• 마이크로전자및패키징학회지
• /
• 제28권2호
• /
• pp.29-37
• /
• 2021

3 차원 패키징을 위한 저온 Cu-Cu직접 접합부의 계면접착에너지를 향상시키기 위해 Cu박막 표면에 대한 Ar/N₂ 2단계 플라즈마 처리 전, 후 Cu표면 및 접합계면에 대한 화학결합을 X-선 광전자 분광법(X-ray photoelectron spectroscopy)을 통해 정량화한 결과, 2단계 플라즈마 처리로 인해 Cu표면에 Cu₄N이 형성되어 Cu산화를 효과적으로 억제하는 것을 확인하였다. 2단계 플라즈마 처리하지 않은 Cu-Cu시편은 표면 산화막의 영향으로 접합이 제대로 되지 않았으나 2단계 플라즈마 처리한 시편은 효과적인 표면 산화방지효과로 인해 양호한 Cu-Cu접합을 형성하였다. Cu-Cu직접접합 계면의 정량적 계면접착에너지를 double cantilever beam 시험방법 및 4점 굽힘(4-point bending, 4-PB) 시험방법을 통해 비교한 결과, 각각 1.63±0.24, 2.33±0.67 J/m²으로 4-PB 시험의 계면접착에너지가 더 크게 측정되었다. 이는 계면파괴역학의 위상각(phase angle)에 따른 계면접착에너지 증가 거동으로 설명할 수 있는데 즉, 4-PB의 계면균열선단 전단응력성분 증가로 인한 계면거칠기의 효과에 기인한 것으로 판단된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.968-970
• /
• 1999

The trend of increasing of portable electric devices and demand for global environmental conservation have demands the development of high energy density rechargeable batteries. Lithium polymer battery has excellent theoretical energy density and energy conversion efficiency. Lithium polymer battery, included solid polymer electrolyte(SPE), can be viewed as a system suitable for wide applications from thin film batteries for microelectronics to electric vehicle batteries. The purpose of this paper is to research and development of flyash anode for lithium polymer battery. We investigated AC impedance response and charge/discharge characteristics of flyash/SPE/Li cells. The radius of semicircle associated with the interfacial resistance of flyash/SPE/Li cell increased very slowly during discharge process from 3.11V to 0.478V. And then the cell resistance was decreased at discharge process from 10% SOC to 0% SOC. Also, The radius of semicircle associated with the interfacial resistance of flyash/SPE/Li cell decreasing very slowly during charge process. And then the cell resistance was increased after 20th discharge precess. The discharge capacity based on flyash of 1st and 20th cycles was 276mAh/g and 143mAh/g.

• Nuclear Engineering and Technology
• /
• 제29권1호
• /
• pp.45-57
• /
• 1997

The direct contact condensation phenomenon, which occurs when steam is injected into the subcooled water, has been experimentally investigated. Two plume shapes in the stable condensation regime are found to be conical and ellipsoidal shapes depending on the steam mass flux and the liquid subcooling. Divergent plumes, however, are found when the subcooling is relatively small. The measured expansion ratio of the maximum plume diameter to the injector inner diameter ranges from 1.0 to 2.3. By means of fitting a large amount of measured data, an empirical correlation is obtained to predict the steam plume length as a function of a dimensionless steam mass flux and a driving potential for the condensation process. The average heat transfer coefficient of direct contact condensation has been found to be in the range 1.0~3.5 ㎿/$m^2$.$^{\circ}C$. Present results show that the magnitude of the average condensation heat transfer coefficient depends mainly on the steam mass fin By using dynamic pressure measurements and visual observations, six regimes of direct contact condensation have been identified on a condensation regime map, which are chugging, transition region from chugging to condensation oscillation, condensation oscillation, bubbling condensation oscillation, stable condensation, and interfacial oscillation condensation. The regime boundaries are quite clearly distinguishable except the boundaries of bubbling condensation oscillation and interfacial oscillation condensation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.61-61
• /
• 2010

