• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.3
• /
• pp.144-148
• /
• 2001

For the purpose of developing capacitive humidity sensor having interdigit electrodes, interdigit electrode was modeled and simulated to obtain capacitance and sensitivity as a function of geometric parameters like the structural gap and thichness. For the development of ASIC, switched capacitor signal conditioning circuits for capacitive humidity sensor were designed and simulated by cadence using 0.25um CMOS process parameters. The signal conditioning circuits are composed of amplifier for voltage gain control, and clock generator for sensor driving and switch control The characteristics of the fabricated sensors are; 1) sensitivity is 9fF/%R.H., 2) temperature coefficient of offset(TCO) is 0.4%R.H./$^{\circ}C$, 3) nonlinearity is 1.2%FS, 4) hysteresis is 1.5%FS in humidity range of 3%R.H. ${\sim}$ 98%R.H.. The response time is 50 seconds in adsorption and 70 seconds in desorption. Fabricated process used in this capacitive humidity sensor having interdigit electrode are just as similar as conventional IC process technology. Therefore this can be easily mass produced with low cost, simple circuit and utilized in many applications for both industrial and environmental measurement and control system, such as monitoring system of environment, automobile, displayer, IC process room, and laboratory etc..

• The Journal of the Korea Contents Association
• /
• v.9 no.12
• /
• pp.566-571
• /
• 2009

In this paper, microstrip bandpass filter combined DCRLH metameterial-cells with a hairpin resonator is designed and fabricated to be transferred only fundamental passband signal, and removed a spurious resonant mode occurring when filter design using a microstrip transmission line is done. The bandpass filter is composed of CCRLH hairpin resonator and DCRLH interdigit metameterial-cells. The hairpin resonator with CCRLH property is implemented between two DCRLH interdigit metameterial-cells with DCRLH property, which is parallel to input port and output port. The interdigit metameterial-cells suppress spurious harmonics occurring on the higher order frequency and improve a filter performance. Insertion loss of the fabricated microstrip bandpass filter on the passband from 1.91GHz to 2.41GHz is 0.2dB, and attenuation on the stopband from 3GHz to 7.7GHz is bellower than -30dB. Therefore, this filter has a good performance for both mobile communications of WCDMA and wireless internet of WiBro.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.79-84
• /
• 2005

This paper proposes the new type of an ion exchange water generator system. The system has an +/- ion exchange membrane located in center and a diagonal-interdigit type electrode applied to a pulsed power. This system is studied in the liquid for the oxidation/reduction potential and the dissolved oxygen concentration by the polarity effects. Consequently, as a diagonal-interdigit type electrode is installed in each side of device, the oxidation/reduction potential and dissolved oxygen concentration by polarity changes and electrical resistivity differences be observed. An ion concentration in the ion exchange water generator system is increased by dissolved oxygen generated from oxidation/reduction potential changes.

• ETRI Journal
• /
• v.9 no.3
• /
• pp.74-85
• /
• 1987

In this paper, a new kind of dual tone multifrequency receiver(DTMFR) is proposed, in which detection is made in terms of the partial correlation(PARCOR) coefficients for efficient DTMF signal detection against both temporary decoding errors by crosstalks possibly coming from adjoint telephone lines during transmission and so-called digit simulation by background voice or noise signals during interdigit period. A simulation study on the behaviour of PARCOR coefficients for tone signals and non-signals has been performed in order to provide the rationale on the feasibility of the proposed DTMFR algorithm. Based upon simulation results, a more refined detection strategy as an example is presented and explained together with the corresponding decision logic.

• Journal of Sensor Science and Technology
• /
• v.21 no.5
• /
• pp.345-351
• /
• 2012

Biomimetic terpene sensors which have high sensitivity and stability have been fabricated using moleculary imprinted polymer (MIP) technology. Since it is impossible to make a resistive type sensor due to the high resistance of MIP, we improved the sensor by adding conductive polymers. We investigated the sensitivity of resistive type sensors with nano particles depending on the amount of conductive polymers. The MIP membrane contained the methacrylic acid as functional monomer and ethylene glycol dimethacrylate as cross linker, which formed specific cavities originated by the target terpene molecules. The mixture of MIP and the conductive polymer was coated on the patterns of interdigit electrodes on the alumina substrate. The fabricated sensors showed their highest specific sensitivities exposed to 500 ppm target gases : limonene 0.055 at 40% of amount of conductive polymers and geraniol $5.84{\times}10^{-4}$ at 20% of amount of conductive polymers. In conclusion, we found that the terpene sensors are affected by the target molecules, functional monomers and the conductive polymers.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.4
• /
• pp.825-834
• /
• 2000

In this paper, we have designed a bandpass filter with via-holes ground on K-band To pass only the 25 ~30% of the bandwidth at the center frequency of 19.6GHz, we have designed a six-order interdigital bandpass filter using microstrip lines. Simulation results of optimization according to via-holes size and numbers of interdigit bandpass filter shows a excellent agreement with theoretical values on passband frequency. Experimental results of BP filters show that mesaured center frequency is 19.150Hz, insertion loss, -4.1dB, reflection coefficient, -16.7dB. It proved that the vis-holes ground size and numbers must be considered to design the bandpass filter.

