• 한국지반공학회논문집
• /
• 제28권3호
• /
• pp.45-54
• /
• 2012

최근 쓰레기 매립장에 널리 사용되고 있는 토목섬유는 흙과의 접촉면에서 대변형 거동 및 변형율 연화 등의 전단거동 특성을 보이는데, 이는 토목섬유-흙 접촉면에서 함수비, 연직응력, 화학적 요소의 영향 등 고유물성에 기인한다. 본 연구에서는 침출수 내의 산성 및 염기성과 같은 성분의 영향이 진동하중 상태에서 토목섬유-흙 접촉면의 전단강도 감소에 미치는 영향을 분석하였다. 이를 위하여 이미 구축된 다기능 접촉면 시험기(M-PIA)를 수정 제작하고 200일간 수침시킨 토목섬유와 흙 시료를 이용하여 진동 직접전단시험을 수행하였고, 그 결과 교란상태개념에 기초하여 화학적 인자들에 의한 토목섬유-흙 접촉면의 화학적 전단강도 감소 특성을 교란도 함수로써 확인하였다. 또한 전계방출주사현미경(FIB)을 이용하여 화학적 인자에 따른 흙입자 및 접촉면 손상의 차이를 확인하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.49-52
• /
• 2005

In the development of a propellant tank using liquid oxygen and liquid hydrogen, the improvement of microcrack resistance of carbon/epoxy composites is necessary for the application of a composite material to tank structures. In this research, two types of carbon/epoxy composites with different matrix systems were tested to measure interlaminar shear strength (ILSS), one of the material properties to evaluate fiber-matrix interface adhesion indirectly. Short beam specimens were tested inside an environmental chamber at room temperature(RT) and at cryogenic temperature( - 150 $^{\circ}C$) respectively. Results showed that the matrix system with large amount of bisphenol-A and CTBN modified rubber had good performance at cryogenic temperature.

• 한국지반환경공학회 논문집
• /
• 제3권2호
• /
• pp.15-21
• /
• 2002

건설공사에서 발생하는 환경문제에 대한 관심이 고조되는 가운데 기성 말뚝을 항타하는 과정에서 유발되는 소음, 진동문제를 해결하기 위해 저소음, 저진동 공법인 매입말뚝공법이 많이 적용되고 있다. 국내에서는 매입말뚝공법으로 SIP공법이 주로 사용되고 있다. 그러나 아직까지 SIP공법에 관한 합리적인 지지력 산정식이 제시되어있지 못한 실정이다. 이에 대해 본 연구에서는 SIP 말뚝의 주면저항력 특성을 고찰하여 이러한 문제점들을 개선, 보완하기 위하여 다양한 조건에서 SIP 말뚝 주면과 지반흙 사이의 경계면에 대하여 직접전단시험을 실시하였다. 그 결과를 토대로 통일분류상 SM, SC 지반에서의 SIP 말뚝 주면저항력 특성을 고찰하고 해당 지반에서 최대주면저항력 산정식을 제시하였다.

• 한국지반환경공학회 논문집
• /
• 제4권1호
• /
• pp.59-66
• /
• 2003

건설공사에서 발생하는 환경문제에 대한 관심이 고조되는 가운데 기성 말뚝을 항타하는 과정에서 유발되는 소음, 진동문제를 해결하기 위해 저소음, 저진동 공법인 매입말뚝공법이 많이 적용되고 있다. 국내에서는 매입말뚝공법으로 SIP공법이 주로 사용되고 있다. 그러나 아직까지 SIP공법에 관한 합리적인 지지력 산정식이 제시되어있지 못한 실정이다. 이에 대해 본 연구에서는 SIP 말뚝의 주면저항력 특성을 고찰하여 이러한 문제점들을 개선, 보완하기 위하여 다양한 조건에서 SIP말뚝 주면과 지반사이의 경계면에 대하여 직접전단 시험을 실시하였다. 시험 결과를 토대로 통일분류상 SM, SC 지반에서의 SIP말뚝 주면저항력 특성을 고찰하고 해당 지반에서 주면저항력 산정식을 제시하였다. 또한, 말뚝 경계요소의 저항력에 대한 새로운 비선형 수치 모델식과 계수산정식을 제안하였다.