In the present work, we present the optimized the hybrid structures of carbon nanotubes (CNTs) and metal nanocomposites including Cu, Al, Co and Ni using the first principle calculations based on the density functional theory. Introduction of CNTs into a metal matrix has been considered to improve the mechanical properties of the metal matrix. However, the binding energy between metals and pristine CNTs wall is known to be so small that the interfacial slip between CNTs and the matrix occurs at a relatively low external stress. The application of defective or functionalized CNTs has thus attracted great attention to enhance the interfacial strength of CNT/metal nanocomposites. Herein, we design the various hybrid structures of the single wall CNT/metal complexes and characterize the interaction between single wall CNTs and various metals such as Cu, Al, Co or Ni. First, differences in the binding energies or electronic structures of the CNT/metal complexes with the topological defects, such as the Stone-Wales and vacancy, are compared. Second, the characteristics of functionalized CNTs with various surface functional groups, such as -O, -COOH, -OH interacting with metals are investigated.We found that the binding energy can be enhanced by the surface functional group including oxygen since the oxygen atom can mediate and reinforce the interaction between carbon and metal. The binding energy is also greatly increased when it is absorbed on the defects of CNTs. These results strongly support the recent experimental work which suggested the oxygen on the interface playing an important role in the excellent mechanical properties of the CNT-Cu composite[1].

• 접착 및 계면
• /
• 제22권4호
• /
• pp.113-117
• /
• 2021

차세대 태양전지 중 유기물을 활용하는 유기 태양전지는 미래 핵심 에너지 생산 장치로, 최근 급격한 성장세와 함께 많은 주목을 보이고 있다. 유기 태양전지 효율 향상을 위해서 계면 공학 기술이 많이 응용되고 있다. 특히 양전극인 양극과 음극에 계면 공학을 활용하여 에너지 준위 조절을 통한 소자 효율 향상과, 궁극적으로 적층형 유기 태양전지에 계면 공학을 활용하여 우수한 전기적, 광학적 성능을 이끌어 내어 고성능 소자를 제작하는 방식이 널리 활용되고 있다. 본 총설에서는 유기태양전지에 활용되고 있는 계면 공학에 대하여 최근 연구 동향을 요약 및 소개하고 고성능 유기 태양전지 제작 방식에 대하여 논의하고자 한다.

• Journal of Electrochemical Science and Technology
• /
• 제9권4호
• /
• pp.330-338
• /
• 2018

The adhesion strength as well as the electrochemical properties of $LiNi_{0.4}Mn_{0.4}Co_{0.2}O_2$ electrodes containing various conductive carbons (CC) such as fiber-like carbon, vapor-grown carbon fiber, carbon nanotubes, particle-like carbon, Super P, and Ketjen black is compared. The morphological properties is investigated using scanning electron microscope to reveal the interaction between the different CC and the active material. The surface and interfacial cutting analysis system is also used to measure the adhesion strength between the aluminum current collector and the composite film, and the adhesion strength between the active material and the CC of the electrodes. The results obtained from the measured adhesion strength points to the fact that the structure and the particle size of CC additives have tremendous influence on the binding property of the composite electrodes, and this in turn affects the electrochemical property of the configured electrodes.

