• Smart Structures and Systems
• /
• v.12 no.3_4
• /
• pp.251-269
• /
• 2013

Measurement of deflections of certain bridges is usually hampered by corruption of the GPS signal by multipath associated with passing vehicles, resulting to unrealistically large apparent displacements. Field data from the Gorgopotamos train bridge in Greece and systematic experiments revealed that such bias is due to superimposition of two major effects, (i) changes in the geometry of satellites because of partial masking of certain satellites by the passing vehicles (this effect can be faced with solutions excluding satellites that get temporarily blocked by passing vehicles) and (ii) dynamic multipath caused from reflection of satellite signals on the passing trains, a high frequency multipath effect, different from the static multipath. Dynamic multipath seems to have rather irregular amplitude, depending on the geometry of measured satellites, but a typical pattern, mainly consisting of a baseline offset, wide base peaks correlating with the sequence of main reflective surfaces of the vehicles passing next to the antenna. In cases of limited corruption of GPS signal by dynamic multipath, corresponding to scale distortion of the short-period component of the GPS waveforms, we propose an algorithm which permits to reconstruct the waveform of bridge deflections using a weak fusion of GPS and RTS data, based on the complementary characteristics of the two instruments. By application of the proposed algorithm we managed to extract semi-static and dynamic displacements and oscillation frequencies of a historical railway bridge under train loading by using noisy GPS and RTS recordings. The combination of GPS and RTS is possible because these two sensors can be fully collocated and have complementary characteristics, with RTS and GPS focusing on the long- and short-period characteristics of the displacement, respectively.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.9-12
• /
• 2001

Composite materials can be used economically and efficiently in broad civil engineering applications when standards and processes for analysis, design, fabrication, construction and quality control are established. Many of the bridge systems, including the girders and cross-beams, and concrete decks behave as the special othotropic plates. Such systems with boundary conditions other than Navier or Levy solution types, or with irregular cross sections, analytical solution is very difficult to obtain. Numerical method for eigenvalue problems are also very much involved in seeking such a solution. A method of calculating the natural frequency corresponding to the first mode of vibration of beam and tower structures with irregular cross-sections was developed and reported by the author in 1974 Recently, this method was extended to two dimensional problems including composite laminates, and has been applied to composite plates with various boundary conditions with/without shear deformation effects and reported at several international conferences including the Eighth Structures Congress of American Society of Civil Engineers in 1990. In this paper, the result of application of this method to the special orthotropic plates with various boundary condition is presented.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.11
• /
• pp.171-179
• /
• 1997

This paper describes a nesting system of a computer-aided design of blanking and piercing for irregularly shaped sheet metal products. An approach to the system is based on knowledge-based rules. A nesting system is designed by considering several factors, such as utilization ratio which minimises the scrab for single or pairwise operation, bridge width, grain orientation and design requirements which maximise the strength of the part when subsequent bending is involve. Therefore this system which was implemented blank layout and strip layout module can carry out a nesting with a best utilization and a process planning for irregular shaped sheet metal products in single or pairwise operation and generate the blank layout and strip layout in graphic forms. Knowledges for a nesting and a process planning are extracted from plasticity theories, relevant references and empirical know-hows of experts in blanking industries. This provides its efficiency and effectiveness for nesting irregularly shaped sheet metal products.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.2
• /
• pp.124-133
• /
• 1998

This paper describes a research work of developing a computer-aided design of blanking and piercing for irregular-shaped sheet metal products. An approach to the development of compact and practical CAB system is based on the knowledge-based rules. Knowledge for the CAD system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system has been written in AutoLISP on the AutoCAD with a personal computer. Based on knowledge-based rules, the system, STRT-DES, is designed by considering several factors, such as complexities of blank geometry and punch profile, availability of press equipment and standard parts, utilization ratio which minimizes the scrap in a single or a pairwise operation, bridge width, grain orientation and design requirements which maximize the strength of the part when subsequent bending is involved. This system checks a forming feasibility with both internal and external features, a dimension of blanked hole, and a corner and a fillet radius for irregualrly shaped sheet metal products. Therefore this system can carry out a die design for each process which is obtained from results of an automated blank layout drawing with a best utilization ratio for irregular shape of product that was successful in production feasibility check module and those of an automated strip layout drawing and generate part drawings and the assembly drawing of die set in graphic forms.

