• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1099-1101
• /
• 1999

PJB(Prefabricated Joint Box) is consisted of three major components ; an epoxy unit, a stress relief cone and a spring unit. The insulation structure of PJB is maintained by the interfacial pressure, and the dielectric performance at the interface depends on the interfacial pressure which is regarded as the most important factor for preventing breakdown failure. This experiment was performed to investigate breakdown voltage characteristic and partial discharge patterns under the controlled pressure conditions at the simulated interface. Finally, this paper presents the optimal pressure conditions at the interface by analyasing the PD patterns.

• Journal of the Korean Ceramic Society
• /
• v.32 no.11
• /
• pp.1262-1268
• /
• 1995

Photoelectrochemical properties of p-GaAs electrode have been investigated. I-V characteristic shows that the cathodic photocurrent is observed at -0.7 V vs. SCE. The photoresponse at near 870~880nm wavelength indicates that the photogenerated carriers contibuted to the observed current. The maximum converson efficiency of 35% is obtained for a Xe lamp light source at 400nm. In C-V relation, capacitance peaks appeared at the frequencies of 100Hz and 300Hz due to the activation of the interfacial states which exist at the energy level corresponding to the one-third of the GaAs band gap. The difference of about 1.1V between flatband potential (Vfb) from the Mott-Schottky method and onset voltage from I-V curve is observed due to the trap of carriers at the interfacial states in the boundary between GaAs and electrolyte. In case of WO3 deposited p-GaAs electrode, higher positive onset current and photocurent density are obtained. This can be explained by the fact that carriers are generated by light penetrated into the WO3 thin flm as well as p-GaAs substrate and then move into the electrolyte effectively.

• Composites Research
• /
• v.25 no.3
• /
• pp.70-75
• /
• 2012

Interfacial durability and electrical properties of CNT, ITO or xGnP coated PVDF nanocomposites were investigated for acoustic actuator applications. The xGnP coated PVDF nanocomposite exhibited better electrical conductivity than CNT and ITO case due to the unique electrical property of xGnP, and this nanocomposite also showed good sound characteristics. Interfacial adhesion durability between either neat CNT or plasma treated CNT and plasma treated PVDF were measured by static contact angle, surface energy, work of adhesion, and spreading coefficient tests. The optimum acoustic actuation performance of xGnP coated PVDF nanocomposite was measured using sound level meter with changing radius of curvature and coating conditions. As compared to CNT and ITO, the xGnP was known as more appropriate acoustic actuator due to the characteristic electrical property. It is the most appropriate condition when the radius of curvature is 15 degree. Although sound characteristics were different with various coating thicknesses, it is possible to manufacture transparent actuator with good sound quality.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.642-652
• /
• 2014

The synthesis of octenyl succinyl ${\beta}$-gucan (OSA-${\beta}$-glucan) was carried out and its interfacial properties at the oil-water interface and in emulsion systems were investigated. An aqueous ethanol system as a reaction media was used to facilitate the synthesis process; 10% (w/w) ethanol found to be the best as it showed a maximum degree of substitution (DS: 0.0132). FT-IR showed a characteristic absorption spectrum at $1736cm^{-1}$, indicating the esterification of octenyl succinyl groups to ${\beta}$-glucan backbone. As for interfacial tension measurements, it was decreased with increasing concentration of OSA-${\beta}$-glucan in the aqueous phase and when NaCl was added to aqueous OSA-${\beta}$-glucan solution in the range of 0.01 M to 0.1 M and also when pH was raised (pH 3 ~ pH 9). In systems of emulsion stabilized with OSA-${\beta}$-glucan, fat globule size found to decrease with increasing concentration of OSA-${\beta}$-glucan, showing a critical value of about $0.32{\mu}m$ at 0.5 wt%. When the OSA-${\beta}$-glucan emulsions were stored, it was found that fat globule size was increased with storage time and particularly pronounced increase was observed in emulsion with 1% OSA-${\beta}$-glucan, possibly due to depletion flocculation. Results of creaming stability evaluated by light scattering technique showed that it was more stable in emulsions containing smaller fat globule size. Surface load of OSA-${\beta}$-glucan in emulsions increased with increasing concentration of OSA-${\beta}$-glucan, suggesting a multilayer adsorption.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.4
• /
• pp.307-311
• /
• 1999

