• 한국해양공학회지
• /
• 제16권1호
• /
• pp.64-70
• /
• 2002

This paper shows the results of the development of a small size of digital type continuous and intermittent welding auto-carriage based on microprocessor (Intel 80196KC) for welding process with long welding line. The developed welding auto-carriage loads welding torch and tracks welding line. It is an automaton largely used for welding process with a lot of long welding lines such as shipbuilding and structure. Most traditional auto-carriages have been developed based on analog circuit for open loop control. So this analog circuit welding auto-carriage cannon control welding speed. Specially welding auto-carriage for intermittent welding condition is so complicated and has the low precision of control performance in welding distance and non-welding distance. The auto-carriage developed in this paper has the following characteristics: It has not only functions of traditional carriage but also functions such as pseudo-welding process of big iron structures, intermittent welding in order to limit heat for welding thin plates, crater treatment of the final step of welding, acceleration at the initial step of welding and deceleration in the final step of welding. The main control board of auto-carriage, power supply system and DC motor drive wee developed and manufactured. The welding speed and the welding distance of the developed auto-carriage are controlled accurately by feedback control using photo-sensor. Hardware and software robust against the heat and noise produced on the welding process are developed.

• 한국정밀공학회지
• /
• 제20권12호
• /
• pp.126-134
• /
• 2003

In order to investigate the effect of surface treatment in Aluminium alloy and Titanium alloy which are used to armor material during ballistic impact, a ballistic testing was conducted. Anodizing was used to achieve higher surface hardness of Aluminium alloy and Iron plating in PVD(Physical Vapor Deposition) method was used to achieve higher surface hardness of Titanium alloy. Surface hardness test were conducted using a Micro victor's hardness tester. Ballistic resistance of these materials was measured by protection ballistic limit(V-50), a statical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed from the results of V-50 test and Projectile Through Plates (PTP) test at velocities greater than V-50. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature using 5.56mm ball projectile. V-50 tests were conducted with 0$^{\circ}$obliquity at room temperature with projectiles that were able to achieve near or complete penetration during PTP tests. Surface hardness, resistance to penetration. and penetration modes of surface treated alloy laminates are compared to those of surface non-treated alloy laminates. A high speed photography was used to analyze the dynamic perforation phenomena of the test materials.

• 동력기계공학회지
• /
• 제4권4호
• /
• pp.32-40
• /
• 2000

A study on the fluid flow with ultrasonic forcing was carried out to get the enhancement of turbulence by laying emphasis on the ultrasonic incidence angles and reflectors. A large water tank was made of the transparent acrylic plates and city water of $25^{\circ}C$ was used as working fluid. 7 angles ($30^{\circ},\;45^{\circ},\;60^{\circ},\;90^{\circ},\;120^{\circ},\;135^{\circ},\;150^{\circ}$) as the ultrasonic incidence angle and 4 materials (wood, acryl, glass, iron) as the reflector were selected arid experiments for the above were made. The velocity vector distribution, kinetic energy and turbulence intensity of the turbulence flow fields enhanced by ultrasonic forcing were measured, compared and discussed by using the PIV measurement which was possible to measure the velocities of simultaneous multipoints. In results, it was cleared that the incidence angle of ultrasonic and material of reflector influenced the enhancement of turbulence.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 2002년도 춘계공동학술대회
• /
• pp.109-113
• /
• 2002

Steel industry is the most capital intensive and the largest energy consuming industry, which operate huge and complex facilities to supply various steel products as the primary materials to almost every manufacturing industry Major steel products are hot-rolled and cold-rolled coils, plates, and wires that are produced through molten iron making, molten steel making, casting, and rolling. Each process runs in batch between setups and the specifications or bach are different with each other High energy consuming and heavy material handling require careful synchronization or processes, as well. Considering the synchronization or processes, the lot planning and scheduling problem in the integrated steelmaking process rovers the roll grouping with given casts. the sequencing or rolls over time, and the machine assignment and time scheduling or charges and casts. The problem is investigated by dividing it into two cases whether single or parallel machines at the molten steel making and the continuous casting processes. Problem descriptions and solution approaches or each instance are introduced. To test their performance and conformity, implementation or the algorithms and numerical experiments are carried out with real world and constructed data sets.

