pp.314-327
• /
• 1992

Insecticide resistance is a serious is a serious threat to IPM, resulting in various adverse effects not to mention the loss of yield in agriculture. One approach to counter the problem is the disruption of resistance mechanisms. This can be achieved by (1) compounds which show a negative correlation with resistance at the site of action, (2) specific metabolic inhibitors which serve as synergists, or (3) a certain combination of two insecticides producing a joint action. This approach, however, requires certain precautions for the side effects may cause an increase in toxicity to mammals. Owing to the recent advances in theoretical studies on resistance management employing computer simulation and mathematical models, a few principles to reduce the risk of development of resistance have been clarified. They are helpful in designing operational strategies with regard to, for instance, insecticide doses to be applied, mode of application, and choice and nature of the insecticide(s) to be used. For restoration of insecticide susceptibility of a resistant population, reintroduction of susceptible individuals to the resistant population is feasible when certain conditions are met. Natural enemies which developed resistance to insecticides can be an important component of IPM as has been shown in the pest management in apple orchards. After all, the implementation of a successful resistance management program depends upon cooperation between different sigments of the agricutural community. Although resistance is a preadaptive phenomenon, in some cases spontaneous loss of resistance does occur without contamination by susceptible individuals. The instability of resistance in these insects implies the possible existence of a switch machanism controlling the expression of resistance gene(s). Elucidation of such a mechanism may eventually provide us with a new technical approach with which we can combat the problem of insecticide resistance.

• 한국전기전자재료학회논문지
• /
• 제13권3호
• /
• pp.247-253
• /
• 2000

We evaluated the electric properties of Bi-2223 jointed tapes processed by both resistive-and superconducting-joint methods. For resistive-joint. filler materials of wood metal Pb/Sn. In and silver paste were used whereas for superconductive-joint lap joint method was used. In the resistive joint tape. critical transport property(CCR) n-value and contact resistance were observed to be in the range of 10-85% 1-8,9. and 0.71x10$\^$-6/-0.13x10$\^$-6/Ω, respectively. depending on their filler materials. Specifically it is believed that the electrical properties of resistive joint tape are significantly related to the resistivity of filler materials. On the other hand the CCR of superconductin joint type was varied 55 to 85% with uniaxial pressure probably due to the irregular microstructure in the transition region.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1373-1383
• /
• 2018

Experimental study was conducted to investigate the seismic behavior of roof joint. Eight full-scale specimens were tested considering the effects of axial force, joint height, hole shape of base plate and edge distance of concrete on the failure mode and resistance capacity of roof joint. With the increase of axial force, the hysteretic curves were fuller. The mechanical model of roof joint change from bending to shear. With the increase of joint height, the ultimate strength of roof joint decreased. If the hole shape of base plate changed from circle to loose, the slip behavior of roof joint appeared and the ultimate strength of roof joint decreased. The damage of edge concrete may occur if the edge distance of concrete was not big enough.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.217-217
• /
• 2009

In this study, the effect of bending strain on the transport property and critical current of lap and butt-jointed BSCCO tapes have been investigated. The samples were joined using a mechanically controlled jointing procedure. In order to ensure a uniform pressure application at the joint part, a single point contact has been devised and also to achieve a uniform thickness at the joint interface.