• Journal of Veterinary Clinics
• /
• v.28 no.1
• /
• pp.163-172
• /
• 2011

Subcutaneous foreign body causes recurrent problems such as chronic soft tissue swelling and discharge. Wooden foreign body is one of the most common foreign bodies found in subcutaneous region including face, interdigit, and thoracic or abdominal area. This report demonstrated three dogs with wooden foreign body located in subcutaneous region of thoracic wall, abdominal wall and upper eyelid, respectively. Three dogs showed prominent soft tissue swelling adjacent the foreign body. A sinus or drainage tract was developed in two of these dogs. Ultrasonography revealed that hyperechoic linear structure accompanied acoustic shadow in all dogs, and which was diagnosed as a subcutaneous foreign body. Anechoic or hyperechoic fluid and hypoechoic tissue circumscribed the foreign body. A subcutaneous foreign body in case 3 was removed by clamp under ultrasound-guide with sedation. Sinography was performed in case 1 and clarified that the wooden foreign body did not perforate the thoracic wall and there was no direct communication into thoracic cavity. Ultrasonography and sinography can be used to identify the subcutaneous foreign body and evaluate the inflammatory reaction and relationship between foreign body and adjacent structures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.942-945
• /
• 2003

Nerve gas sensor based on tin oxide was fabricated and its characteristics were examined. Target gas was dimethylmethylphosphonate($C_3H_9O_3P$, DMMP) that is simulant gas of nerve gas. Sensing material was $SnO_2$ added ${\alpha}-Al_2O_3$ with $4{\sim}20wt.%$ and was physically mixed. And then it was deposited by screen printing method on alumina substrate. Sensor device was consisted of sensing electrode with interdigit(IDT) type in front and heater in back side. Total size of device was $7{\times}10{\times}0.6mm^3$. Crystallite size of fabricated $SnO_2$ were characterized by X-ray diffraction(XRD, Rigaku) and morphology of the $SnO_2$ powders was observed by a scanning electron microscope(SEM, Hitachi). Fabricated sensor was measured as flow type and sensor resistance change was monitored real time using LabVIEW program. The best conditions as added $Al_2O_3$ amounts and operating temperature changes were 4wt.% and $300^{\circ}C$ in DMMP 0.5ppm, respectively. The sensitivity was over 75%. Response and recovery times were about 1 and 3 min., respectively. Repetition measurement was very good with ${\pm}3%$ in full scale.

• Journal of Sensor Science and Technology
• /
• v.13 no.3
• /
• pp.218-223
• /
• 2004

Thin film gas sensor based on tin oxide was fabricated and its characteristics were examined. Target gas is acetonitrile ($CH_{3}CN$) that is simulant gas of blood agent gas. Sensing materials are $SnO_{2}$, $SnO_{2}$/Pt, and (Sn/Pt)oxidation with thickness from $1000{\AA}$ to $3000{\AA}$. Sensor was consisted of sensing electrode with interdigit (IDT) type in front side and a heater in back side. Its dimension was $7{\times}10{\times}0.6mm^{3}$. Fabricated sensor was measured as flow type and monitored real time using PC. The optimal sensing material for $CH_{3}CN$ was {Sn($3000{\AA}$)/Pt($30{\AA}$)}oxidation and its sensitivity and operating temperature were 30%, $300^{\circ}C$ in $CH_{3}CN$ 3 ppm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1217-1223
• /
• 2003

Nerve gas sensor based on tin oxide was fabricated and its characteristics were examined. Target gas is dimethyl methyl phosphonate(C$_3$ $H_{9}$ $O_3$P, DMMP) that is simulant gas of nerve gas. Sensing materials were Sn $O_2$ added a-Al$_2$ $O_3$ with 0∼20wt.% and were physically mixed each material. They were deposited by screen printing method on alumina substrate. The sensor device was consisted of sensing electrode with interdigit(IDT) type in front and a heater in back side. Total size of device was 7${\times}$10${\times}$0.6㎣. Crystallite size & phase identification and morphology of fabricated Sn $O_2$ powders were analyzed by X-ray diffraction and by a scanning electron microscope, respectively. Fabricated sensor was measured as flow type and resistance change of sensing material was monitored as real time using LabVIEW program. The best sensitivity was 75% at adding 4wt.% $\alpha$-Al$_2$ $O_3$, operating temperature 30$0^{\circ}C$ to DMMP 0.5ppm. Response and recovery time were about 1 and 3min., respectively. Repetition measurement was very good with $\pm$3％ in full scale.TEX>$\pm$3％ in full scale.