• Journal of Korea Foundry Society
• /
• v.21 no.5
• /
• pp.272-279
• /
• 2001

• Journal of Korea Foundry Society
• /
• v.21 no.5
• /
• pp.265-271
• /
• 2001

• Journal of Korea Foundry Society
• /
• v.21 no.2
• /
• pp.85-92
• /
• 2001

• KCID journal
• /
• v.6 no.2
• /
• pp.70-82
• /
• 1999

• KCID journal
• /
• v.8 no.2
• /
• pp.9-15
• /
• 2001

• Journal of the Korean Institute of Educational Facilities
• /
• v.7 no.4
• /
• pp.72-79
• /
• 2000

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.08a
• /
• pp.270-270
• /
• 2008

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.69-74
• /
• 2019

The influence of measuring fixtures on the measurement of dielectric and piezoelectric properties of PMN-PT single crystal specimens was investigated. As the pressure of the jig pin which applied the AC electrical signal to the sample decreased, the lower resonance resistance was measured and the higher mechanical quality factor was calculated. The mechanical quality factor was 418 when the spring tension of the jig pin was 20grf, and the value of the quality factor was reduced by half when the spring tension was 200grf. The 4-probe fixture method is unsuitable for measuring piezoelectric properties, but it was suitable for the measurement of dielectric loss. In order to accurately evaluate the piezoelectric properties of PMN-PT, it is necessary to lower the spring tension of the jig pin as much as possible.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.3
• /
• pp.301-306
• /
• 2009

In this study a 3-component rotating balance, which is designed to measure the thrust (Fz) and two moment components (Mx, My) simultaneously for a rotor test jig, is designed and its performance is validated experimentally. The low voltage signal from the strain gages mounted on the balance is amplified with a rotating amplifier, which is then fed through a slip-ring unit into the data acquisition system. In order to validate the accuracy of the calibration matrix obtained from a static calibration test, an additional reaction type balance is used to measure the thrust from a model rotor simultaneously, and shows very good result. Finally, the expanded uncertainty value, which is obtained from ISO method is estimated to be $2.82\times10^{-1}$, and the balance turns out to be reliable.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.252-261
• /
• 2014

Marine casualties originated from fishing vessel occupied about 70% of the whole marine casualties in Korea from 2001 to 2010, this ratio was not much changed as it was before. Therefore a pragmatic counterplan to decrease of casualties in fishing vessel is indispensable for reduction of the nationwide marine casualties. But since the casualties occurred by fishing vessel may have a different causes and counterplan according to the operating type of it, in this paper, fishing vessels classified into 12 types by operating method and inspected the causes and counterplan for that. The operating type of fishing vessel occurred the specific casualties more were jig boat in collisions and fire explosion, trap fishing boat, mixed fishing boats and inshore gill netter in collisions, stow netter in machinery damages and capsizing, offshore gill netter in machinery damages, fish carrier in collisions. It must be emphasized that the higher ranked types of vessels, especially jig boat have to take special care to the approaching vessels under way, trap fishing boat to rear look out and mixed fishing boat must keep on safety speed and be taken an education for advance the skill of operating radar as well. For all 12 types of fishing vessel, it is necessary for an operator to make strict precaution on the other vessel under way systematically and keep the regulation for preventing collisions, and for an engineer on watch to make a check the electricity and the engines periodically for reduction the fire explosion and machinery damages.