• Advances in Computational Design
• /
• v.2 no.1
• /
• pp.15-28
• /
• 2017

One of the major developments in seismic design over the past few decades is the increased emphasis for limit states design now generally termed as Performance Based Engineering. Performance Based Seismic Design (PBSD) uses Displacement Based Design (DBD) methodology wherein structures are designed for a target level of displacement rather than Force Based Design (FBD) methodology where force or strength aspect is being used. Indian codes still follow FBD methodology compared to other modern codes like CalTrans, which follow DBD methodology. Hence in the present study, a detailed review of the two most common design methodologies i.e., FBD and DBD is presented. A critical evaluation of both these methodologies by comparing the seismic performance of bridge models designed using them highlight the importance of adopting DBD techniques in Indian Standards also. The inherent discrepancy associated with FBD in achieving 'seismic regularity' is highlighted by assessing the seismic performance of bridges with varied relative height ratios. The study also encompasses a brief comparison of the seismic design and detailing provisions of IRC 112 (2011), IRC 21 (2000), AASHTO LRFD (2012) and CalTrans (2013) to evaluate the discrepancies on the same in the Indian Standards. Based on the seismic performance evaluation and literature review a need for increasing the minimum longitudinal reinforcement percentage stipulated by IRC 112 (2011) for bridge columns is found necessary.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.21 no.2
• /
• pp.611-616
• /
• 1994

A major cause of missing permanent incisors is congenital abscence and extraction because of trauma and pathologic condition. The request for restoration of missing or spaced anterior teeth is common in dental practice. Problems, such as the tilting, drifting, and rotation of teeth adjacent to the space, complicate the restoration of apperance, and a normally simple restorative dental procedure may become difficult. There are two primary treatment alternatives to improving a dentition's irregular and spaced apperance-closing the space by orthodontic means or providing a prosthesis to disguise the space. The treatment choice depends on many variables, but, as a general rule, patients with a normal overbite, overjet, and buccal relationship are better treated by maintaining the sapce and providing a prosthesis, either fixed or removable. This case report presents two cases : Traumatic loss of maxillary right and left central incisors, Extraction of malformed mandibular right central inciosr. The loss of central incisor space was regained by the fixed-removable and fixed orthodontic appliance, and then Maryland bridge was cemented.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.2 no.3
• /
• pp.42-47
• /
• 2011

A method of calculating natural frequencies corresponding to the modes of vibration of beams and tower structures with irregular cross sections and arbitrary boundary conditions was developed. The result is compared with that of the beam theory. Finite difference method is used for this purpose. The influence of the $D_{22}$ stiffness on the natural frequency is rigorously investigated. In this paper, the relation between the applied loading sizes and the natural frequency of vibration of some structural elements is presented. The results of application of this method to steel bridge and reinforced concrete slab bridge by using specially orthotropic plate theory is presented.

• Earthquakes and Structures
• /
• v.20 no.4
• /
• pp.389-403
• /
• 2021

Skewed bridges, being irregular structures with complicated dynamic behavior, are more susceptible to earthquake damage. Reliable seismic-resistant design of skewed bridges can be achieved by accurate determination of nonlinear seismic demands. However, the effect of geometric characteristics on the response modification factor (R-factor) is not accounted for in bridge design practices. This study attempts to investigate the effects of changes in the number of spans, skew angle and bearing stiffness on R-factor values and to assess the seismic fragility of skewed bridges. Results indicated that changes in the skew angle had no significant effect on R-factor values which were in consonance with code-prescribed R values. Also, unlike the increase in the number of spans that resulted in a decrease in the R-factor, the increase in bearing stiffness led to higher R-factor values. Findings of the fragility analysis implied that although the increase in the number of spans, as well as the increase in the skew angle, led to a higher failure probability, greater values of bearing stiffness reduced the collapse probability. For practicing design engineers, it is recommended that maximum demands on substructure elements to be calculated when the excitation angle is applied along the principal axes of skewed bridges.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.77-84
• /
• 2007

In this paper presented, a design method of sandwich slab bridge of simple supported made by composite materials. Many of the bridge systems, including the girders and cross-beams, and concrete decks behave as the special orthotropic plates. Such systems with sections, boundary conditions other than Navier or Levy solution types, or with irregular cross sections, analytical solution is very difficult to obtain. Thus, Finite Difference Method is used for analysis of the pertinent problem. For the design of bridge made by the composite materials, cross-section is used the form-core shape because of this shape is economical and profitable, and for output of the stress value used F.D.M. Based the experimental of a composite specialist, an equation expressing the rate of decrease of tensile strength of glass fibers based on increase of mass was obtained. From these equations, one can estimate the rate of tensile strength reduction due to increased size. Tasi-Wu failure criterion for stress space is used. Strength-failure analysis procedure, using these reduced tensile strength, is presented.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.113-117
• /
• 2004

Such social structures as bridges, buildings, dams and towers have been transformed by their own load or fundamental ground. They have been behaved by other external causes. These regular or irregular behaviors threaten to do their users safety. Therefore, to monitor the load of the structures or reaction shown by them could help to verify their behaviors. RTK GPS allows the use of a static base station and remote rover unit to allow for data collection within several seconds and in real time. It is useful for monitoring the behaviors of massive structures like bridges. In this Study, Among GPS methods, we used RTK GPS to analyze the precision of monitoring and then on the basis of it, we developed a monitoring system using RTK GPS when measured the behavior of main tower of a suspension bridge by using RTK GPS. Comparing a deviation between observation values, X axis was 1mm, Y axis was 1mm and Z axis 2.2mm. It turned out that it was possible to monitor and measure structures by RTK GPS.