• Computers and Concrete
• /
• 제26권2호
• /
• pp.151-159
• /
• 2020

This paper presents an evaluation of shear transfer across cracks in reinforced concrete through finite element modelling (FEM) and analytical predictions. The aggregate interlock is one of the mechanisms responsible for the shear transfer between two slip surfaces of a crack; the others are the dowel action, when the reinforcement contributes resisting a parcel of shear displacement (reinforcement), and the uncracked concrete comprised by the shear resistance until the development of the first crack. The aim of this study deals with the development of a 3D numerical model, which describes the behavior of Z-type push-off specimen, in order to determine the properties of interface subjected to direct shear in terms cohesion and friction angle. The numerical model was validated based on experimental data and a parametric study was performed with the variation of the concrete strength. The numerical results were compared with analytical predictions and a new equation was proposed to predict the maximum shear stress in cracked concrete.

• Computers and Concrete
• /
• 제24권3호
• /
• pp.207-222
• /
• 2019

This paper has presented an effective and accurate meso-scale finite element model for simulating the fracture process of concrete under compression-shear loading. In the proposed model, concrete is parted into four important phases: aggregates, cement matrix, interfacial transition zone (ITZ), and the initial defects. Aggregate particles were modelled as randomly distributed polygons with a varying size according to the sieve curve developed by Fuller and Thompson. With regard to initial defects, only voids are considered. Cohesive elements with zero thickness are inserted into the initial mesh of cement matrix and along the interface between aggregate and cement matrix to simulate the cracking process of concrete. The constitutive model provided by ABAQUS is modified based on Wang's experiment and used to describe the failure behaviour of cohesive elements. User defined programs for aggregate delivery, cohesive element insertion and modified facture constitutive model are developed based on Python language, and embedded into the commercial FEM package ABAQUS. The effectiveness and accuracy of the proposed model are firstly identified by comparing the numerical results with the experimental ones, and then it is used to investigate the effect of meso-structure on the macro behavior of concrete. The shear strength of concrete under different pressures is also involved in this study, which could provide a reference for the macroscopic simulation of concrete component under shear force.

• Structural Engineering and Mechanics
• /
• 제74권5호
• /
• pp.657-670
• /
• 2020

Due to the high compressive and tensile strength of ultra-high performance concrete (UHPC), UHPC used in steel concrete composite structures provided thinner concrete layer compared to ordinary concrete. This leaded to the headed stud shear connectors embedded in UHPC had a low aspect ratio. In order to systematic investigate the effect of headed stud with low aspect ratio on the structural behaviors of steel UHPC composite structure s this paper firstly carried out a test program consisted of twelve push out specimens. The effects of stud height, aspect ratio and reinforcement bars in UHPC on the structural behaviors of headed studs were investigated. The push out test results shows that the increasing of stud height did not obviously influence the structural behaviors of headed studs and the aspect ratio of 2.16 was proved enough to take full advantage of the headed stud strength. Based on the test results, the equation considering the contribution of weld collar was modified to predict the shear strength of headed stud embedded in UHPC. The modified equation could accurately predict the shear strength of headed stud by comparing with the experimental results. On the basis of push out test results, bending tests consisted of three steel UHPC composite slabs were conducted to investigate the effect of shear connection degree on the structural behaviors of composite slabs. The bending test results revealed that the shear connection degree had a significantly influence on the failure modes and ultimate resistance of composite slabs and composite slab with connection degree of 96% in s hear span exhibited a ductile failure accompanied by the tensile yield of steel plate and crushing of UHPC. Finally, analytical model based on the failure mode of composite slabs was proposed to predict the ultimate resistance of steel UHPC composite slabs with different shear connection degrees at the interface.