• 한국군사과학기술학회지
• /
• 제19권5호
• /
• pp.629-637
• /
• 2016

This paper presents a ballistic limit velocity measurement using the support vector machine that classifies two classes, the partial penetration and the complete penetration, by generating a linear separating hyperplane that equally divides the classes. For the ballistic limit velocity measurement, the previous methods(MIL-STD-662F and NIJ-STD-0101.06) have required a large number of experiments that caused high cost and time. However, the proposed method is not only flexible, requiring 0.85 ~ 4.8 times fewer experiments but also reliable, providing less than 2 % difference in results compared to the previous methods. For its validation, live fire experiments were conducted using various thickness SS400 iron plates as a target and two different types of live bullets such as 5.56 mm M193 and 7.62 mm M80.

• Geomechanics and Engineering
• /
• 제13권6호
• /
• pp.1027-1044
• /
• 2017

Membrane penetration is the most important factor influencing the measurement of volume change for triaxial consolidated-drained shear test for coarse-grained soil. The effective pressure p, average particle size $d_{50}$, thickness $t_m$ and elastic modulus $E_m$ of membrane, contact area between membrane and soil $A_m$ as well as the initial void ratio e are the major factors influencing membrane penetration. According to the membrane deformation model given by Kramer and Sivaneswaran, an analytical solution of the membrane penetration considering the initial void ratio is deduced using the energy conservation law. The basic equations from theory of plates and shells and the elastic mechanics are employed during the derivation. To verify the presented solution, isotropic consolidation tests of a coarse-grained soil are performed by using the method of embedding different diameter of iron rods in the triaxial samples, and volume changes due to membrane penetration are obtained. The predictions from presented solution and previous analytical solutions are compared with the test results. It is found that the prediction from presented analytical solution agrees well with the test results.

• 보존과학회지
• /
• 제20권
• /
• pp.9-22
• /
• 2007

문화재의 생물방제를 목적으로 개발되어 시판되고 있는 3종의 식물 추출 천연 살충 살균제에 대한 문화재의 재질에 미치는 영향을 평가하였다. 평가 대상 재질은 1) 견직물 : 염색하지 않은 견직물, 황벽, 오배자, 오배자(명반 후매염), 오배자(녹반 후매염), 치자, 울금, 도토리, 도토리(녹반 후매염), 자초, 천근, 천근(명반 후매염), 홍화(홍염색), 소목, 소목(명반 선매염, 후매염) 염색 및 쪽, 쪽과 황벽 복염, 쪽과 소목 복염 견직물 2) 면직물 : 염색하지 않은 면직물, 황벽, 오배자, 오배자(명반 후매염), 치자, 도토리, 도토리(녹반 후매염), 자초, 천근, 천근(명반 후매염), 홍화(홍염색), 소목, 소목(명반선매염, 후매염) 염색 및 쪽, 쪽과 소목 복염 면직물, 3) 염색하지 않은 저마직물 4) 한지 : 염색하지 않은 한지, 소목, 쪽, 치자, 홍화(홍염색), 황벽 염색 한지 5) 안료분말 :석청 석록, 연단, 석간주, 주사, 주, 패각호분, 밀타승,대자, 석황, 쪽, 백토, 연백 남전 5)채색편 : 석청, 석록, 연단, 석간주, 주사, 주, 패각호분, 밀타승, 대자, 석황, 쪽, 백토, 연백, 남전이다. 시험은 시료를 습도 $55{\pm}1%$. 온도 $20{\pm}2^{\circ}C$의 환경에서 약제의 권장 농도의 10배에 9개월간 노출 시킨 후 기준 시료와의 색차와 인장강도를 비교 평가하였다. 약제 노출 후 염색을 하지 않은 견직물 면직물 저마직물 한지는 약제에 의한 색상 변화는 거의 일어나지 않았으나, 염색 견직물 면직물 한지는 도토리나 천근 염색 직물 등이나 치자 염색 한지를 제외하고는 대부분 일반인도 인식이 가능한 뚜렷한 색상차가 발생하였다. 특히 울금 염색 견직물은 가장 색상차가 뚜렷하였다. 그리고 안료분말이나 채색편은 납, 구리, 비소, 수은 함유 안료 및 식물성 안료 등에서 뚜렷한 색상차가 발생하였다. 인장강도는 염색하지 않은 견직물은 약제에 거의 변화가 없으며 면직물은 약간 감소하는 경향을 보이나, 염색을 한 견직물이나 면직물은 강도의 증가나 감소가 뚜렷하였다. 특히 천근 염색 견직물은 10% 이상의 강도 감소가, 쪽 염색 견직물은 10% 이상의 강도 증가가 일어났으며, 천근과 소목(명반 후매염) 염색 면직물은 10% 이상의 강도 감소 현상이 일어났다.

