• Ocean Systems Engineering
• /
• v.2 no.1
• /
• pp.17-31
• /
• 2012

This study investigated the behavior of a non-isothermal $CO_2$ bubble formed through a leak process from a high-pressure source in a deep sea. Isenthalpic interpretation was employed to predict the state of the bubble just after the leak. Three modes of mass loss from the rising bubble were demonstrated: dissolution induced by mass transfer, condensation by heat transfer and phase separation by pressure decrease. A graphical interpretation of the last mode was provided in the pressure-enthalpy diagram. A threshold pressure (17.12 bar) was identified below which the last mode was no longer present. The second mode was as effective as the first for a bubble formed in deep water, leading to faster mass loss. To the contrary, only the first mode was active for a bubble formed in a shallow region. The third mode was insignificant for all cases.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.770-775
• /
• 2015

Adsorption of Congo Red (CR) from dye-containing effluents using modified bentonite (MB) has been investigated here. Isothermal studies were conducted to ascertain maximum adsorption capacity of the adsorbent. MB exhibited superior adsorption capacity compared to other low-cost adsorbents. Experimental data fitted the Langmuir isotherm better, indicating monolayer coverage of CR on MB. The feasibility of the process was measured in terms of separation factor $R_L$. The values of Gibbs free energy, entropy and enthalpy were calculated from the thermodynamics of the process. Adsorption was feasible and spontaneous, being endothermic. Analytical techniques including SEM, EDS, FTIR and XRD were applied to characterize MB and also to provide conclusive proof of the accumulation of CR on to MB.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.7
• /
• pp.91-100
• /
• 1999

This paper investigates ventilation characteristics of an environmental chamber simulating an under-floor air conditioning system for isothermal and cooling supply air conditions. The tracer gas sulfur-hexafluoride (SF$F_6$) was injected into a supply duct using step-up and step-down methods. Local mean and room mean ages were calculated from the concentrations measured at internal points and at the exhaust duct. The air change efficiency of the chamber has been found to be greater in cooling conditions than in isothermal conditions. Also the room air change efficiency is not significantly affected but slightly improved by the presence of a supply diffuser.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.3 no.5
• /
• pp.365-375
• /
• 1991

Confined natural convection due to lateral temperature difference in rectangular enclosures was studied numerically and experimentally for the insulated and the constant temperature enclosures. In the case of insulated enclosure, the flow pattern and heat transfer modes are rather simple depending mainly upon Rayleigh number. In the case of isothermal enclosure, however, the phenomena of flow and heat transfer are somewhat complex and interesting due to the stable thermal gradients and various circumstances resulted from four wall temperature conditions. As a dimensionless variable, to describe properly the flow and heat transfer phenomena in the isothermal enclosure, temperature difference ratio ${\Delta}T_v/{\Delta}T_H$ is newly introduced and this parameter seems to be appropriate in the analysis of results on the effect of stabilizing thermal gradient.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.380-380
• /
• 2006

Styrene-Butadiene diblock or styrene-butadiene-styrene triblock copolymers are industrially important materials for asphalt modification and adhesives. A kinetic modeling study on non-isothermal anionic styrene-butadiene diblock copolymerization system is presented. The model deals with the association/dissociation reaction of initiator and propagating ion pairs in its kinetic scheme. By comparing model calculation results with real plant data, it is possible to obtain useful ideas for more efficient plant operation. For example, the model clearly provides important relation between the reaction temperature profile and the conversion of monomers.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.167-172
• /
• 1998

An algorithm of Thermal-elastohydrodynamic lubrication analysis for the piston ring is developed. This algorithm contains cavitation boundary condition so it automatically satisfies conservation of mass. 1-D Reynolds equation and 2-D energy equation are solved simultaneously by using Gauss-Jordan method and Newton-Raphson method. Minimum film thickness and friction force are calculated for 1 cycle. There is little difference between the results caculated by isothermal rigid and EHL analysis in entire cycle. In the results of THL, shear heating effect and temperature boundary condition affect the minimum film thickness and friction force prediction. The minimum film thickness and the friction force calculated by THL are lower than those caculated using isothermal assumption.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.12
• /
• pp.1841-1851
• /
• 1990

Self-aligned gate GaAs MESFETs using ion beam deposited tungsten applicable to GaAs LSI fabrication process have been fabricated. Silicon implanted samples were annealed using isothermla two step RTA process and conventional one step RTA process. The electrical and physicla characteristics of annealed samples were investigated using Hall and I-V measurements. As results of measurements, activation characteristics of the isothermal two step RTA process are better than those of one step annealed ones. Using the developed processes, GaAs SAFETs (Self-Aligned Gate FET) have been fabricated and electdrical characteirstics are measured. As results, subthreshold currents of SAGFETs are 6x10**-10 A/\ulcorner, that is compatible to conventional MESFET, maximum transconductances of 0.75\ulcorner gate MESFET using one step RTA process and 2\ulcorner gate MESFET using isothermal two step RTA process are 18 mS/mm, 41 mS/mm respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.731-734
• /
• 2001

A cryogenic stirling cooler is currently under development at Korea Institute of Industrial Technology(KITECH). Cryocooler has many kinds of types. The stirling cooler is the most appropriate one for under 80K with the trait of long life cycle and small size. The stirling cooler uses helium as a working fluid. Helium is pressurized by the linear compressor which is driver by linear motor. In this paper, the change of pressure and volume is studied by the isothermal analysis method. It is necessary to investigate the optimized pressure to meets the highest COP. The compressor's piston and expender's displacer interact according to the working fluid's pressure level and the phase difference. This paper presents the relation between the initial pressure and the work of cryocooler. By that results, we can predict the performance of linear compressor.

• Fibers and Polymers
• /
• v.2 no.2
• /
• pp.75-80
• /
• 2001

The thermal degradation of poly(ethylene terephthalate-co-isophthalate)s (PETIs) is investigated by using isothermal thermogravimetric analysis at the temperature range of 280-31$0^{\circ}C$. The degradation rate of PETIs is increased as the mole ratio of ethylene isophthaloyl (EI) units in PETIs increases. The activation energies for the thermal degradation of poly(ethylene terephthalate), PETI(5/5), and poly(ethylene isophthalate) are 33.4, 16.6, and 8.9 kcal/mole, respectively. The degradation rate of PETIs is influenced by their volatile cyclic oligomer components formed during the polymerization and the thermal degradation. It is simulated by the rotational isomeric state model that the content of cyclic dimer in PETIs, which is the most volatile cyclic oligomer component, increases with the EI units in PETIs.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.67.1-67.1
• /
• 2010

Understanding the nature of MHD turbulence is of fundamental importance in astrophysics. The results of these studies can be used to develop the star formation theory. While most of previous studies have considered turbulence in uniform media, the stratification of media can play an important role. We performed three-dimensional numerical simulations of isothermal, compressible, MHD turbulence with different plasma beta's and different flow Mach numbers in stratified media to study the effects of stratification on turbulence. We found Statistics of turbulent flow in stratified media is different from in uniform media. In this talk, we present the statistical properties of the MHD turbulence, such as the PDF, power spectrum, and structure function.