• Steel and Composite Structures
• /
• 제19권6호
• /
• pp.1403-1419
• /
• 2015

When precast concrete infill panels are connected to steel frames at discrete locations, interaction at the structural interface is neither complete nor absent. The contribution of precast concrete infill panels to the lateral stiffness and strength of steel frames can be significant depending on the quality, quantity and location of the discrete interface connections. This paper presents preliminary experimental and finite element results of an investigation into the composite behaviour of a square steel frame with a precast concrete infill panel subject to lateral loading. The panel is connected at the corners to the ends of the top and bottom beams. The Frame-to-Panel-Connection, FPC4 between steel beam and concrete panel consists of two parts. A T-section with five achor bars welded to the top of the flange is cast in at the panel corner at a forty five degree angle. The triangularly shaped web of the T-section is reinforced against local buckling with a stiffener plate. The second part consists of a triangular gusset plate which is welded to the beam flange. Two bolts acting in shear connect the gusset plate to the web of the T-section. This way the connection can act in tension or compression. Experimental pull-out tests on individual connections allowed their load deflection characteristics to be established. A full scale experiment was performed on a one-storey one-bay 3 by 3 m infilled frame structure which was horizontally loaded at the top. With the characteristics of the frame-to-panel connections obtained from the experiments on individual connections, finite element analyses were performed on the infilled frame structures taking geometric and material non-linear behaviour of the structural components into account. The finite element model yields reasonably accurate results. This allows the model to be used for further parametric studies.

• 한국산학기술학회논문지
• /
• 제17권4호
• /
• pp.400-413
• /
• 2016

80 MPa급 고강도 콘크리트가 강거더의 압축 플랜지로 대체하는 아중합성 거더의 경우, 플랜지와 케이싱 및 케이싱과 바닥판 2개의 접합부 계면이 형성되는데 각 계면의 수평 전단 저항능력은 구조물의 안전성에 있어 중요한 요소이다. 본 연구는 계면 상세를 달리한 6개의 실험체를 도로교설계기준(한계상태설계법)에 따라 설계 및 제작하여 이중합성 보의 휨 파괴 대비 수평 전단에 대한 구조 성능 실험을 수행하였다. 실험체의 주요변수로 스터드 전단연결재의 저항계수, 바닥판 콘크리트 및 철근의 재료저항계수, 콘크리트 인장강도에 따른 부착계수, 케이싱 콘크리트의 표면 상태 그리고 수평전단철근의 간격을 고려하였다. 실험 결과, 강재 상부 플랜지와 고강도 케이싱의 계면이 고강도 케이싱과 바닥판 계면 보다 결합성이 큰 것으로 나타났다. 그리고 고강도 케이싱과 바닥판 계면에서는 케이싱 표면에 요철 또는 거칠기를 주는 것 보다 보수적으로 수평전단철근을 배근하는 것이 소성영역까지 합성 거동을 유지하는 것으로 나타났다.

• Steel and Composite Structures
• /
• 제46권4호
• /
• pp.451-469
• /
• 2023

The use of precast hollow-core slabs (PCHCS) in civil construction has been increasing due to the speed of execution and reduction in the weight of flooring systems. However, in the literature there are no studies that present a finite element model (FEM) to predict the load-slip relationship behavior of pushout tests, considering headed stud shear connector and PCHCS placed at the upper flange of the downstand steel profile. Thus, the present paper aims to develop a FEM, which is based on tests to fill this gap. For this task, geometrical non-linear analyses are carried out in the ABAQUS software. The FEM is calibrated by sensitivity analyses, considering different types of analysis, the friction coefficient at the steel-concrete interface, as well as the constitutive model of the headed stud shear connector. Subsequently, a parametric study is performed to assess the influence of the number of connector lines, type of filling and height of the PCHCS. The results are compared with analytical models that predict the headed stud resistance. In total, 158 finite element models are processed. It was concluded that the dynamic implicit analysis (quasi-static) showed better convergence of the equilibrium trajectory when compared to the static analysis, such as arc-length method. The friction coefficient value of 0.5 was indicated to predict the load-slip relationship behavior of all models investigated. The headed stud shear connector rupture was verified for the constitutive model capable of representing the fracture in the stress-strain relationship. Regarding the number of connector lines, there was an average increase of 108% in the resistance of the structure for models with two lines of connectors compared to the use of only one. The type of filling of the hollow core slab that presented the best results was the partial filling. Finally, the greater the height of the PCHCS, the greater the resistance of the headed stud.