• Composites Research
• /
• 제24권6호
• /
• pp.12-17
• /
• 2011

자체-센서와 미세 작동기 응용을 위한 CNT와 ITO로 코팅된 나노복합재료의 계면접착 내구성과 전기적 특성을 평가하였다. 나노복합재료의 접착 및 계면 내구성은 반복하중 피로시험에 따른 전기저항도를 측정하여 평가하였다. CNT와 ITO의 고유 전기적 특성으로 인하여 CNT가 코팅된 PVDF 나노복합재료는 ITO가 코팅된 경우보다 다소 낮은 전기저항도를 나타내었으나, 모두 양호한 자체-감지능을 보여주었다. CNT/PVDF와 ITO/PVDF 나노복합재료 모두 계면 내구성은 양호함을 확인하였다. 정적 접촉각 시험을 통해 CNT와 ITO 그리고 PVDF간의 표면에너지, 접착일, 그리고 퍼짐계수를 평가하여 계면 내구성과 의 상호 관련성을 확인하였다. 수용액에서 CNT와 ITO로 코팅된 PVDF 시편의 최적의 작동성은 주파수와 전압을 달리하여 레이져 변위센서를 사용한 연신율 변화로 측정하였다. 작동된 두 나노복합재료들의 연신율은 주파수가 증가함에 따라 감소하며, 반면에 전압의 증가에 따라 상승하였다. 각 나노복합재료의 나노구조 및 고유의 전기적 특성으로 인하여, CNT/PVDF가 ITO/PVDF 보다 자체-감지 및 작동기로서 더 적합하다는 것을 알 수 있었다.

• 공업화학
• /
• 제32권3호
• /
• pp.260-267
• /
• 2021

본 연구에서는 코코넛 오일로부터 카르복실레이트계 음이온 계면활성제 SLEC-3을 합성하였으며, 합성된 계면활성제의 구조를 FT-IR, ¹H-NMR 및 ¹³C-NMR 분석을 통하여 확인하였다. 합성한 계면활성제 SLEC-3에 대하여 임계 마이셀 농도, 정적 및 동적 표면장력, 유화력, 거품 안정성 등의 계면 물성을 측정한 결과, 기존 세제 제품에서 널리 사용되는 음이온 계면활성제 SLES와 비교하여 계면 활성이 보다 우수하고 계면 에너지를 낮추는데 더 효과적이었다. 또한 SLCE-3에 대한 생분해성, 급성 경구 독성 및 급성 피부자극 시험을 실시한 결과, 저자극 및 저독성을 가지고 있기 때문에 세제 및 세정제 제품에 적용할 수 있을 것으로 판단되었다.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.468-475
• /
• 2012

A proper stacking force and assembly are important to the performance of fuel cell. Improper assembly pressure may lead to leakage of fuels and high interfacial contact resistance, excessive assembly pressure may result in damage to the gas diffusion layer and other components. The pressure distribution of gas diffusion layer is important to make interfacial contact resistance less for stack performance. To analyze the influence of design parameter factors for pressure distribution, and to optimize stack design, DOE (Design of Experiment) was used for polymer electrolyte membrane fuel cell stack pressure test. As commonly known, the higher clamping force improves the fuel cell stack performance. However, non-uniformity of stress distribution is also increased. It shows that optimization between clamping force and stress distribution is needed for well designed structure of fuel cell stack. In this study, stack design optimization method is suggested by using FEM (Finite Element Methode) and DOE for light-weighted fuel cell stack.

• Nuclear Engineering and Technology
• /
• 제52권1호
• /
• pp.59-68
• /
• 2020

ECCMIX component was introduced in RELAP5/MOD3 for calculating the interfacial condensation. Compared to other existing components in RELAP5, user experience of ECCMIX component is restricted to developmental assessment applications. To evaluate the capability of the ECCMIX component, ECCS experiment was conducted which included single-phase and two-phase thermal mixing. The experiment was carried out with test sections containing a main pipe (70 mm inner diameter) and a branch pipe (21 mm inner diameter) under the atmospheric pressure. The steam mass flow in the main pipe ranged from 0 to 0.0347 kg/s, and the subcooled water mass flow in the branch pipe ranged from 0.0278 to 0.1389 kg/s. The comparison of the experimental data with the calculation results illuminated that although the ECCMIX component was more difficult to converge than Branch component, it was a more appropriate manner to simulate interfacial condensation under two-phase thermal mixing circumstance, while the two components had no differences under single-phase circumstance.