• 한국산학기술학회논문지
• /
• 제18권12호
• /
• pp.106-111
• /
• 2017

본 연구에서는 해양구조물의 상부(top side) 구조물을 설치할 때 필요한 장치인 LMU(Leg Mating Unit)의 강성을 구조해석을 통하여 검토하였다. 이것은 구조물의 지지 점에 장착되어 설치 시 충격을 흡수하고 안정적으로 구조물을 지지하는 데 사용된다. LMU는 가운데가 비어있는 원통형 구조로서 수직 하중을 지지하기 위해서 일래스토머릭 베어링(Elastomeric Bearing, 이하 EB)과 철판을 여러 층으로 적층한다. EB의 강성은 기본적으로 베어링의 크기에 영향을 받지만, 동일한 크기에서도 내부 보강판의 적층 수에 따라 강성이 변하게 된다. 일반적으로 보강판과 압축 강성 사이의 관계를 분석하여 적합한 설계를 한다. EB의 강성은 변위를 제어하면서 반력을 산출하는 방식으로 분석을 한다. 먼저 보강판의 크기와 압축 강성 관계를 검토하고, 보강판의 적층 수와 압축 강성 관계를 검토한다. LMU는 장착되는 지점마다 다른 하중이 요구된다. 해석을 통해 각 지점에서 동일한 변형이 발생하도록 압축 강성을 다르게 설계하는 것이 목표이다. 본 연구의 유한요소해석을 위하여 상용 프로그램인 ANSYS를 이용하였다.

• 한국문화재보존과학회:학술대회논문집
• /
• 한국문화재보존과학회 2004년도 제20회 발표논문집
• /
• pp.15-24
• /
• 2004

The Seokgatap pagoda composed of mainly alkali granite and other minor pink-feldspar granite, fine-grained granite, granodiorite, diorite, gabbro, and tuff. Despite the small loss and damage derived from joints, its peel-off and exfoliation are serious enough to cause the heavy deterioration on the stone surface. The chemical and petrological weathering has partly replaced the original rock-forming minerals with clay minerals and iron oxyhydroxides. Based on the petrogenesis, rock materials of the pagoda is very similar to rocks of Dabotap pagoda and the Namsan granite in the Gyeongju. The central fart of the pagoda has sunken highly, which caused all the corners to split and the structural transformation to become worse. The reverse V-shaped gaps between the materials have broken stones filled in a coarse way. The iron plates inserted between the upper flat stone laid on other stones and tile pagoda body in the north and east side has been exposed in the air and corroded, discoloring of the adjacent stones. The overall diagnosis of the Seokgatap pagoda is the deteriorated functions of the stone materials, which calls for a long-term monitoring and plans to reinforce the stone surfaces. But the main body including the pagoda roof stone needs washing on a regular basis, and the many different cracks should be fixed with glue by using the fillers or hardeners designed for stone cultural properties after removing the cement mortar. In case of the replacement of the stone materials with new stones, it's necessary to examine the pagoda for the center of gravity and support intensity of the materials. The structural stability of the pagoda can be attained by taking a reinforce measure in geotechnical engineering and making a drainage. The ground humidity, which has aggravated weathering and structural instability, should be resolved by setting up a humidity reduction facility. The contamination of lichens and bryophyte around the pagoda and on the surface is serious. Thus biochemical treatments should be given too in order to prevent further biological damages and remove the vegetation growing on the discontinuous planes.

• 한국산업융합학회 논문집
• /
• 제6권1호
• /
• pp.81-86
• /
• 2003

For the simultaneous removal of $SO_2$/NOx from an iron-ore sintering plant, industrial plasma experiments have been conducted with a flue gas flow rate of $5,000Nm^3/hr$. The maximum 40kW power using the magnetic pulse compression (MPC) system generates a peak value of 100-150kV pulse voltage with its risetime of 200nsec and full width at half maximum (FWHM) of 500nsec, and with a frequency <300Hz. The plasma reactor module adopts a wire-plate structure with a gap of 200-400mm ID between plates. Initial concentrations of $SO_2$ and NOx were around 100-150ppm, respectively in the presence of 15% $O_2$ and <10% $H_2O$. Various reaction parameters such as specific energy ($Whr/Nm^3$), $NH_3$ injection with corona discharge, flow rate and injection of hydrocarbons were investigated for $SO_2$/NOx removal characteristics. About 90/65% of $SO_2$/NOx were simultaneously removed with a specific energy of $3.0Whr/Nm^3$ when both $NH_3$ and hydrocarbons were injected. Practical implications that the pilot-scale plasma results provide are further discussed.