Interfacial properties of electrode and organic thin layer is one of the most important factor in performing a Light Emitting Diodes(LED). Phthalocyanine copper was used as a buffer layer to improve interface characteristic, so that device efficiency was improved. In this study, LEDs were fabricated as like structures of Indium-Tin-Oxide (ITO) / N,N' -Diphenyl-N,N'-di(m-tolyl)-benzidine (TPD) / 8-Hydroxyquinoline aluminum(Alq) / Aluminum(Al) and Indium-Tin-Oxide(ITO) / N,N'-Diphenyl-N,N' -di(m-tolyl)-benzidine(TPD) / 2-(4-Biphenylyl)-5(4-tert-butyl-phenyl)-1,3,4-oxadiazole(PBD) / Aluminum(Al). In these devices, CuPC was layered at electrode/organic layer interface. As position is changing and thickness is changing, devices showed characteristic luminescence efficiency and luminescence inensity respectively. We showed in this study that luminescence efficiency was improved with CuPC layer in LEDs. The efficiency of device with layer CuPC is higher than that of 2 layer CuPC. However, the luminescence of 2 layer CuPC device got higher value.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.1
• /
• pp.113-121
• /
• 1992

In this study, the variation of fatigue strength in CF/PEEK and CF/EPOXY, the matrix and interfacial strength of which differ from each other, has been studied from the viewpoint of microfracture behavior. The results obtained are as follows; According as the fatigue strength moves from the lower cycle range to the higher cycle range, that of CF/PEEK shows higher curve than that of CF/EPOXY does. In the early stage of fatigue life, the characteristic of fatigue crack in CF/PEEK is mainly the fracture of longitudinal fiber, while that in CF/EPOXY is the fracture of transverse fiber. The difference of fatigue strength in these materials can be explained by the fracture criteria of transverse fiber and longitudinal fiber.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.253-256
• /
• 2006

The HPFRCCs show the multiple crack and damage tolerance capacity due to the interfacial bonding of the fibers to the cement matrix. For practical application, it is needed to investigate the fractural behavior and of HPFRCCs and understand the micro-mechanism of cement matrix with reinforcing fiber. The objectives of this paper are to examine the compressive behavior, fracture and damage process of HPFRCC by acoustic emission technique. Total four series were tested, and the main variables were the hybrid type, polyethylene (PE) and steel cord (SC), and fiber volume fraction. The damage progress by compressive behavior of the HPFRCCs is characteristic for the hybrid fiber type and volume fraction. And from acoustic emission (AE) parameter value, it is found that the second and third compressive load cycles resulted in successive decrease of the ring-down count rate as compared with the first compressive load cycle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.7
• /
• pp.607-611
• /
• 2000

The characteristics on the interface between Epoxy and EPDM which are materials of the underground insulation systems of power delivery have studied. The breakdown strength of specimens are observed by applying high AC voltage at the room temperature. The breakdown times under the constant voltage below the breakdown voltage were gained. As constant voltage is applied the breakdown time is proportion to the breakdown strength. The life exponent n is gained by inverse power law and the long breakdown life time can be evaluated. AC breakdown strength and life time is improved by oiling to the interface. When the low viscosity oil is spread interface has the highest life time.

• Journal of Korea Multimedia Society
• /
• v.12 no.12
• /
• pp.1755-1760
• /
• 2009

In this research, for the first time, we tried to analyse Raman hyperspectral dentin data using Independent Component Analysis (ICA) to see its possibility of adoption for the dental analysis software. We captured hyperspectral dentin data on 569 spots on a molar with dental lesion by HR800 Micro Raman Spectrometer at UMKC-CRISP (University of Missouri at Kansas City-Center for Research on Interfacial Structure and Properties). Each spot has 1,005 hyperspectral data. We applied ICA to the captured hyperspectral data of dentin for evaluating ICA approach, and compared it with the well known multivariate analysis method, PCA. As a result of the experiment, ICA approach shows better local characteristic of dentin than the result of PCA. We confirmed that ICA also could be a good method along with PCA in the dental analysis software.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3971-3976
• /
• 2009

In this study, we secured wasted oyster shells as raw materials in order to applicate it to corrosion preventive ceramic coating reagent in the drinking water pipeline. Then, we investigated physicochemical properties in terms of basic calcination processing. Oyster shell was composed with 92.08% of $CaCO_3$ and the shapes of the pulverized particles were mostly oval. The calcined oyster shell showed increasing tendency of weight loss and of calcium content with the lapse of time and increase of temperature. The result indicates that the higher calcination processing temperature and the uniformly smaller particle size give more efficiency during calcination process. Therefore it is anticipated to be a good ceramic material to protect a surface of cleaning bed and inside of a tap water pipes from corrosion.